Hi everyone. I have sampled MC9S12NE64 uc recently and I wonder if NE64 does have it serial monitor program burned in or a BDM is need to burn...

Hi everyone. I have sampled MC9S12NE64 uc recently and I wonder if NE64 does have it serial monitor program burned in or a BDM is need to burn the serial monitor program to NE64. Regards. ------------------------------------

Dear Everyone, I am working with the MC9S12XS128 MCU. This MCU doesnt have the EEPROM but it has D-Flash. And I studied the data sheet...

Dear Everyone, I am working with the MC9S12XS128 MCU. This MCU doesnt have the EEPROM but it has D-Flash. And I studied the data sheet for MC9S12XEP100 refference manual and the application note AN3490.pdf. Which says MC9S12XEP100 has the optional Emulated EERPOM which can be done by carefully partioning the availabe D-Flash. And the document says it has many advantages like .. ...

Good day everyone, =20 I am working on MC9S12XS128 MCU. =20 I know that this MCU has the new feature of D-Flash. I am facing a problem in...

Good day everyone, =20 I am working on MC9S12XS128 MCU. =20 I know that this MCU has the new feature of D-Flash. I am facing a problem in using this and executing its commands on it. I am not very clear about this D-Flash and have the following questions =20 I do not want to use the Global address in my project, so after reviewing the datasheets, i am thinking that a 1Kbyte D-flash is av...

I am developing code for a hand-held product that uses the MC9S12D64 processor. The product uses the internal EEPROM to store a number of...

I am developing code for a hand-held product that uses the MC9S12D64 processor. The product uses the internal EEPROM to store a number of 4-byte calibration values, generated when the product is calibrated. I am using the PEMicro's Win32, PROG12Z and ICD12Z programs to author, program and debug the code, connecting to the BDM via PEMicro's Multilink USB Multilink interface. The code i...

Hi, I would like to migrate a project written for 9S12A to a 9S12XA using Freescale Codewarrior 4.6. Is there any possibility to make it...

Hi, I would like to migrate a project written for 9S12A to a 9S12XA using Freescale Codewarrior 4.6. Is there any possibility to make it easily ? (excepting some parameters due to clock....) Thanks. -- ------------------------------------

Is there a way to compile and link a CodeWarrior project from a command line, like a batch file or something? If so could somebody explain how...

Is there a way to compile and link a CodeWarrior project from a command line, like a batch file or something? If so could somebody explain how or point me in the right direction for the documentation on this? Thanks, Eric ------------------------------------

hi i am in need for the fuzzytech mp programme that help me in my project to c= ontrol the dc motor from the fuzzy to put it to the pic...

hi i am in need for the fuzzytech mp programme that help me in my project to c= ontrol the dc motor from the fuzzy to put it to the pic programme ( 18f452)= if any one can help me and send it to me or any place to get it from thier= i will be thankful . =C2=A0 many thank peter=C2=A0 __________________________________________________________ Sent from Yahoo! Mail. A Smarter Email ...

Hello, I am trying to work with the MSCAN-Module of the HCS12. I have CAN-Dongle for a PC and try to send a CAN Message from the PC to the...

Hello, I am trying to work with the MSCAN-Module of the HCS12. I have CAN-Dongle for a PC and try to send a CAN Message from the PC to the HCS12. I receive the message with the HCS12 and show the data at some LED's. But at the Computer I always get the Error-Message BUSHEAVY. Could you have a look at my code for the HCS12 and tell me what's wrong. Perhaps the baud rate is wrong. ...

I want to set the baud rate for the SCI based on user selection. So I am setting SCI1BDH and SCI1BDL depending on what the baud rate is selected...

I want to set the baud rate for the SCI based on user selection. So I am setting SCI1BDH and SCI1BDL depending on what the baud rate is selected (choices are limited to a few standard baud rates). However, it seems like any baudrate that requires setting of SCI1BDH does not work. Bus Speed is 24MHz I allow the following baud rate: 38.4K, BR = 39 (default) 19.2K, BR = 78 9600, BR = ...

We are hving trouble getting out MC9S12E128MFUE to run without the BDM interface. Things are OK when reset and run from the P&E interface but...

We are hving trouble getting out MC9S12E128MFUE to run without the BDM interface. Things are OK when reset and run from the P&E interface but the chip does not run as standalone. What wrong? ------------------------------------