Sign in
Search oopic
Subscribe to oopic
Ads
Discussion Groups
Discussion Groups | | OOPic B.2.2+'s
OOPic B.2.2+'s - tinslwc - May 8 17:29:01 2008
Are there any places that carry this firmware version for less than
$29.99? That is what Savage is selling the C's for. I am having
problems with the C's. Some code (excluding events, I can work around
those) will work fine on the B's but not on the C's. I cannot figure
it out so I just want to replace my C's with B's.
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )
$29.99? That is what Savage is selling the C's for. I am having
problems with the C's. Some code (excluding events, I can work around
those) will work fine on the B's but not on the C's. I cannot figure
it out so I just want to replace my C's with B's.
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )
Re: OOPic B.2.2+'s - rtstofer - May 9 0:06:49 2008
--- In o...@yahoogroups.com, "tinslwc" wrote:
>
> Are there any places that carry this firmware version for less than
> $29.99? That is what Savage is selling the C's for. I am having
> problems with the C's. Some code (excluding events, I can work around
> those) will work fine on the B's but not on the C's. I cannot figure
> it out so I just want to replace my C's with B's.
>
In the 40 pin DIP version, you might get some here:
http://www.junun.org/MarkIII/Info.jsp?item=29 or a controller (kit)
here: http://www.junun.org/MarkIII/Info.jsp?item=28
One nice thing about the Mark III controller is that it uses a real
RS232 level shifter. The 40 pin header is compatible with the OOPic S
board.
Richard
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )
>
> Are there any places that carry this firmware version for less than
> $29.99? That is what Savage is selling the C's for. I am having
> problems with the C's. Some code (excluding events, I can work around
> those) will work fine on the B's but not on the C's. I cannot figure
> it out so I just want to replace my C's with B's.
>
In the 40 pin DIP version, you might get some here:
http://www.junun.org/MarkIII/Info.jsp?item=29 or a controller (kit)
here: http://www.junun.org/MarkIII/Info.jsp?item=28
One nice thing about the Mark III controller is that it uses a real
RS232 level shifter. The 40 pin header is compatible with the OOPic S
board.
Richard
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )
Re: OOPic B.2.2+'s - tinslwc - May 11 17:26:36 2008
I make my own boards with RS232 using a ST232ACN which works great.
But I also have some other hardware on board for ethernet
communications. I use a Multiplexer to use one serial port with
several devices (RS232, RS485/422, as well as the TTL version). The
problem with the C's is that some of the code to setup the external
devices (mainly the Ethernet/IP co-processor) is not running
correctly or at all. That code works great on the B versions so I
will probably order some of those from below for $28 and it comes
with an EEPROM as well.
--- In o...@yahoogroups.com, "rtstofer" wrote:
>
> --- In o...@yahoogroups.com, "tinslwc" wrote:
> >
> > Are there any places that carry this firmware version for less
than
> > $29.99? That is what Savage is selling the C's for. I am having
> > problems with the C's. Some code (excluding events, I can work
around
> > those) will work fine on the B's but not on the C's. I cannot
figure
> > it out so I just want to replace my C's with B's.
> > In the 40 pin DIP version, you might get some here:
> http://www.junun.org/MarkIII/Info.jsp?item=29 or a controller (kit)
> here: http://www.junun.org/MarkIII/Info.jsp?item=28
>
> One nice thing about the Mark III controller is that it uses a real
> RS232 level shifter. The 40 pin header is compatible with the
OOPic S
> board.
>
> Richard
>
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )
But I also have some other hardware on board for ethernet
communications. I use a Multiplexer to use one serial port with
several devices (RS232, RS485/422, as well as the TTL version). The
problem with the C's is that some of the code to setup the external
devices (mainly the Ethernet/IP co-processor) is not running
correctly or at all. That code works great on the B versions so I
will probably order some of those from below for $28 and it comes
with an EEPROM as well.
--- In o...@yahoogroups.com, "rtstofer"
>
> --- In o...@yahoogroups.com, "tinslwc"
> >
> > Are there any places that carry this firmware version for less
than
> > $29.99? That is what Savage is selling the C's for. I am having
> > problems with the C's. Some code (excluding events, I can work
around
> > those) will work fine on the B's but not on the C's. I cannot
figure
> > it out so I just want to replace my C's with B's.
> > In the 40 pin DIP version, you might get some here:
> http://www.junun.org/MarkIII/Info.jsp?item=29 or a controller (kit)
> here: http://www.junun.org/MarkIII/Info.jsp?item=28
>
> One nice thing about the Mark III controller is that it uses a real
> RS232 level shifter. The 40 pin header is compatible with the
OOPic S
> board.
>
> Richard
>
------------------------------------
(You need to be a member of oopic -- send a blank email to oopic-subscribe@yahoogroups.com )