Hi,

Anybody know if one can debug two MSP430's (in two comletely independent circuits, or their evaluation target boards, resp.) at the same time from CCE3.1 by attaching two of those USB devices?

CCE3.1 seems to support multi-target debugging but I'm unclear how to connect the hardware. A workaround would be using two PC's but I would like to avoid that.

Best regards, Klaus

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

I do not know if CCE3.1 supports multi-taget debugging, but I think Windows should be able to run multi-task and thus multiple copies of CCE3.1 independent of each other using different USB devices.

--- In m...@yahoogroups.com, "klausstrohhaecker" wrote:
>
> Hi,
>
> Anybody know if one can debug two MSP430's (in two comletely independent circuits, or their evaluation target boards, resp.) at the same time from CCE3.1 by attaching two of those USB devices?
>
> CCE3.1 seems to support multi-target debugging but I'm unclear how to connect the hardware. A workaround would be using two PC's but I would like to avoid that.
>
> Best regards, Klaus
>

------------------------------------

______________________________
Stellaris® MCU Family: New Parts, New Package, New Price.


(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

I have a dubt, I need to write a firmware in externa EEPROM TUSB for Virtua=
lCom application. I see that have any files .cfg and .bin.

Wich is the correct file? I=B4ve tested a few but no bouble a serial as ser=
ial...

tks,
Alessandro
=20

=09
=09
=09
=09
=09
=09
=09
=09
=09=20=09=09=20=09=20=20=20=09=09=20=20
_________________________________________________________________
Voc=EA sabia que pode acessar o Messenger direto do seu Hotmail? Descubra c=
omo!
http://www.microsoft.com/brasil/windows/windowslive/products/tutoriais.aspx

[Non-text portions of this message have been removed]

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Alessandro,

Where did you obtain the .cfg and .bin files from?

Regards,
John W.
On Thu, Oct 29, 2009 at 11:29 AM, Alesandro Correa w=
rote:

>
> I have a dubt, I need to write a firmware in externa EEPROM TUSB for
> VirtualCom application. I see that have any files .cfg and .bin.
>
> Wich is the correct file? I=B4ve tested a few but no bouble a serial as
> serial...
>
> tks,
>
> Alessandro
>
> __________________________________________________________
> Voc=EA sabia que pode acessar o Messenger direto do seu Hotmail? Descubra
> como!
> http://www.microsoft.com/brasil/windows/windowslive/products/tutoriais.as=
px
>
> [Non-text portions of this message have been removed]
>
>=20=20
>
[Non-text portions of this message have been removed]

------------------------------------

______________________________
Stellaris® MCU Family: New Parts, New Package, New Price.


(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Hi John,

Look for sllc297a, when you installed, these files are created in a Texas I=
nstruments folder. But, you should modify the PID/VID configurations for yo=
ur application. After, you should compiled this file for .bin extension.

Is what I Know?

Regards,
Alessandro
To: m...@yahoogroups.com
From: j...@westmorelandengineering.com
Date: Thu, 29 Oct 2009 14:05:27 -0700
Subject: Re: [msp430] Firmware for TUSB3410 (external I2C EEPROM)

=20

=20=20=20=20
Alessandro,

Where did you obtain the .cfg and .bin files from?

Regards,

John W.

On Thu, Oct 29, 2009 at 11:29 AM, Alesandro Correa w=
rote:

>

>

>

> I have a dubt, I need to write a firmware in externa EEPROM TUSB for

> VirtualCom application. I see that have any files .cfg and .bin.

>

> Wich is the correct file? I=B4ve tested a few but no bouble a serial as

> serial...

>

> tks,

>

> Alessandro

>

>

>

>

>

>

>

>

>

>

>

>

>

> __________________________________________________________

> Voc=EA sabia que pode acessar o Messenger direto do seu Hotmail? Descubra

> como!

> http://www.microsoft.com/brasil/windows/windowslive/products/tutoriais.as=
px

>

> [Non-text portions of this message have been removed]

>

>=20=20

>

[Non-text portions of this message have been removed]

=20

=20=20=20=20=20=20

=20=20=20=20
=20=20=20=20
=09
=09
=09
=09
=09
=09
=09=20=09=09=20=09=20=20=20=09=09=20=20
_________________________________________________________________
Voc=EA sabia que pode acessar o Messenger direto do seu Hotmail? Descubra c=
omo!
http://www.microsoft.com/brasil/windows/windowslive/products/tutoriais.aspx

[Non-text portions of this message have been removed]

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Thanks,

Yes, CCE itself can basically run in mulitple instances, albeit on different workspaces (not a problem here). I tried that but there are locking issues even with only one FET attached. For multi traget TI recommends runing two sessions inside one single CCE instance (that's what the help files say).

Next week I'll get the second FET-UIF and will try and report back if it works or not.

