Someday We’ll Find It, The Kelvin Connection

Jason Sachs July 28, 20142 comments

You’d think it wouldn’t be too hard to measure electrical resistance accurately. And it’s really not, at least according to wikiHow.com: you just follow these easy steps:

  • Choose the item whose resistance you wish to measure.
  • Plug the probes into the correct test sockets.
  • Turn on the multimeter.
  • Select the best testing range.
  • Touch the multimeter probes to the item you wish to measure.
  • Set the multimeter to a high voltage range after finishing the...

Lost Secrets of the H-Bridge, Part IV: DC Link Decoupling and Why Electrolytic Capacitors Are Not Enough

Jason Sachs April 29, 20147 comments

Those of you who read my earlier articles about H-bridges, and followed them closely, have noticed there's some unfinished business. Well, here it is. Just so you know, I've been nervous about writing the fourth (and hopefully final) part of this series for a while. Fourth installments after a hiatus can bring bad vibes. I mean, look what it did to George Lucas: now we have Star Wars Episode I: The Phantom Menace and


How to Analyze a Differential Amplifier

Jason Sachs April 13, 2014

There are a handful of things that you just have to know if you do any decent amount of electronic circuit design work. One of them is a voltage divider. Another is the behavior of an RC filter. I'm not going to explain these two things or even link to a good reference on them — either you already know how they work, or you're smart enough to look it up yourself.

The handful of things also includes some others that are a little more interesting to discuss. One of them is this...


Another 10 Circuit Components You Should Know

Jason Sachs October 30, 20131 comment

It's that time again to review all the oddball goodies available in electronic components. These are things you should have in your bag of tricks when you need to design a circuit board. If you read my previous posts and were looking forward to more, this article's for you!

1. Bus switches

I can't believe I haven't mentioned bus switches before. What is a bus switch?

There are lots of different options for switches:

  • mechanical switch / relay: All purpose, two...

Short Takes (EE Shanty): What shall we do with a zero-ohm resistor?

Jason Sachs October 19, 20132 comments

In circuit board design you often need flexibility. It can cost hundreds or thousands of dollars to respin a circuit board, so I need flexibility for two main reasons:

  • sometimes it's important to be able to use one circuit board design to serve more than one purpose
  • risk reduction: I want to give myself the option to add in or leave out certain things when I'm not 100% sure I'll need them.

And so we have jumpers and DIP switches and zero-ohm resistors:

Jumpers and...


Layout recomendations and tips for best performance against EMC

Dr. Maykel Alonso January 4, 2013

When making the layout of the circuit diagram, it is interesting to perform a preliminary analysis of several issues in order to minimize problems arising from electromagnetic compatibility.The analysis consists in:

Identify / Analyze components: This section will analyze the integrated components, as well as any recommendations it may have the manufacturer. We must also analyze the encapsulation possibilities which have the component.


A Useful Current Profiling Method

Dr Cagri Tanriover July 2, 20123 comments

In one of my recent projects, I had to capture the dynamic current profile of a short-range wireless embedded platform for a number of operation scenarios. Due to the dynamic nature of the current consumption involved, I was unable to use a standard voltmeter for this job. On the time axis, I needed a minimum resolution of 1 millisecond and the accuracy of the current measurement was supposed to be better than 2 mA. This task would be a piece of cake with a Digital Storage...


First Steps in OrCAD 16 [Capture]

Dr. Maykel Alonso June 1, 20127 comments

Hello community, I know that in last posts I have been writting about the Software. But what about Hardware? In last months I have been dealing with it, exactly with OrCAD 16. And I will explain how to build a PCB  in 2 articles. For begginers could be a good and easy guide.

This article explains the part for the designing of the schematic, and in the next one which i will explain the layout part.

The first stuff you must known about OrCAD is that it is not an unique tool for...


Have You Ever Seen an Ideal Op-Amp?

Jason Sachs April 30, 2012

Somewhere, along with unicorns and the Loch Ness Monster, lies a small colony of ideal op-amps. Op-amp is short for operational amplifier, and we start our education on them by learning about these mythical beasts, which have the following properties:

  • Infinite gain
  • Infinite input impedance
  • Zero output impedance

And on top of it all, they will do whatever it takes to change their output in order to make their two inputs equal.

But they don't exist. Real op-amps have...


Hot Fun in the Silicon: Thermal Testing with Power Semiconductors

Jason Sachs April 20, 2012

Here's a trick that is useful the next time you do thermal testing with your MOSFETs or IGBTs.

Thermal testing?!

Yes, that's right. It's important to make sure your power transistors don't overheat. In the datasheet, you will find some information that you can use to estimate how hot the junction inside the IC will get.

Let's look at an example. Here's a page from the IRF7739 DirectFET datasheet. I like this datasheet because it has almost all the thermal stuff on one page,...


