I'm not 100% sure if it is for this setup but have a look at the
dmaeth100_network_mode() function in dmaeth100.lib. This allows you set the mode
to the different combinations.
Regards,
Peter
--- In r..., "tomborkin" wrote: >
> Hi Peter,
>
> I'm having some trouble getting consistent performance out of an RCM5750.
We have attached our own RJ-45, Halo SO55N2, and filter circuit.
>
> I was wondering if there was a way to set it to 10Base-T only. I'm not
concerned about speed but I was wondering if running it at a lower speed may be
more 'solid'. I don't understand too much about the PHY
Interfaces etc. Using the oscilloscope all the signals are comparable to a
working Ethernet connection (on the RCM Interface Board). The switch it's
plugged into lights up to indicate the presence of the connection but traffic
doesn't seem to pass in and out of the chip. I had it working for a golden
20mins and have left the set up the same. I'm keen to try pulling it back
to 10M if that would help.
>
> Regards,
>
> Tom
>
> --- In r..., "petermcs" wrote:
> >
> > Hi Jeff,
> >
> > The Rabbit modules that say 10/100Base-T are fully compatible and will talk
100Mb/s if connected to a switch, hub or other device that also supports 100BT.
The interface usuallly auto negotitates the appropriate maximum rate that the
partners mutually support (there are also issues of full duplex vs half duplex
and flow control methods that are negotitated not just the bit rates). Some
smart switches can be told to only use certain combinations, which will allow
for those hopefully rare occasions when auto negotiation falls flat on its
face.
> >
> > It is possible that some newer networking equipment could have
interoperability problems with 10Mbs equipment but I don't know if it is
all that common (I could imagine that some designers are so caught up with
thinking about 100/1000/10000 technology and forget that there are many millions
of embedded devices - and older PCs - that still only talk the lowly 10Mbs).
> >
> > I still find 10Mbs hubs usefull when debugging network comms as they allow
you to see all the comms between the devices without having to set up mirrored
ports or network taps which require more expenseive equipment (100Mbs hubs are
around as well but are even more rare than 10Mbs ones).
> >
> > Even though many of the Rabbit devices support 100Mbs as, you point out they
will never be in danger of using all that bandwidth (although the new RCM6700
might have a better chance at pulling that feat off!).
> >
> > Regards,
> > Peter
> > Regards,
> > Peter
> > --- In r..., "Jeffrey" wrote:
> > >
> > > Hi!
> > >
> > > Many of the Rabbit modules say 10/100Base-T. 10Base-T is a maximum of
10Mb/S (10 megabits per second) and 100Base-T is 100Mb/s. But are the modules
just "compatible" with 100BT or is there a way to actually select 10 or 100?
> > >
> > > I have a hub that can tell if a device I plug into it is 10 or 100BT but
I'm not sure how it does that. I'm also pretty sure the back of my PC
has a different color LED on the ethernet jack if it's doing 10 or 100.
> > >
> > > I'm asking because I have a potential client that asked me to
design something to upgrade their current 10BT product to 100BT. The speed
isn't the issue (not much data to send back and forth) so I'm guessing
they want to integrate the product in a fully 100BT network?
> > >
> > > Thanks,
> > >
> > > Jeff
> > >
>
Reply by tomborkin●June 28, 20122012-06-28
Hi Peter,
I'm having some trouble getting consistent performance out of an RCM5750.
We have attached our own RJ-45, Halo SO55N2, and filter circuit.
I was wondering if there was a way to set it to 10Base-T only. I'm not
concerned about speed but I was wondering if running it at a lower speed may be
more 'solid'. I don't understand too much about the PHY
Interfaces etc. Using the oscilloscope all the signals are comparable to a
working Ethernet connection (on the RCM Interface Board). The switch it's
plugged into lights up to indicate the presence of the connection but traffic
doesn't seem to pass in and out of the chip. I had it working for a golden
20mins and have left the set up the same. I'm keen to try pulling it back
to 10M if that would help.
Regards,
Tom
--- In r..., "petermcs" wrote: >
> Hi Jeff,
>
> The Rabbit modules that say 10/100Base-T are fully compatible and will talk
100Mb/s if connected to a switch, hub or other device that also supports 100BT.
The interface usuallly auto negotitates the appropriate maximum rate that the
partners mutually support (there are also issues of full duplex vs half duplex
and flow control methods that are negotitated not just the bit rates). Some
smart switches can be told to only use certain combinations, which will allow
for those hopefully rare occasions when auto negotiation falls flat on its
face.
