2106 | ADC | ARM7 | Atmel | Bootloader | CAN | CrossStudio | CrossWorks | DDS | ECos | Ethernet | ETM | FIFO | FLASH | FPGA | GCC | GDB | GNU | GNUARM | GPIO | I2C | IAP | IAR | JTAG | Kickstart | LCD | Linux | LPC | LPC-E2294 | LPC2000 | LPC2100 | LPC2104 | Lpc2106 | Lpc210x | LPC2114 | LPC2119 | LPC2124 | LPC2129 | Lpc2138 | LPC213x | LPC21xx | LPC2210 | LPC2212 | LPC2214 | LPC2292 | LPC2294 | LPC2xxx | LPC3128 | MCB2100 | Olimex | Philips | PWM | Rowley | RTC | RTOS | SPI | SSP | UART | UART0 | UART1 | ULINK | USB | Watchdog | Wiggler

I was given a atmel SAM-ICE which is used on the atmel arm 7
controller. I wonder will it work with the nxp evaluation boards ? I
am thinking about getting a keil eval board.

Will it work ?

Thanks!



(You need to be a member of lpc2000 -- send a blank email to lpc2000-subscribe@yahoogroups.com )

Hi:

The SAM-ICE won't work with NXP processors. It is a limited JTAG
debugger only for Atmel MCU.

I would suggest get a JLINK(IAR) or ULINK2(Keil).

Regards,

Alex

--- In l...@yahoogroups.com, "email_kc" wrote:
>
> I was given a atmel SAM-ICE which is used on the atmel arm 7
> controller. I wonder will it work with the nxp evaluation boards ? I
> am thinking about getting a keil eval board.
>
> Will it work ?
>
> Thanks!
>



(You need to be a member of lpc2000 -- send a blank email to lpc2000-subscribe@yahoogroups.com )

ariberospot wrote:
>
> Hi:
>
> The SAM-ICE won't work with NXP processors. It is a limited JTAG
> debugger only for Atmel MCU.
>
> I would suggest get a JLINK(IAR) or ULINK2(Keil) .
>

Or, you can go the route of the OpenOCD + a USB JTAG unit for < $80.
See: http://www.openhardware.net/Embedded_ARM/OpenOCD_JTAG/

It worked well for me on a Mandriva Linux box. I'm sure that you could
put something similar together for a windows box as well, and as
cheaply. I would suggest you forgo a wiggler if you can afford it.

TomW

--
Tom Walsh - WN3L - Embedded Systems Consultant
http://openhardware.net http://cyberiansoftware.com http://openzipit.org
"Windows? No thanks, I have work to do..."
----------------------------------------------------



(You need to be a member of lpc2000 -- send a blank email to lpc2000-subscribe@yahoogroups.com )

Hi,

I got a few problem and really hope someone can help me.
I new with ARM architecture and trying to get use to it.
I am using ADS 1.2 evaluation for ARM7TDMI.

my problem were:
1. after compiling and its start to linking my computer hang/jammed.
I believe that my computer meet the minimum requirement for ADS 1.2.
or it is because of my firmware error,like wrong memory mapping?

2. right now I need to convert firmware which is originally using ARM60 to ARM7TDMI(GP4020). I change the MPC, interrupt, register address, but it seem not working.
can someone who knows something help me.

thanks a lot,
a_salam_saad
_._,___
Terima Kasih,
a_salam_saad

---------------------------------
Get the free Yahoo! toolbar and rest assured with the added security of spyware protection.

[Non-text portions of this message have been removed]


(You need to be a member of lpc2000 -- send a blank email to lpc2000-subscribe@yahoogroups.com )