Goodmorning All,

I a new owner of a ooBoard with an ooPic. The board is working great, however i'm having a problem. I've tried to set the board in a different baud rate, which ( i guess ) went ok. However, tt this point i cannot communicate with the board anymore. So i tried to set the serial port back to the standard (9600) baudrate. As there is no communication possible, there is no way to do this. I've tried to reset the board, without succes. How can i reset the board that it goes to the default settings again? It is not possible to take the eeprom off the board.

Thanks for your help.
------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )

--- In o...@yahoogroups.com, jeroen_anslijn@... wrote:
>
> Goodmorning All,
>
> I a new owner of a ooBoard with an ooPic. The board is working
great, however i'm having a problem. I've tried to set the board in a
different baud rate, which ( i guess ) went ok. However, tt this point
i cannot communicate with the board anymore. So i tried to set the
serial port back to the standard (9600) baudrate. As there is no
communication possible, there is no way to do this. I've tried to
reset the board, without succes. How can i reset the board that it
goes to the default settings again? It is not possible to take the
eeprom off the board.
>
> Thanks for your help.
>

First of all, the chip automatically sets 9600,n,8,1 following reset.
Don't worry about it.

However, you probably have a "cosmic wedgie" where the OOPic is jammed
up. There is a schematic here:
http://www.roguerobotics.com/files/ooboard/documentation/OOBoard-100-A2-schem.jpg

Note the ESTOP pads in the upper left corner of the schematic.
Shorting these together, resetting the board and attempting to
download a program should be the same as removing the EEPROM.

ALWAYS put OOPic.delay=500 as the first executable statement. Use
=5000 for V6 of the IDE.

Richard

========================================================================
Groups related to oopic
========================================================================

SeattleRobotics (233 common members)
http://groups.yahoo.com/group/SeattleRobotics?v=1&t=ipt&ch=email&pub=groups&slk=aftr0&sec=recg
Mechanical/Robotics: The Seattle Robotics Society is a world wide group...

piclist (183 common members)
http://groups.yahoo.com/group/piclist?v=1&t=ipt&ch=email&pub=groups&slk=aftr1&sec=recg
Microprocessors/Microcontrollers: A discussion group for the PICMicro microcontrolle...

Robotics (130 common members)
http://groups.yahoo.com/group/Robotics?v=1&t=ipt&ch=email&pub=groups&slk=aftr2&sec=recg
Mechanical/Robotics: Robotics discussion group. This egroup is for thos...

rabbit-semi (119 common members)
http://groups.yahoo.com/group/rabbit-semi?v=1&t=ipt&ch=email&pub=groups&slk=aftr3&sec=recg
Microprocessors/Microcontrollers: This is a user group for folks designing and progr...

PARTS (107 common members)
http://groups.yahoo.com/group/PARTS?v=1&t=ipt&ch=email&pub=groups&slk=aftr4&sec=recg
Mechanical/Robotics: Portland Area Robotics Society is a club formed to...
------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )

Goodmorning All,
>
>I a new owner of a ooBoard with an ooPic. The board is working great, however i'm having a problem. I've tried to set the board in a different baud rate, which ( i guess ) went ok. However, tt this point i cannot communicate with the board anymore. So i tried to set the serial port back to the standard (9600) baudrate. As there is no communication possible, there is no way to do this. I've tried to reset the board, without succes. How can i reset the board that it goes to the default settings again? It is not possible to take the eeprom off the board.
>
>Thanks for your help.
>------------------------------------
>Hi Richard,

I've tried to reset the ooPic on the way you've descriped, however, no succes. It will still not communicate. Are there more ways to get it going again? Thanks, Harry
>

------------------------------------



(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )