68HC1 | 812A4 | 9S12DP256 | Bootloader | CodeWarrior | D60A | Debugger | DP256 | ECT | EEPROM | EVB | Flash | HC1 | HCS12 | I2C | IAR | ICC1 | Interrupts | LCD | M68KIT912DP256 | MC9S12DP256 | MC9S12DP256B | Metrowerks | Motor | MSCAN | Multilink | PLL | Quadrature | SDI | SPI | Transceiver | XFC

I just start to use the M68EVB9S12C32 evaluation board from Axiom,
yet got stuck at the very beginning. Following the manual of this
evaluation board, I built a empty test project via the wizard of
CodeWarrior for HC12 (4.5). After connecting the SCI port with COM1
using the provided cable, and power on the target board, I tried to
enter debug, but after the progress bar displays "erased
flash",..., "executing xxx.cmd ", a connection error appears
showing "the target does not respond to communication request", and
the progress bar is located behind this message area; please refer to
the attached screenshot of this error message.

If the EVB board is powered off, and do the debug again, the same
error message appears but the progress bar doesn't.

I then tried the companion HCS Serial Monitor Interface(a Visual
Basic soft), the target board can be initialized successfully, and
response is also received from the target!

Anybody can kindly give suggestion?

What follows are some details of the settings.
The project is set to serial monitor mode, and main.c file contains
only the following two lines:
EnableInterrupts;
for( ; ; ) {}

I tried the jumpers settings suggested at these threads:
http://tech.groups.yahoo.com/group/68HC12/message/9014
http://tech.groups.yahoo.com/group/68HC12/message/12190
but no effect.

Different baud rates are tried, like 115200, 9600, 192000, etc.,once
again without effect.

I also tested under the original CodeWarrior 3.0 and installed the
service pack, the debugger hangs for a long time then gives HI-WAVE
error "target not ready or not connected on COM1".



(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

please may I have this email
Andrew Lohmann AMIIE
Design Engineer

PLEASE NOTE NEW EMAIL ADDRESS IS:
a...@bellinghamandstanley.co.uk

Bellingham + Stanley Ltd.
Longfield Road, Tunbridge Wells, Kent, TN2 3EY, England.
Tel: +44 (0) 1892 500400
Fax: +44 (0) 1892 543115
Website: www.bs-ltd.com

radeonwu wrote:

>*** This e-mail has been modified by Finjan's Vital Security for E-Mail.
>*** More details can be found in the attached file, Vital Security Notification.html
>
>
> ------------------------------------------------------------------------
>
> This e-mail message was modified by Vital Security for E-Mail on
> 1Box.bellinghamandstanley.co.uk due to security violations.
> ******************************************************************************************
> 1. E-mail body part Body_1.txt was blocked.
> Reason: Forbidden content category 'Adult Content Spam'
>
> 2. E-mail body part Body_2.htm was blocked.
> Reason: Forbidden content category 'Adult Content Spam'
> Original unmodified data was quarantined under ID 116675141827663636.eml
>
> This information has been blocked due to possible security
> implications. This URL has been blocked using the current usage rules
> in the Bellingham + Stanley Ltd Acceptable Usage Policy. If this URl
> is blocked in error please contact System Administrator for further
> information.
> ******************************************************************************************
> Vital Security for E-Mail - Proactive Security from Finjan Software
-----------------------------Disclaimer-----------------------------

This communication contains information which is confidential and may also be privileged. It is for the exclusive use of the addressee. If you are not the addressee please note that any distribution, reproduction, copying, publication or use of this communication or the information is prohibited. If you have received this communication in error, please contact us immediately and also delete the communication from your computer. We accept no liability for any loss or damage suffered by any person arising from use of this e-mail.

-----------------------------Disclaimer-----------------------------


(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

--- In 6...@yahoogroups.com, Andrew Lohmann wrote:
>
> please may I have this email

What do you mean... do you want to see the message which you replied to:
http://tech.groups.yahoo.com/group/68HC12/message/14823

>
> radeonwu wrote:
>
> >*** This e-mail has been modified by Finjan's Vital Security for
E-Mail.
> >*** More details can be found in the attached file, Vital Security
Notification.html
> >
> >
------------------------------------------------------------------------
> >
> > This e-mail message was modified by Vital Security for E-Mail on
> > 1Box.bellinghamandstanley.co.uk due to security violations.
> >
******************************************************************************************
> > 1. E-mail body part Body_1.txt was blocked.
> > Reason: Forbidden content category 'Adult Content Spam'
> >
> > 2. E-mail body part Body_2.htm was blocked.
> > Reason: Forbidden content category 'Adult Content Spam'
> >
> >
> > Original unmodified data was quarantined under ID
116675141827663636.eml
> >
> > This information has been blocked due to possible security
> > implications. This URL has been blocked using the current usage rules
> > in the Bellingham + Stanley Ltd Acceptable Usage Policy.
> > If this URl
> > is blocked in error please contact System Administrator for
> > further information.
> >
******************************************************************************************
> > Vital Security for E-Mail - Proactive Security from Finjan
> > Software
... BLAH, Ha, Ha, Ha, Ha!!
You must be really messed up if your email administrator quarantines
your technical email addresses for "adult content". But the worst part
is you can't just get it back from him... you have to go and ask the
group for it again... What makes you think he would let it through
this time?

______________________________
Stellaris® MCU Family: New Parts, New Package, New Price.


(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

Sorry about the message post seasonal break glitch. I should have sent
the email to our technical support as it got caught it our spam filter.
The averting attached to forum messages is inconvenient.

> please may I have this email

What do you mean... do you want to see the message which you replied to:
http://tech.groups.yahoo.com/group/68HC12/message/14823


Andrew Lohmann AMIIE
Design Engineer

PLEASE NOTE NEW EMAIL ADDRESS IS:
a...@bellinghamandstanley.co.uk

Bellingham + Stanley Ltd.
Longfield Road, Tunbridge Wells, Kent, TN2 3EY, England.
Tel: +44 (0) 1892 500400
Fax: +44 (0) 1892 543115
Website: www.bs-ltd.com

-----------------------------Disclaimer-----------------------------

This communication contains information which is confidential and may also be privileged. It is for the exclusive use of the addressee. If you are not the addressee please note that any distribution, reproduction, copying, publication or use of this communication or the information is prohibited. If you have received this communication in error, please contact us immediately and also delete the communication from your computer. We accept no liability for any loss or damage suffered by any person arising from use of this e-mail.

-----------------------------Disclaimer-----------------------------


(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

--- In 6...@yahoogroups.com, Andrew Lohmann wrote:
>
> Sorry about the message post seasonal break glitch. I should have
> sent the email to our technical support

I thought it was a holiday related hickup... too much eggnog ;)

> http://tech.groups.yahoo.com/group/68HC12/message/14823
Actually, I use the website all the time... no need to switch because
email had no advantage. You should try it, just a matter of using
search instead of the work of filtering messages other ways to keep track.



(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

--- In 6...@yahoogroups.com, "Jefferson Smith" wrote:

> > Sorry about the message post seasonal break glitch. I should have
> > sent the email to our technical support
>
> I thought it was a holiday related hickup... too much eggnog ;)

I note it was rejected due to the graphical contents, probably a glitch in the artwork:-)

Cheers,

Theo



(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )

Problem solved.
I got a P&E USB multilink pod, and reflashed the Freescale AN2548
serial monitor, then everything turns ok.

______________________________
Stellaris® MCU Family: New Parts, New Package, New Price.


(You need to be a member of 68hc12 -- send a blank email to 68hc12-subscribe@yahoogroups.com )