Hi everyone, Can u suggest me some projects using HCS12 -- Regards Srinivas.

Hi everyone, Can u suggest me some projects using HCS12 -- Regards Srinivas.

Hi there, I am working on a Freescale HC12 chip connected to an Axiom CSM12D Board, but cannot successfully enter debug mode. If I hook up...

Hi there, I am working on a Freescale HC12 chip connected to an Axiom CSM12D Board, but cannot successfully enter debug mode. If I hook up the board, communication can be established with the AxIDE terminal. The following message is displayed: Axiom Manufacturing CSM12D Education Module MC9S12DT256 MCU This message is displayed everytime the RESET button is pressed that s...

Hi everyone, I am working on MC9S12XDP512 mcu using HCS12X starter kit, I am not very good at MCU knowledge right now. During my work, I...

Hi everyone, I am working on MC9S12XDP512 mcu using HCS12X starter kit, I am not very good at MCU knowledge right now. During my work, I got stuck in the Memory map concept in this MCU. I created a project using Codewarrior(Version 5.7.0). I just initialized the PLL module and use some basic code to glow the LED's and downloaded the soruce to the Starter kit using BDM and its working...

hi everyone, can any one tell me the initial default value for the varibles which are placed in the NO_INIT location by modifying the...

hi everyone, can any one tell me the initial default value for the varibles which are placed in the NO_INIT location by modifying the .prm file. I am using Codewarrior for this. I modifed my project .prm file, like below using NO_INIT, so that the variables which are declared in the RAM area from 0x2000 to 2005 will not be initialized to zero by default. when...

Hi all I am using the PEmicro USB HCS08 / HCS12 Multilink unit for programming / debugging. The unit is working good with simple projects,...

Hi all I am using the PEmicro USB HCS08 / HCS12 Multilink unit for programming / debugging. The unit is working good with simple projects, but when I am trying to run the CW debugger using this unit connected to the target board, and the project includes several active interrupts like: SCI + 2x PWM , the device lose synchronization and I can't debug Did anyone knows how to handle it...

Hi, May I know how long a delay needed between each transmission by using RS232? Beside that, how can I determine the delay...

Hi, May I know how long a delay needed between each transmission by using RS232? Beside that, how can I determine the delay period? Thanks,. yeehaw

Hi I purchased Kevin Ross BDM12 pod years ago and didn't use it for a while. Right now i try to use it but i can't find the DB12.exe file...

Hi I purchased Kevin Ross BDM12 pod years ago and didn't use it for a while. Right now i try to use it but i can't find the DB12.exe file (actually the serial communication / debugger program for the pod in DOS environment if i remember well). I visit kevin's web site but there is not a link for the program. I even email Kevin Ross but so far nothing. So please if anyone has that program,...

Hello ! Until now, I was using mc9s12dp256 with ICC12 V6 professionnal, paged programm, and all was ok. Now, using mc9s12xdp512cal, with...

Hello ! Until now, I was using mc9s12dp256 with ICC12 V6 professionnal, paged programm, and all was ok. Now, using mc9s12xdp512cal, with ICC12 professionnal V6, I need to use XGate processor (communication SCI between 2 MCU). Without XGate, the main S12 CPU would be overload ! I read the Freescale datasheets, specially the chapters about : - XGate, - Memory Mapping Control - Interru...

hcs12mem 1.4.1 is available. http://cml.mfk.net.pl/hcs12mem/ Previously known as hc12mem, now renamed to hcs12mem, due to some confusion...

hcs12mem 1.4.1 is available. http://cml.mfk.net.pl/hcs12mem/ Previously known as hc12mem, now renamed to hcs12mem, due to some confusion which MCU family it supports: hc12mem name suggested that's HC12 family, but in reality it currently works only with S12 chips. hcs12mem is a tool for S12 MCUs, allowing for reading/writing internal memories (FLASH/EEPROM), protecting/unprotecting ...

Dear All Can you help to generate pwm signals using MC9S12DP512 Thankyou ...

Dear All Can you help to generate pwm signals using MC9S12DP512 Thankyou _____________________________________________________________________________ Ne gardez plus qu'une seule adresse mail ! Copiez vos mails vers Yahoo! Mail