Another 10 Circuit Components You Should Know

Jason Sachs October 30, 20131 comment

It's that time again to review all the oddball goodies available in electronic components. These are things you should have in your bag of tricks when you need to design a circuit board. If you read my previous posts and were looking forward to more, this article's for you!

1. Bus switches

I can't believe I haven't mentioned bus switches before. What is a bus switch?

There are lots of different options for switches:

  • mechanical switch / relay: All purpose, two...

10 More (Obscure) Circuit Components You Should Know

Jason Sachs February 5, 20121 comment

The interest in my previous article on obscure but useful electronics parts, "10 Circuit Components You Should Know" was encouraging enough that I thought I would write a followup. So here are another 10:

1. "Ideal Diode" controllers

Load-sharing circuits use diodes tied together at their cathode terminal to take the most positive voltage among the sources and connect it to a load. Works great: you have a DC/DC power supply, a battery, and a solar cell, and it will use whichever output is...


Real-time clocks: Does anybody really know what time it is?

Jason Sachs May 29, 20118 comments

We recently started writing software to make use of a real-time clock IC, and found to our chagrin that the chip was missing a rather useful function, namely elapsed time in seconds since the standard epoch (January 1, 1970, midnight UTC).Let me back up a second.A real-time clock/calendar (RTC) is a micropower chip that has an oscillator on it that keeps counting time, independent of main system power. Usually this is done with a lithium battery that can power the RTC for years, so that even...


R1C1R2C2: The Two-Pole Passive RC Filter

Jason Sachs July 28, 20181 comment

I keep running into this circuit every year or two, and need to do the same old calculations, which are kind of tiring. So I figured I’d just write up an article and then I can look it up the next time.

This is a two-pole passive RC filter. Doesn’t work as well as an LC filter or an active filter, but it is cheap. We’re going to find out a couple of things about its transfer function.

First let’s find out the transfer function of this circuit:

Not very...


Someday We’ll Find It, The Kelvin Connection

Jason Sachs July 28, 20142 comments

You’d think it wouldn’t be too hard to measure electrical resistance accurately. And it’s really not, at least according to wikiHow.com: you just follow these easy steps:

  • Choose the item whose resistance you wish to measure.
  • Plug the probes into the correct test sockets.
  • Turn on the multimeter.
  • Select the best testing range.
  • Touch the multimeter probes to the item you wish to measure.
  • Set the multimeter to a high voltage range after finishing the...

Stairway to Thévenin

Jason Sachs December 31, 2011

This article was inspired by a recent post on reddit asking for help on Thévenin and Norton equivalent circuits.

(With apologies to Mr. Thévenin, the rest of the e's that follow will remain unaccented.)

I still remember my introductory circuits class on the subject, roughly as follows:

(NOTE: Do not get scared of what you see in the rest of this section. We're going to point out the traditional approach for teaching linear equivalent circuits first. If you have...


The Other Kind of Bypass Capacitor

Jason Sachs January 3, 20173 comments

There’s a type of bypass capacitor I’d like to talk about today.

It’s not the usual power supply bypass capacitor, aka decoupling capacitor, which is used to provide local charge storage to an integrated circuit, so that the high-frequency supply currents to the IC can bypass (hence the name) all the series resistance and inductance from the power supply. This reduces the noise on a DC voltage supply. I’ve...


Have You Ever Seen an Ideal Op-Amp?

Jason Sachs April 30, 2012

Somewhere, along with unicorns and the Loch Ness Monster, lies a small colony of ideal op-amps. Op-amp is short for operational amplifier, and we start our education on them by learning about these mythical beasts, which have the following properties:

  • Infinite gain
  • Infinite input impedance
  • Zero output impedance

And on top of it all, they will do whatever it takes to change their output in order to make their two inputs equal.

But they don't exist. Real op-amps have...


Optimizing Optoisolators, and Other Stories of Making Do With Less

Jason Sachs December 14, 20144 comments

It’s been a few months since I’ve rolled up my sleeves here and dug into some good old circuit design issues. I started out with circuit design articles, and I’ve missed it.

Today’s topic will be showing you some tricks for how to get more performance out of an optoisolator. These devices — and I’m tempted to be lazy and call them “optos”, but that sounds more like a cereal with Greek yogurt-covered raisins — are essentially just an LED...


Voltage Drops Are Falling on My Head: Operating Points, Linearization, Temperature Coefficients, and Thermal Runaway

Jason Sachs January 19, 2015

Today’s topic was originally going to be called “Small Changes Caused by Various Things”, because I couldn’t think of a better title. Then I changed the title. This one’s not much better, though. Sorry.

What I had in mind was the Shockley diode equation and some other vaguely related subjects.

My Teachers Lied to Me

My introductory circuits class in college included a section about diodes and transistors.

The ideal diode equation is...