Sign in
Search AT91SAM
Subscribe to AT91SAM
Ads
Discussion Groups
See Also
AT91SAM ARM
For users of the Atmel AT91SAM7 and AT91SAM9 ARM CPU chips. Atmel has taken a new direction by combining on chip flash and ram with the ARM CPU on a single die. This provides low cost devices for small systems using the ARM CPU. This group is to exchange information to help users get started and learn how to use the devices.
SAM3U with USB2.0 HS announced [7 Articles]
lpc2100_fan - Jun 3 2009
Hi,
The Cortex-M3 market gets more and more competitive and announcements come out more and more premature. When reading these really very interesting press releases do not pla... 
Who have the PCB of at91sam7se-ek board ? [2 Articles]
"jec...@ymail.com" - Jun 1 2009
Who have the PCB of at91sam7se-ek board ?
Can you send me a copy?
------------------------------------
... =?iso-8859-1?B?aGVscD9hYm91dCBkbTkwMDBhP8fz1vo=?=
"jec...@ymail.com" - May 31 2009
SGmjrGV2ZXJ5Ym9keQpJIHdvdWxkIGxpa2UgdG8gYXNrIHdoZW4gRE05MDAwQSBjb25maWd1
cmVkIGNvcnJlY3RseSwgd2hhdCBwZXJmb3JtYW5jZT8gCkkgd291bGQgbm93IGxpa2UgdG8g
dGVzdCB0aGUgYXQ5MXNhbTdzZTMyIEJv... problem with iar (at91sam7s128)
Shakeel - May 28 2009
Hi
i have written following code in iar embedded workbench for at91sam7s128,as i wanted to simluate it without a harware board.
#include
void main (void)
{
AT91C_BASE_P... help?at91sam7se32-ek board?test ethernet? [3 Articles]
"jec...@ymail.com" - May 27 2009
Hi,everybody
my final result is communication over Ethernet using
TCP/IP. The TCP/IP stack I don't like to write by my own, therefore
I like to use usos with the tcp/ip. Has a... help?how to posts uc-os to at91sam7se32-ek board? [5 Articles]
"jec...@ymail.com" - May 27 2009
Hi , all
i have found the example of porting uc os to at91sam7se512-ek board in this web site :
http://www.micrium.com/atmel/AT91SAM7.html
but my board is at91sam7se32 and with ... problem with GPIO port c pins on AT91SAM9260 CU-ES
Virupax SS - May 26 2009
Hi
I am using AT91SAM9260 CU-ES atmel processor which is a revised version of
the ( AT91SAM9260 CJ ) processor. I have the code in u-boot and kernel to
toggle the port C pi... No Subject
Virupax SS - May 26 2009
Hi
I am using AT91SAM9260 CU-ES atmel processor which is a revised version of
the ( AT91SAM9260 CJ ) processor. I have the code in u-boot and kernel to
toggle the port C pin... AT91SAM7X256 Capture interface
firefoxrabbit - May 25 2009
I have connected on "Timer/Counter Channel 0" port A a rpm sensor (square signal every spark) and a speed sensor (square signal every axle rotation). Now my question is: is possibl... at91sam7s PIO set to output 0 but connected to power plane [7 Articles]
yeayeah85 - May 21 2009
Hi!
How can I check if I might burn the uC if I switch the pin to output 0 but the pin stays high because connected to power plane?
...
Set PIO to output
Try to pull line l...