Sign in

username:

password:



Not a member?

Search piclist



Search tips

Subscribe to piclist



piclist by Keywords

12F675 | 16F628 | 16F84 | 16f877 | 16F877A | 16F88 | 18F458 | ADC | AVR | Bootloader | CAN | CCS | CRC | EAGLE | EEPROM | ICD | ICSP | IDE | JDM | LED | Macros | Microchip | MPLAB | PCB-CAD | PIC10F | Pic12f675 | PIC16F84 | PIC16F84A | PIC16F877 | PIC18 | PIC18F452 | PicBasic | PICC | PICSTART | PWM | RS-485 | RS232 | SMT | SPI | UART | USART | USB | Wireless | Wisp628 | Xilinx

Discussion Groups

Discussion Groups | Piclist | Ynt:RE: I don't programming that 18F458 and 12F675

A discussion group for the PICMicro microcontroller. Also called the Microchip PIC, this list is dedicated to the use and abuse of this fine, simple, microcontroller. Close to topic posts are welcome, ie. general electronics.

Ynt:RE: I don't programming that 18F458 and 12F675 - cnt - Jul 7 14:08:00 2003


yes, that version is supported. I'll try to connect PGM pin ground. > 1. Does that version of ic-prog support the chip types you are trying to > program? > 2. Do you pull the PGM pin low (assuming you use HVP)? > > Wouter van Ooijen > > -- ------------------------------------------- > Van Ooijen Technische Informatica: www.voti.nl > consultancy, development, PICmicro products > > > CNT TEK.

____________________________________________________________________________
Türkiye'nin en samimi arkadaş arama servisi ile hayatınıza renk katın! arkadasim.mynet.com





(You need to be a member of piclist -- send a blank email to piclist-subscribe@yahoogroups.com )

Ynt:RE: I don't programming that 18F458 and 12F675 - cnt - Jul 7 15:24:00 2003

I have been tring that pgm(rb5) pull down, but anything is changed. I put on PIC18F458 on my jdm programmer and open ic-prog v1.05A. I choose 18F458 on ic-prog. after that, if I don't change any setting and try to programming, the device successfully programming. but for example, I write a code in 0040H address and try to programming, the program alert me that "programming failed at code address 000040h!" it is possible that the ic-prog have a mistake? could you tell me please which software using you for 18F458 thanks >
> ----- Özgün İleti -----
> Kimden : "Wouter van Ooijen"
> Kime :
> Cc :
> Gönderme tarihi : Mon, 7 Jul 2003 20:11:00 +0200
> Konu : RE: [piclist] I don't programming that 18F458 and 12F675
>
> > I'm using a jdm programmer and ic-prog v1.05A. > > I try to programming 18F458 and 12F675 but I don't programming them > > 1. Does that version of ic-prog support the chip types you are trying to > program? > 2. Do you pull the PGM pin low (assuming you use HVP)? > > Wouter van Ooijen > > -- ------------------------------------------- > Van Ooijen Technische Informatica: www.voti.nl > consultancy, development, PICmicro products > > > CNT TEK.

__________________________
Türkiye'nin tercihi! Mynet Email





(You need to be a member of piclist -- send a blank email to piclist-subscribe@yahoogroups.com )

Ynt:RE: I don't programming that 18F458 and 12F675 - cnt - Jul 7 15:26:00 2003

I have been tring that pgm(rb5) pull down, but anything is changed. I put on PIC18F458 on my jdm programmer and open ic-prog v1.05A. I choose 18F458 on ic-prog. after that, if I don't change any setting and try to programming, the device successfully programming. but for example, I write a code in 0040H address and try to programming, the program alert me that "programming failed at code address 000040h!" it is possible that the ic-prog have a mistake? could you tell me please which software using you for 18F458 thanks >
> ----- Özgün İleti -----
> Kimden : "Wouter van Ooijen"
> Kime :
> Cc :
> Gönderme tarihi : Mon, 7 Jul 2003 20:11:00 +0200
> Konu : RE: [piclist] I don't programming that 18F458 and 12F675
>
> > I'm using a jdm programmer and ic-prog v1.05A. > > I try to programming 18F458 and 12F675 but I don't programming them > > 1. Does that version of ic-prog support the chip types you are trying to > program? > 2. Do you pull the PGM pin low (assuming you use HVP)? > > Wouter van Ooijen > > -- ------------------------------------------- > Van Ooijen Technische Informatica: www.voti.nl > consultancy, development, PICmicro products > > > CNT TEK.

__________________________
Türkiye'nin tercihi! Mynet Email




(You need to be a member of piclist -- send a blank email to piclist-subscribe@yahoogroups.com )

RE: RE: I don't programming that 18F458 and 12F675 - Wouter van Ooijen - Jul 7 15:53:00 2003

Message
>  could you tell me please which software using you for 18F458 thanks 
 
http://www.voti.nl/wisp628
http://www.voti.nl/xwisp
 
But that won't help you much with your hardware...
 

Wouter van Ooijen

-- -------------------------------------------
Van Ooijen Technische Informatica: www.voti.nl
consultancy, development, PICmicro products
 

 




(You need to be a member of piclist -- send a blank email to piclist-subscribe@yahoogroups.com )