I have a bx24 and a bs2p24. The program that i have on the bs2p is communicating serial out at 9600 8-no parity-inverted and does...

I have a bx24 and a bs2p24. The program that i have on the bs2p is communicating serial out at 9600 8-no parity-inverted and does work. However when I move the program over to bx24, it dont work. I've monitored the bx24 as it sends data out through hyperterminal, but with the

Hey everyone ! I was just wondering, I'm using two KP4M2-008 stepper motors for a small robot my son and I are building, I...

Hey everyone ! I was just wondering, I'm using two KP4M2-008 stepper motors for a small robot my son and I are building, I finally got everything to work, including the IRsensor, and put it on the ground. I don't seem to be getting the kind of power( torque) I was hoping for ( Not even close ).

Hi. I'm using the BX24 to control a DC motor. I have the PWM output of the BX24 hooked up to an N-channel MOSFET. (I'm not using an...

Hi. I'm using the BX24 to control a DC motor. I have the PWM output of the BX24 hooked up to an N-channel MOSFET. (I'm not using an H- bridge because I don't need reverse.) Even though the MOSFET is rated 25 amps and should easily handle the motor current it keeps burning out. Aft

I am using winXP and com port 3. I get Error code 217 and Unable to halt messages when I try to download a simple LED ...

I am using winXP and com port 3. I get Error code 217 and Unable to halt messages when I try to download a simple LED program...but for some reason every now and then I get EEPROM download error - *** Opening file: C:\Program Files\BasicX\Project1.bxb *** Downl

Colleagues, The SRF08 was pointed verticaly to the ceeling, which was 150" away. There was also an incondescent ligth 70" away...

Colleagues, The SRF08 was pointed verticaly to the ceeling, which was 150" away. There was also an incondescent ligth 70" away from SRF08. I expected to get the first bounce reading of 70", but it actually was 28". Although at short distances (under 10&q

I have just bought a KC7783 PIR sensor and I am trying to connect it to my BX-24. I actually thought it would just give a logic...

I have just bought a KC7783 PIR sensor and I am trying to connect it to my BX-24. I actually thought it would just give a logic high when movement is detected. But it has a TTL output - how do I syncronize this with the BX? The datasheet can be found on

Hi all, I need to send and receive (sending is the most critical, receive can be done at other rates/parity modes) serial data...

Hi all, I need to send and receive (sending is the most critical, receive can be done at other rates/parity modes) serial data in 8-bit, odd parity, 9600bps from a BX24, has anyone got any bit-bashed routines for doing this? I've been searching around, but found nothing useful

Hello, I am building a sunroof control system for a friends car. It will automatically close the sunroof from the tilt or...

Hello, I am building a sunroof control system for a friends car. It will automatically close the sunroof from the tilt or slide position when the car is turned off. The project has grown, since now I am now utilizing a 4 line Serial LCD+ to display the time, date, and contr

Hi members Try to connect LCD KS0713 controller in serial mode to my BASICX-24. (I use SID, RS, SCLK without any Pull Up...

Hi members Try to connect LCD KS0713 controller in serial mode to my BASICX-24. (I use SID, RS, SCLK without any Pull Up resistors) ANYONE know of any BASICX-24 codes somewhere that works? Modified "LCD_595 by Jon Williams over and over" but the LCD

Hello I am having a problem with the code below. The Delphi & BX-24 codes appears to work ok except for the following. I seem...

Hello I am having a problem with the code below. The Delphi & BX-24 codes appears to work ok except for the following. I seem to be getting 0's sent to the BX-24 (or the BX-24 is picking up false data somewhere) which causes false data readings. I inserted "If Dat >