EmbeddedRelated.com
The 2024 Embedded Online Conference

Image processing with MSP430

Started by anbu...@yahoo.com in MSP43010 years ago 9 replies

Hi, I'm new to the group, My question is does image processing is possible with MSP430G2? Actually I'm new to MSP430. I'm good at arduino....

Hi, I'm new to the group, My question is does image processing is possible with MSP430G2? Actually I'm new to MSP430. I'm good at arduino. Does an MSP contain RF transceiver within itself? Please help me


Security fuse blown on MSP430FR5736

Started by Peter Grey in MSP43010 years ago 8 replies
IAR

Hi I was programming and debugging code on a MSP430FR5736 over the past few days and then this morning started again and found that I got...

Hi I was programming and debugging code on a MSP430FR5736 over the past few days and then this morning started again and found that I got the message that security fuse flown or device not recognised. In the log it said security fuse blown. I have looked back through previous post but could find nothing that helped. I am using MSP-430UIF and IAR ass


PWM on MSP430 Micro

Started by john Mcdonald in MSP43010 years ago 2 replies

Hello all, I was just checking to see if I am correct please. ?If I set up the TIMER 1 on MSP430F5438A as a PWM therefore all the TA1pins like...

Hello all, I was just checking to see if I am correct please. ?If I set up the TIMER 1 on MSP430F5438A as a PWM therefore all the TA1pins like TA1.0, TA1.1 and TA1.2 have the same period but can have different duty cycle ? ?Am I correct? Thanks, John.


Problems with RTC_B and MSP430FR5736

Started by Peter Grey in MSP43010 years ago 3 replies

I am having problems putting the device into LPM3.5 and then waking up with a RTC event. Initially I put the program in a loop after setting...

I am having problems putting the device into LPM3.5 and then waking up with a RTC event. Initially I put the program in a loop after setting the time/date and alarm registers. I am looking for a change in minutes. I can detect this event. When I put it into LPM3.5 as per the user guide it just sits there. I am using a UIF-FET and if I try and stop it the program crashes saying the security fu...


Ok, lets get something going

Started by w8tf...@yahoo.com in MSP43010 years ago 6 replies

Hello Everyone: I have been around for a while,but have not done much with my launchpad. So lets get started, I am a newbee to most of you...

Hello Everyone: I have been around for a while,but have not done much with my launchpad. So lets get started, I am a newbee to most of you and that is where I will start. I want to do somethings with my Launchpad, so I will ask the group what is the best first project to start with and then we (or I) can go from there. I am a Ham Radio Operator and have some IDEAS, and yes I do know about...


USB Interface

Started by john Mcdonald in MSP43010 years ago 2 replies

Dear all, I needed to do a firmware update on MSP430F5xx. ?I was wondering what is the minimal code I need to install on my micro to recognize...

Dear all, I needed to do a firmware update on MSP430F5xx. ?I was wondering what is the minimal code I need to install on my micro to recognize the USB interface from PC. I am using this USB port just for firmware update. Thanks, john.


Help with installing mspgcc-20120406-p20120911 to W7

Started by Joe Bleaux in MSP43010 years ago 2 replies

What am I doing wrong or not doing at all? I want to use GCC free compiler for the MSP-430 family and especially for the TI Launchpad...

What am I doing wrong or not doing at all? I want to use GCC free compiler for the MSP-430 family and especially for the TI Launchpad MSP430F5529. I have never used GCC before. Also, where is a list of c commands for this processor? Thanks for any and all help. Joe


Problems with MSP430F2132

Started by Onestone in MSP43010 years ago 33 replies

This is probably just the usual issue with debounce of a switch (attaching the battery is a switch), and the system getting caught out....

This is probably just the usual issue with debounce of a switch (attaching the battery is a switch), and the system getting caught out. Typically you would have an INIT process shortly after start up with a clock stabilisation loop or similar. I don't know how you handle NMI's but typically if your NMI handling is too simplistic you will get a clock error, jump to the NMI which might the...


MSP430 GCC floating point libray for smaller code ?

Started by r_bo...@yahoo.com in MSP43010 years ago 10 replies
GCC

Hello, I have to modify code for an existing board with a 8 K MSP430 Series 1device. I'm using MSPGCC and Eclipse. The "old" code just...

Hello, I have to modify code for an existing board with a 8 K MSP430 Series 1device. I'm using MSPGCC and Eclipse. The "old" code just fits 8K. The new code doesn't, even with -os option. I assume the FP library consumes most of the memory space. Does anybody know if there is an other FP library for MSPGCC which delivers smaller code for Series 1 MSP430 devices ? Thank yo...


Re: BSL WITH MSP430F5437A

Started by "ant...@gmail.com" in MSP43010 years ago

--------------Boundary-00=_Q204WCW0000000000000 Content-Type: Text/Plain; charset="iso-8859-1" Content-Transfer-Encoding:...

--------------Boundary-00=_Q204WCW0000000000000 Content-Type: Text/Plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable =20 ;*********************** PROGRAM TRANSFER CODE ***************************= *** ;THE XFRCODE MUST BE MOVED FROM FLASH TO RAM AND THEN EXECUTED FROM RAM. = THIS ;CODE IS PART OF THE OBJECT CODE THAT WILL BE ERASED WHEN THE FLASH MEMORY= IS...


Ask a Question to the EmbeddedRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright


The 2024 Embedded Online Conference