Sign in
Search avrclub
Subscribe to avrclub
avrclub by Keywords
AT90S2313 | AT90S8515 | ATMega | ATmega128 | ECL | FETS | IAR | Keyboard | LCD | STK50 | TMOS | UART
Ads
Discussion Groups
Discussion Groups | AVRclub | Reset (?) trouble with the AT90S2313
Atmel AVR Microcontroller discussion group.
Reset (?) trouble with the AT90S2313 - sjoerdoptland - May 8 17:45:00 2003
Hello all,
Although I'm very new here and haven't got time to listen what's
going on here I will pose my question, and I hope you'll forgive me
and take a little while to answer. Thanks a lot.
I built the MiniDMX interface of Mathias Dzionsko (1, see below)and
tried to program it with blinktest.flash (2). BTW, I programmed the
2313 with the fa1fb programmer (3), so not in-system. The programming
seemed to work (verification OK). Then I put the 2313 in the system
and powered-on.
The behavior of the circuit was very strange. It should blink the 3
LEDs subsequently, but there sometimes was one on, sometimes not,
anyway, after the starting situation it wouldn't go on; the processor
got 'stuck'. One other remark: when I pulled out and plugged in the
wall-wart adapter subsequently quick, the processor would sometimes
go to the next 'step' in blinking the LEDs...
Strange, or am I missing something obvious?
(1) Schematic MiniDMX:
http://www.dzionsko.de/minidmx/schaltpl.gif
(2) Source blinktest
http://81.68.211.163/blinktest.txt
(3) Info fa1fb
http://www.qsl.net/ba1fb/
(see under 'ATMEL AVR MCU ISP programmer')
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
Although I'm very new here and haven't got time to listen what's
going on here I will pose my question, and I hope you'll forgive me
and take a little while to answer. Thanks a lot.
I built the MiniDMX interface of Mathias Dzionsko (1, see below)and
tried to program it with blinktest.flash (2). BTW, I programmed the
2313 with the fa1fb programmer (3), so not in-system. The programming
seemed to work (verification OK). Then I put the 2313 in the system
and powered-on.
The behavior of the circuit was very strange. It should blink the 3
LEDs subsequently, but there sometimes was one on, sometimes not,
anyway, after the starting situation it wouldn't go on; the processor
got 'stuck'. One other remark: when I pulled out and plugged in the
wall-wart adapter subsequently quick, the processor would sometimes
go to the next 'step' in blinking the LEDs...
Strange, or am I missing something obvious?
(1) Schematic MiniDMX:
http://www.dzionsko.de/minidmx/schaltpl.gif
(2) Source blinktest
http://81.68.211.163/blinktest.txt
(3) Info fa1fb
http://www.qsl.net/ba1fb/
(see under 'ATMEL AVR MCU ISP programmer')
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
Re: Reset (?) trouble with the AT90S2313 - sjoerdoptland - May 9 19:05:00 2003
Hello all,
The problem is solved now, so I hope not being to much of a
disturbance to you.
Regards,
Sjoerd
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
The problem is solved now, so I hope not being to much of a
disturbance to you.
Regards,
Sjoerd
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
AW: [AVR club] Re: Reset (?) trouble with the AT90S2313 - Klaus Ruebsam - May 10 4:40:00 2003
Hi Sjoerd,
Would you like to tell us about the reason for the problems (I do not
want to die as a stupid man).
Kind regards,
Klaus
-----Ursprüngliche Nachricht-----
Von: sjoerdoptland [mailto:sjoerdoptland@sjoe...]
Gesendet: Samstag, 10. Mai 2003 01:05
An: avrclub@avrc...
Betreff: [AVR club] Re: Reset (?) trouble with the AT90S2313 Hello all,
The problem is solved now, so I hope not being to much of a
disturbance to you.
Regards,
Sjoerd
To unsubscribe from this group, send an email to:
avrclub-unsubscribe@avrc...
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
Would you like to tell us about the reason for the problems (I do not
want to die as a stupid man).
Kind regards,
Klaus
-----Ursprüngliche Nachricht-----
Von: sjoerdoptland [mailto:sjoerdoptland@sjoe...]
Gesendet: Samstag, 10. Mai 2003 01:05
An: avrclub@avrc...
Betreff: [AVR club] Re: Reset (?) trouble with the AT90S2313 Hello all,
The problem is solved now, so I hope not being to much of a
disturbance to you.
Regards,
Sjoerd
To unsubscribe from this group, send an email to:
avrclub-unsubscribe@avrc...
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
Re: AW: [AVR club] Re: Reset (?) trouble with the AT90S2313 - Sjoerd Op 't Land - May 10 5:35:00 2003
Klaus Ruebsam wrote/ schreef:
> Hi Sjoerd,
>
> Would you like to tell us about the reason for the problems (I do not
> want to die as a stupid man).
A very good motive ;-). Actually it was something quite trivial: the
processor stopped eating instructions because the Xtal wasn't soldered
properly. I already checked it once, but only the second time the problem
showed up...
> Kind regards,
>
> Klaus
Regards, / Groeten,
Sjoerd
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )
> Hi Sjoerd,
>
> Would you like to tell us about the reason for the problems (I do not
> want to die as a stupid man).
A very good motive ;-). Actually it was something quite trivial: the
processor stopped eating instructions because the Xtal wasn't soldered
properly. I already checked it once, but only the second time the problem
showed up...
> Kind regards,
>
> Klaus
Regards, / Groeten,
Sjoerd
(You need to be a member of avrclub -- send a blank email to avrclub-subscribe@yahoogroups.com )