>
> It is possible that some newer networking equipment could have
interoperability problems with 10Mbs equipment but I don't know if it is
all that common (I could imagine that some designers are so caught up with
thinking about 100/1000/10000 technology and forget that there are many millions
of embedded devices - and older PCs - that still only talk the lowly 10Mbs).
>
> I still find 10Mbs hubs usefull when debugging network comms as they allow you
to see all the comms between the devices without having to set up mirrored ports
or network taps which require more expenseive equipment (100Mbs hubs are around
as well but are even more rare than 10Mbs ones).
>
> Even though many of the Rabbit devices support 100Mbs as, you point out they
will never be in danger of using all that bandwidth (although the new RCM6700
might have a better chance at pulling that feat off!).
>
> Regards,
> Peter
> Regards,
> Peter
> --- In r..., "Jeffrey" wrote:
> >
> > Hi!
> >
> > Many of the Rabbit modules say 10/100Base-T. 10Base-T is a maximum of
10Mb/S (10 megabits per second) and 100Base-T is 100Mb/s. But are the modules
just "compatible" with 100BT or is there a way to actually select 10 or 100?
> >
> > I have a hub that can tell if a device I plug into it is 10 or 100BT but
I'm not sure how it does that. I'm also pretty sure the back of my PC
has a different color LED on the ethernet jack if it's doing 10 or 100.
> >
> > I'm asking because I have a potential client that asked me to design
something to upgrade their current 10BT product to 100BT. The speed isn't
the issue (not much data to send back and forth) so I'm guessing they want
to integrate the product in a fully 100BT network?
> >
> > Thanks,
> >
> > Jeff
>
Reply by petermcs●June 23, 20102010-06-23
Hi Jeff,
The Rabbit modules that say 10/100Base-T are fully compatible and will talk
100Mb/s if connected to a switch, hub or other device that also supports 100BT.
The interface usuallly auto negotitates the appropriate maximum rate that the
partners mutually support (there are also issues of full duplex vs half duplex
and flow control methods that are negotitated not just the bit rates). Some
smart switches can be told to only use certain combinations, which will allow
for those hopefully rare occasions when auto negotiation falls flat on its
face.
It is possible that some newer networking equipment could have interoperability
problems with 10Mbs equipment but I don't know if it is all that common (I
could imagine that some designers are so caught up with thinking about
100/1000/10000 technology and forget that there are many millions of embedded
devices - and older PCs - that still only talk the lowly 10Mbs).
I still find 10Mbs hubs usefull when debugging network comms as they allow you
to see all the comms between the devices without having to set up mirrored ports
or network taps which require more expenseive equipment (100Mbs hubs are around
as well but are even more rare than 10Mbs ones).
Even though many of the Rabbit devices support 100Mbs as, you point out they
will never be in danger of using all that bandwidth (although the new RCM6700
might have a better chance at pulling that feat off!).
Regards,
Peter
Regards,
Peter
--- In r..., "Jeffrey" wrote: >
> Hi!
>
> Many of the Rabbit modules say 10/100Base-T. 10Base-T is a maximum of
10Mb/S (10 megabits per second) and 100Base-T is 100Mb/s. But are the modules
just "compatible" with 100BT or is there a way to actually select 10 or 100?
>
> I have a hub that can tell if a device I plug into it is 10 or 100BT but
I'm not sure how it does that. I'm also pretty sure the back of my PC
has a different color LED on the ethernet jack if it's doing 10 or 100.
>
> I'm asking because I have a potential client that asked me to design
something to upgrade their current 10BT product to 100BT. The speed isn't
the issue (not much data to send back and forth) so I'm guessing they want
to integrate the product in a fully 100BT network?
>
> Thanks,
>
> Jeff
>
Reply by Jeffrey●June 22, 20102010-06-22
Hi!
Many of the Rabbit modules say 10/100Base-T. 10Base-T is a maximum of 10Mb/S
(10 megabits per second) and 100Base-T is 100Mb/s. But are the modules just
"compatible" with 100BT or is there a way to actually select 10 or 100?
I have a hub that can tell if a device I plug into it is 10 or 100BT but
I'm not sure how it does that. I'm also pretty sure the back of my PC
has a different color LED on the ethernet jack if it's doing 10 or 100.
I'm asking because I have a potential client that asked me to design
something to upgrade their current 10BT product to 100BT. The speed isn't
the issue (not much data to send back and forth) so I'm guessing they want
to integrate the product in a fully 100BT network?