Autonomous vehicle - design questions to ponder

Ed Nutter January 27, 2016

When designing an autonomous or remotely-controlled vehicle, there are a few factors to take into consideration. Three of these are purpose, environment, and terrain.

What is the purpose of the vehicle?

Will it be used in an industrial setting with people moving around it that it must not run over?

Will it be used in a hazardous environment, like Fukushima or Chernobyl, where it would be exposed to high levels of radiation and must be cleaned or left behind? If it must be left behind, any...


Steering an autonomous vehicle - two basic ways

Ed Nutter January 15, 2016

While there are many types of steering mechanisms, for now, I will be concentrating on two of them.

The first is known as Ackerman-type steering. On a rear-wheel-drive four-wheeled car, the rear wheels push the vehicle while the two front wheels pivot left and right, either by using a servo or a geared motor, to steer the vehicle.  Understeer is when the vehicle tries to push through the turn too wide, possibly causing the vehicle to drive off the outside of the course.   ...


A quick look at the Line Follower Vehicle

Ed Nutter January 3, 20162 comments

In its most basic form, a Line Following Vehicle (LFV) consists of a line sensor, a vehicle, some way to process the signal, and batteries.

A basic line can consist of black 3/4" electrical tape on a white background. Other lines consist of a white line on a black background. While usually solid, a line can consist of dashes and even change between colors. Turns are generally sweeping and gradual, but can include angles. Each of these changes adds a layer of difficulty to the...


Mounting plate for Arduino

Ed Nutter November 30, 2015

While having a breadboard with your microcontroller is necessary, it is very cumbersome if the two aren't fastened together somehow.  You can buy mounting plates, but I choose to make one.

I am using thin plexiglass type glazing material from the hardware store.  You can use the thicker material, but may have to purchase longer screws for stand-offs depending on what you use.

I like using the small Plano tackle boxes, because they can hold the plate, a few parts, batteries and a...


Basic hand tools for electronics assembly

Ed Nutter November 20, 20153 comments

Though the software tools vary with different microcontrollers, many hardware tools are the same.

If you are working on larger robotic or automotive systems, you will need a 3/8" and 1/2" drive socket set. There are occasions when even larger drive socket sets are needed. For small robots and taking things apart, the 1/4" drive socket set is useful. The sizes usually range from 5/32" to 9/16" and 4mm to 15mm.  You will need both shallow and deep sockets, both standard and...


Choosing a Vehicle

Ed Nutter May 25, 20163 comments

There are a few things to take into consideration when choosing a vehicle or chassis for your autonomous vehicle. You can design and build your own, buy a stripped robot chassis, or use a radio controlled (RC) vehicle as a starting point. I usually use an RC vehicle as a starting point.

Two basic styles of RC vehicles exist. The first, is the toy-grade vehicle. It can be found in most retail stores, and usually costs below 50 dollars. Its main advantage is the low price, which can be as low...


It ain't heavy, it's my robot...

Ed Nutter January 3, 2017

Unmanned Ground Vehicles - Design considerations for man-portable/packable vehicles

A UGV is “a ground based mechanical device that can sense and interact with its environment.” (Carlson, How)

A Field Robot is expected to work outdoors, though generally not in rain or snow, including rough terrain, dirt and dust. (Carlson, Reliability)

A Man-portable robot weighs less than 40 pounds, or is capable of being broken down into subassemblies for two soldiers weighing less than 40...


Steering an autonomous vehicle - two basic ways

Ed Nutter January 15, 2016

While there are many types of steering mechanisms, for now, I will be concentrating on two of them.

The first is known as Ackerman-type steering. On a rear-wheel-drive four-wheeled car, the rear wheels push the vehicle while the two front wheels pivot left and right, either by using a servo or a geared motor, to steer the vehicle.  Understeer is when the vehicle tries to push through the turn too wide, possibly causing the vehicle to drive off the outside of the course.   ...


A quick look at the Line Follower Vehicle

Ed Nutter January 3, 20162 comments

In its most basic form, a Line Following Vehicle (LFV) consists of a line sensor, a vehicle, some way to process the signal, and batteries.

A basic line can consist of black 3/4" electrical tape on a white background. Other lines consist of a white line on a black background. While usually solid, a line can consist of dashes and even change between colors. Turns are generally sweeping and gradual, but can include angles. Each of these changes adds a layer of difficulty to the...


Autonomous vehicle - design questions to ponder

Ed Nutter January 27, 2016

When designing an autonomous or remotely-controlled vehicle, there are a few factors to take into consideration. Three of these are purpose, environment, and terrain.

What is the purpose of the vehicle?

Will it be used in an industrial setting with people moving around it that it must not run over?

Will it be used in a hazardous environment, like Fukushima or Chernobyl, where it would be exposed to high levels of radiation and must be cleaned or left behind? If it must be left behind, any...