27c256 | 4K81H | 68HC11A1 | 68HC11P1 | 68hc24 | 68HC711E9 | 68HC811 | 8255 | A2D | ADC | ADC12138 | Am85C30 | BRCLR | Buffalo | CMOS | EEPROM | EPROM | Ethernet | EVB | EVBU | HC11E1 | HC11E9 | HC711E9 | Horray | ImageCraft | IRQ | Keypad | LCD | MC68HC11D0FN | MC68HC11E1CFU3 | MC68HC11F1 | MC68HC711E9 | MC68HC711E9CFN2 | Microcore11 | Microstamp11 | Minikit | NVRAM | PSD | PSD8xx | PSD9xx | PT1000 | RS232 | RTS | RXD | SPI | SRAM | TXD | Watchdogs | XIRQ

Re: 68HC811 [was 68HC24 PRU]

I've been considering moving my higher-needs designs to them, too. They seem to be a much better choice than the HC12. ----- Original Message ----- From:...

help with the 68hc24 pru   [7 Articles]

hello everyone im trying to connect the 68hc24 pru to a hc11e1. i have made the follwoing connections and still cant get the pru to interface with the hc11. ...

RE: 68HC811 [was 68HC24 PRU]

So far i have figured out how to open and close the program ;) John Samperi cc: Subject: RE: [m68HC11] 68HC81...

RE: 68HC811 [was 68HC24 PRU]

My last project was on a at90s8535. It went easy, but for my current project, I need some MUSCLE John Samperi ...

RE: 68HC811 [was 68HC24 PRU]

It's from digikey #mc56f8300dsk-nd The board comes with the 56f8323 (12 bit adc) It has a touch sensor on the board for proximity testing, comes with metrowerks 8...

RE: 68HC811 [was 68HC24 PRU]

Jamie, Where did you get your $79 evaluation board? Thanks, Emmett Redd Ph.D. mailto: Associate Professor (417)836-5221 Department of Physics, Astron...

RE: 68HC811 [was 68HC24 PRU]

John, you could jump back to motorola with the mc56f8323 flash dsp. I just got an evaluation board for $79 !! (in the US). Seems to work as promissed. It has both m...

RE: 68HC811 [was 68HC24 PRU]

At 07:53 AM 20/11/03 -0600, you wrote: > comes with >metrowerks 8k PERMANENT lisence. That's a monster of a program!!! I got one with a hc08 evaluation boar...

Re: 68HC811 [was 68HC24 PRU]

In a message dated 11/19/03 3:26:14 AM Eastern Standard Time, writes: Motorola would get some of my business back if they did...but they have to hurry up bef...

RE: 68HC811 [was 68HC24 PRU]

At 07:47 AM 19/11/03 -0600, you wrote: >John, you could jump back to motorola with the mc56f8323 flash dsp. I just >got an evaluation board for $79 !! (in the US). ...

I/O expansion   [2 Articles]

--- In , "Bob Smith" wrote: > Sorry about the typo -- > > > See the 74HC165 for input ports and the 74HC794. > > should read - > > > S...

RE: 68HC811 [was 68HC24 PRU]

Regarding the 68HC811-- There used to be a significant hole in Motorola's line-up, as between the 68HC11 product line, and the 68HC12, and a lot of people didn'...

RE: 68HC811 [was 68HC24 PRU]

Kerry Berland <> wrote: [MC9S12E64CFU cheaper and better] > more memory. It runs at 25 MHz bus speed, 12.5 times as fast as the > example 68HC11 above. This...

Re: 68HC811 [was 68HC24 PRU]

At 10:39 AM 19/11/03 EST, you wrote: >You know, John, since the spinoff of Moto semi as a separate business, they >might be more receptive to feedback from the fie...

RE: 68HC811 [was 68HC24 PRU]

At 08:09 PM 18/11/03 -0600, you wrote: >Regarding the 68HC811-- > >There used to be a significant hole in Motorola's line-up, as between >the 68HC11 product li...

Re: tekmos PRU   [2 Articles]

--- In m68HC11@m68H..., "teejsd" wrote: > > Hello. I am a nontrad college punk out here in the sticks of South > Dakota. > Can anybody help me with setting...

RE:

Hi, We use the MiniIDE, http://www.mgtek.com/products/miniide/, for development, assembly and moving the code to RAM. Works quite well. Free down load for a "...

Re: 68HC11 E2   [4 Articles]

Hi Kerry, I don't think the 68HC11 will be red for some time. There are too many thing made that use them still in production. I agree that using them for new desig...

Re: 68HC811 [was 68HC24 PRU]

----- Original Message ----- From: "Kerry Berland" <> To: <> > Regarding the 68HC811-- > > There used to be a significant hole in Motorola's line-up, as...