Emulator in Comp.Arch.Embedded
Comp.Arch.Embedded is a worldwide Usenet news group that is used to discuss various aspects of Embedded Systems development.
We found 131 threads matching "Emulator"
You are looking at page 1 of 4.
The most relevant threads are listed first
So far in May, you have voted 0 times ou of a total of 20 votes by the community.
Please help us clean the archives from unuseful discussion threads by using the voting system! Details here.
djordj - 2007-05-31 17:14:00
I can't connect to a PDS51 (with serial cable), the software says that
there is no emulator connected to the COM port!!!
Is there anybody that knows this emulator?
I need help...
Thanks
...
I'm goint to debug ARM7TDMI using TI XDS510PP-Plus JTAG emulator. I
want to know if it is possible to use XDS510 JTAG emulator under
ADS(Arm Development Suite) environment.
Do I need some drivers?
Please, Help me.
...
123music - 2009-10-08 10:11:00
Hello,
I am using XDS510 USB emulator.
I am able to reset my emulator but unable to detect it.
Getting below error in sdconfig
** Checking for a valid emulator/eZdsp
$$ You are connected to:
$$ EmuProductName=XDS510USB
$$ EmuPortAddr=0x510
$$ EmuPortMode=USB
$$ ProductId=5...
Hi,
I am trying to find a JTAG emulator for a new project which uses a
ARM7 processor. I am considering several vendors, such as Lauterbach
(Trace32 ICD), Macraigor (Wiggler, Raven, usbDemon, mpDemon), Emutec
(DebugJet), Hitex (Tantino), Embest, Nohau, EPI, SigNum, ...etc. The
emulator ha...
I would like to rent or buy (1 month period) an in-circuit emulator for the
Intel 80C186XL processor. I need it for about 1 month. Doers someone have
one they could rent me or sell or could you refer me to a company that
carries them. The manufacturer of the emulator is unimportant.
thank you
...
paras sharma - 2007-04-28 10:26:00
Hello to every one;
I am a engineering student & for my
satisfaction I am trying to develop a loader to load a own made
program (which is a emulator) at boot time. My moto is to make a CD-
ROM emulator so that the ISO (of any OS stored in HDD) can be run to
instal...
Started by Unknown 7 years ago
I have a board using a 25MHz 80C186EB and I'm looking for an in circuit
emulator that will allow the following:
Stepping through codestream instruction by instruction
That is it. I want to yank the CPU off the nonfunctional board, drop a
socket, hook up the emulator and step through exactly...
Started by
pipi 9 years ago
Hi,
Where can I get a atmel 89c52 emulator ,or development kit, with a
reasonable price? Thanks,
Pipi
...
Hi,
I am looking for a low cost 27xxx eprom emulator. Please advice me on
which one I should get.
Thanks
Nathan
...
Hi,
for maintainance of a 68000 PLCC or DIP based board I'm looking to get an
emulator or something else to load my code quickly into RAM. Sorry, I can't
use any ROM monitor solutions since I don't know less about resource
occupation. Even a used part and any hint where to get it is appreciate...
Please suggest good emulator for 8051/8052 which support ISP
devices(Atmel AT89S series)
Thanks
Naimesh
...
WYSIWYG - 2005-11-25 12:17:00
Hello,
Its time for an EPROM emulator. I would prefer USB, > 1MBit, fast down load,
Win2k/XP compatible tools, ...
I have googled for an hour now, but the i386EX family does not seem to
have a jtag emulator/debugger available.
Is this true ??
hamilton
...
Chris H - 2008-04-01 07:42:00
Hi ,
I am looking for a Renesas M16c/M32C M3A-0665 FoUSB emulator
I know it has been superseded by the E8A but for particular reasons we
need the M16c/M32C M3A-0665 FoUSB emulator and it's software. renesas
do not have any left. I have tried them
so if any one, preferably UK based has ...
I need to find an emulator or some other way to support an old 80c51fa
product. I already have an assembler (an old Avocet ava51.exe) that
works ok. I need a way to step through this code and see the source
code and symbols. What is the best way to do this? The program is
written only in assembl...
So if I was to think about writing an arm emulator for fun, which core
family should I choose? I see that there are rt system and application
cores (and secure). The benefits of each in terms of application are
obvious. Are the rt systems averse to letting you write an operating
system on top?
...
TXMarsh - 2010-09-30 20:36:00
Does anyone have an emulator for a 2716 eprom that they no longer have
a use for?
In the alternative, does anyone know if anyone is still making these?
Thanks.
Tim
...
New2MSP430 - 2006-06-30 14:28:00
What I mean by a software emulator is, an application that runs on a
desktop/laptop where some favor of MSP430 code can be run and tested,
as if it was running on the actual chip.
Hope that makes sence.
...
sekar - 2007-05-10 01:35:00
Hi I am new to ARM. I have a aac decoder which i run in arm. It is
working fine and it is perfectly matching. But the performance numbers
between simulator and emulator differs widely.
In Simulator it is around 20Mcycles. But when i run the same in
emulator it takes around 10 to 20 times highe...
djordj - 2009-04-20 17:50:00
I'm looking for an 8051 emulator, as my Brendes Biceps-V has gone
away...
Thanks
...
Started by
vic 9 years ago
Hello everybody,
could someone explain to me what a JTAG Emulator is and what is used for?
Thanks in advance.