- Klaus
--- In m...@yahoogroups.com, "old_cow_yellow" wrote:
>
> I do not know if CCE3.1 supports multi-taget debugging, but I think Windows should be able to run multi-task and thus multiple copies of CCE3.1 independent of each other using different USB devices.
>
> --- In m...@yahoogroups.com, "klausstrohhaecker" wrote:
> >
> > Hi,
> >
> > Anybody know if one can debug two MSP430's (in two comletely independent circuits, or their evaluation target boards, resp.) at the same time from CCE3.1 by attaching two of those USB devices?
> >
> > CCE3.1 seems to support multi-target debugging but I'm unclear how to connect the hardware. A workaround would be using two PC's but I would like to avoid that.
> >
> > Best regards, Klaus
>

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

I run multiple instances using the elprotronic dll that supports up to 8 ta=
rgets.. I'm not sure if the multi dll comes with the free software but it d=
oes come with their interface..
=A0
I have used an elprotronic interface side by side with an olimex AND 2 ti f=
ets using their interface dll..
=A0
I don't run multiple work spaces simultaneously (I'm using crossworks but i=
t should=A0 work for CCE) I just switch to the=A0project I need.. I have 4 =
target boards hooded up to a networked computer which I run remotely for de=
bugging sessions..
=A0
--- On Fri, 10/30/09, klausstrohhaecker wrote:
From: klausstrohhaecker
Subject: [msp430] Re: Multiple Target Debugging with two MSP-FET430UIF's?
To: m...@yahoogroups.com
Date: Friday, October 30, 2009, 5:15 AM
=A0=20

Thanks,

Yes, CCE itself can basically run in mulitple instances, albeit on differen=
t workspaces (not a problem here). I tried that but there are locking issue=
s even with only one FET attached. For multi traget TI recommends runing tw=
o sessions inside one single CCE instance (that's what the help files say).

Next week I'll get the second FET-UIF and will try and report back if it wo=
rks or not.

- Klaus

--- In msp430@yahoogroups. com, "old_cow_yellow" wrot=
e:
>
> I do not know if CCE3.1 supports multi-taget debugging, but I think Windo=
ws should be able to run multi-task and thus multiple copies of CCE3.1 inde=
pendent of each other using different USB devices.
>=20
> --- In msp430@yahoogroups. com, "klausstrohhaecker" wr=
ote:
> >
> > Hi,
> >=20
> > Anybody know if one can debug two MSP430's (in two comletely independen=
t circuits, or their evaluation target boards, resp.) at the same time from=
CCE3.1 by attaching two of those USB devices?
> >=20
> > CCE3.1 seems to support multi-target debugging but I'm unclear how to c=
onnect the hardware. A workaround would be using two PC's but I would like =
to avoid that.
> >=20
> > Best regards, Klaus
>

[Non-text portions of this message have been removed]

------------------------------------

______________________________
Stellaris® MCU Family: New Parts, New Package, New Price.


(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )

Now I could not get it to work that way, but I managed to have multiple CCE=
instances running, each with it's own seperate workspace and dedicated tar=
get adapter. Selection of the target adapter's USB connection is via run-->=
debug...-->project_debug_session-->setup-->connection
There each workbench launch needs to connect to a different FET connection =
(one out of USB1...USB3 or LPT1...LPT3).

This solution pretty is OK for me, since cut&paste of code snippets etc acc=
ross the two workbenches is functional.

- Klaus
--- In m...@yahoogroups.com, Joe Radomski wrote:
>
> I run multiple instances using the elprotronic dll that supports up to 8 =
targets.. I'm not sure if the multi dll comes with the free software but it=
does come with their interface..
> =A0
> I have used an elprotronic interface side by side with an olimex AND 2 ti=
fets using their interface dll..
> =A0
> I don't run multiple work spaces simultaneously (I'm using crossworks but=
it should=A0 work for CCE) I just switch to the=A0project I need.. I have =
4 target boards hooded up to a networked computer which I run remotely for =
debugging sessions..
> =A0
>=20
>=20
> --- On Fri, 10/30/09, klausstrohhaecker wrote:
>=20
> From: klausstrohhaecker
> Subject: [msp430] Re: Multiple Target Debugging with two MSP-FET430UIF's?
> To: m...@yahoogroups.com
> Date: Friday, October 30, 2009, 5:15 AM
>=20
>=20
>=20
> Thanks,
>=20
> Yes, CCE itself can basically run in mulitple instances, albeit on differ=
ent workspaces (not a problem here). I tried that but there are locking iss=
ues even with only one FET attached. For multi traget TI recommends runing =
two sessions inside one single CCE instance (that's what the help files say=
).
>=20
> Next week I'll get the second FET-UIF and will try and report back if it =
works or not.
>=20
> - Klaus
>=20
> --- In msp430@yahoogroups. com, "old_cow_yellow" wr=
ote:
> >
> > I do not know if CCE3.1 supports multi-taget debugging, but I think Win=
dows should be able to run multi-task and thus multiple copies of CCE3.1 in=
dependent of each other using different USB devices.
> >=20
> > --- In msp430@yahoogroups. com, "klausstrohhaecker" =
wrote:
> > >
> > > Hi,
> > >=20
> > > Anybody know if one can debug two MSP430's (in two comletely independ=
ent circuits, or their evaluation target boards, resp.) at the same time fr=
om CCE3.1 by attaching two of those USB devices?
> > >=20
> > > CCE3.1 seems to support multi-target debugging but I'm unclear how to=
connect the hardware. A workaround would be using two PC's but I would lik=
e to avoid that.
> > >=20
> > > Best regards, Klaus
> > >

------------------------------------



(You need to be a member of msp430 -- send a blank email to msp430-subscribe@yahoogroups.com )