...
joolzg - 2011-05-24 04:11:00
Anybody got a simple 8052 emulator in C source, im trying to reverse engineer
some code and would like to emulate/simulate the code to get a better
understanding as it looks like it was written in C and compiled by a very bad
compiler
joolz
--
--------------------------------- ---...
Looking for recommendations on a JTAG programmer / emulator for a
product under development.
The target processor is a TI TMS320F2812 DSP, and the software is
written using TI's Code Composer's Studio V2.2
Thanks,
Roberto Waltman.
[ Please reply to the group,
return address i...
adonis - 2006-11-12 08:14:00
I have been using these JTAG emulators for ADSP blackfin processors for
quite some time now. I want to know about how the software breakpoint
actually works internally. I opened the ADSP JTAG emulator, it had a
BF531 DSP and a flash inside. Now, if my understanding is right... When
we run the co...
Started by Unknown 7 years ago
I found this store from eBay and purchased an XDS510 USB JTAG Emulator
recently, it works well and the key is it's cheaper than others. Just
recommend and hopefully it's useful. Good luck!
http://stores.ebay.com/Embedded-Development-Tools
...
Started by Unknown 6 years ago
hi!
I am a senior student in computer science. In our senior design course,
we are supposed to develop a pic emulator for the card that is used in
embedded course in our department. This card uses 16F877 pic.
Since we're not experienced in this area, we don't know what should a
pic emulator ha...
Jose Tango - 2012-01-04 03:24:00
Does anyone have or know where I might obtain the DOS based software
for Nohau
EMUL51-PC?
I still have the emulator with serial box, cable and various pods, and
a PC with
a serial port that will boot into DOS. Somewhere along the way the
software
distribution diskette got tossed.
Never t...
Tom Lucas - 2007-03-02 12:11:00
I'm currently looking at replacing the processor in a safety critical
system from an 80188 to likely some form of ARM.
I'd been told that this might be tricky because approvals houses (mainly
TUV and GasTec) like to step through the code on an in-circuit emulator
rather than stepping throug...
leilei - 2009-02-16 03:32:00
Hi, it there any good Emulator for PPC?
...
alb - 2012-02-08 10:00:00
Dear all,
I found an interesting 'Engineer to Engineer Note' on AD
(http://www.analog.com/static/imported-files/application_notes/6187549521220
6ee_34.pdf) on the booting process when the ez-ice is connected to the
target device.
I was wondering if there is a similar note on the 'loading...
Hi,
Is it possible to use the AVR s/w emulator on AVRStudio running on a PC and
somehow get external control signals (serial or parallel port) that would
correspond to signals produced by an actual AVR?
The reason I'm asking is that I have to design a small scale electromechanical
elevato...
Hi,
I am using a JTAG based emulator, but as I could see the JTAG emulator
can not give what we want when we are looking for very complex bugs,
it has a limited trace buffer and we can not set watch pointers,
etc...
The conclusion is that we have to have a better tool, but it is being
diff...
Not Really Me - 2010-10-30 12:41:00
Have a need for a piece of history?
I have an Applied Microsystems EM-180B Z80 emulator. Fully static, allows
single stepping
w/pod, user manual and carry case.
Make an offer. email below.
scott
validated software
com
__________ Information from ESET NOD32 Antivirus, version o...
Started by
Lee 9 years ago
Dear all,
What is the difference between development board and emulator?What are
they used for?
Thanks,
...
JSambrook - 2006-10-13 12:48:00
Hello,
I'm looking for a flash emulator that will support the 64MB
P33 NOR flash from Intel, part # RC48F4400P0TB00 (leaded) or
PC48F4400P0TB00 (lead free).
By flash emulator, I mean an active device that can take the
place of the flash part in circuit, uses RAM to emulate the
flash memory...
Johnson - 2010-08-18 16:29:00
Hi there,
We are porting a windows application from desktop into embedded Linux on
Atmel AT91 ARM Cores, thus we need JTAG to debug the firmware under a
Linux environment. However, SAM-ICE only connects via USB to a PC
running Microsoft Windows2000 or XP. So I am looking for a JTAG emulator...
john11w - 2012-04-15 22:52:00
I've developed a nice business over the past 15 years lately using the
89lpc92x family of parts. The DIP (20) package is important so that
upgrades may be made in the field. Yearly volume is 3-5K parts. Yes, boards
are assembled by hand using through hole parts. I support 5 part timers and
still use...
After several intsruments built with the 6805, I'm looking to upgrade
to a more modern processor with more code space and RAM, as well as
more modern debugging schemes. The 6808 series seems to fit the bill,
specifically the GP32 chip.
One of my biggest hangups about the 6805 is the ancient an...
Hello All,
I am using IAR Embedded Work bench C/C++ compiler for MSP 430 devices. I
would like to program the fuse of MSP430 chip using JTAG interface. I
studied from MSP 430 Embedded Workbench User guide, which directed me to
use the 'Secure' option in the Emulator menu after downloading the
Sof...
Hervé - 2005-06-09 09:01:00
Hi,
We are going to buy a new environment for a new uC.
Actually, we are using a Fujitsu 16 bits (MB90F94x).
What do you think of the HCS12X family from Motorola ? Does anyone have some
bad (/good) experience with it ?
Our dealer suggest us the CodeWarrior IDE from MetroWerks for HCS12
(co...