How Embedded Linux is used in Spacecrafts !
This article dives into the application of Linux in spacecraft, examining the challenges it poses and proposing potential solutions. Real-life examples will be discussed, while also addressing the drawbacks of employing Linux in safety-critical missions.
Getting Started With Zephyr: Bluetooth Low Energy
In this blog post, I show how to enable BLE support in a Zephyr application. First, I show the necessary configuration options in Kconfig. Then, I show how to use the Zephyr functions and macros to create a custom service and characteristic for a contrived application.
Using GPIO in (Apache) NuttX RTOS
Blinking an LED is the embedded Hello World, and this tutorial walks through using GPIOs on NuttX running on a Raspberry Pi Pico. It shows how to enable the GPIO driver and example in menuconfig, build and flash the nuttx.uf2, and use NSH gpio device files to read and write pins. The post also explains polling versus interrupt-driven inputs and the pull-up/edge setup needed for button interrupts.
Optimizing Real-Time Operating Systems for Efficient Edge Devices
Edge devices need real-time responsiveness but run on tight CPU, memory, and power budgets. This post breaks down what an RTOS brings to the edge: deterministic task scheduling, lean memory management, protocol support, and modular scalability, then tackles common challenges like synchronization and security. Read it for practical best practices on scheduling and protocols plus a look at future trends such as edge AI integration and interoperable infrastructure.
Embedded Developer’s New Year’s Resolution
Use the holiday pause to turn vague intentions into a practical embedded skills plan for the coming year. This post lays out concrete resolutions: adopt modern software design practices, pick up a modern language like C++ or Rust, and learn when to use RTOS, cooperative schedulers, or Zephyr. Small, focused improvements will pay off across firmware projects.
Getting Started With Zephyr: Writing Data to EEPROM
In this blog post, I show how to implement a Zephyr application to interact with EEPROM. I show how the Zephyr device driver model allows application writers to be free of the underlying implementation details. Unfortunately, the application didn't work as expected, and I'm still troubleshooting the cause.
Getting Started with NuttX RTOS on Three Low Cost Boards
You can get Linux-like power on cheap microcontroller boards using NuttX, not a full Linux system. This article walks through building and flashing NuttX on three low-cost targets: Raspberry Pi Pico (RP2040), ESP32-DevKitC, and STM32F4Discovery, covering SDKs, toolchains, and serial access. Follow the provided commands to configure, compile, and connect to the NuttShell so you can start experimenting with NuttX quickly.
Getting Started With Zephyr: Saving Data To Files
In this blog post, I show how to implement a Zephyr application to mount a microSD card, create a new file on the microSD card, and write data to it. The lessons learned from such an application can be helpful for devices out in the field that need to write data to off-board memory periodically, especially in cases where Internet access may be sporadic.
Open-Source Licenses Made Easy with Buildroot and Yocto for Embedded Linux
In this article I will try to explain what are the copyrights/copyleft, what are the popular opensource software licenses, and how to make sure that your Embedded Linux system complies with them using popular build systems ; Buildroot or YOCTO projec
Getting Started With Zephyr: Devicetree Overlays
In this blog post, I show how the Devicetree overlay is a valuable construct in The Zephyr Project RTOS. Overlays allow embedded software engineers to override the default pin configuration specified in Zephyr for a particular board. In this blog post, I use I2C as an example. Specifically, I showed the default I2C pins used for the nRF52840 development kit in the nominal Zephyr Devicetree. Then, I demonstrated how an overlay can be used to override this pin configuration and the final result.
Surprising Linux Real Time Scheduler Behavior
An embedded Linux data acquisition project ran into puzzling UART latency whenever heavy UI animations ran. Moving all app threads to SCHED_FIFO helped but did not eliminate delays. After reading about kernel worker thread interactions, Matthew moved the UI back to the normal scheduler and the jitter vanished. The post highlights an unexpected kernel level priority inversion risk and a pragmatic workaround.
OS influence on power consumption
Power consumption of an embedded system may be influenced in software in general, but selection of an operating system can be key.
Round-robin or RTOS for my embedded system
Manuel Herrera walks through the practical tradeoffs between bare-metal round-robin loops and adopting an RTOS for embedded projects. He outlines two round-robin styles, explains how an RTOS gives independent threads and synchronization primitives, and highlights added code, licensing, interrupt latency, and the learning curve. Read this to sharpen decision criteria around timing guarantees, reuse, and whether an RTOS truly adds value to your firmware.
What is “real time”?
The post clarifies the technical meaning of “real time” for embedded systems and contrasts it with the colloquial sense of immediacy. It presents a precise definition: a real-time system’s correctness depends on both logical results and the time at which those results are produced, so missing timing constraints constitutes failure. The article emphasizes determinism — low variance in operation timing — as the key property of real-time systems, and contrasts classic RTOS behavior with general-purpose Linux’s higher timing variance. It also notes that raw CPU overprovisioning can mask nondeterminism in some designs, but is not always practical, reinforcing that real time means predictable timing sufficient for the application, not simply “fast.”
Getting Started With Zephyr: Devicetree Bindings
This blog post shines some light on how devicetrees are used in The Zephyr Project. Specifically, we understand the mechanisms that enable us to use nodes in the devicetree in the C source files. We use a sample provided in the Zephyr repository itself and work our way through portions of the Zephyr codebase to get insight into the mechanisms that make this possible.
From bare-metal to RTOS: 5 Reasons to use an RTOS
Most developers default to bare-metal, but Jacob Beningo argues an RTOS often simplifies modern embedded design. He outlines five practical reasons to move to an RTOS: easier integration of connectivity stacks and GUIs, true preemptive scheduling with priorities, tunable footprints, API-driven portability, and a common toolset for tasks and synchronization. The piece helps decide when RTOS adoption speeds development.
How to use I2C devices in (Apache) NuttX: Scanning for Devices
Hands-on guide to scanning I2C peripherals on NuttX using a Raspberry Pi Pico, showing how the RTOS exposes i2c master instances and the i2ctool. The article walks through where the RP2040 I2C driver lives, how to enable I2C0 in menuconfig, build and flash nuttx, and run the i2c dev command to probe the bus. Verify sensors like BMP280 or SSD1306 before registering drivers.
Getting Started With Zephyr: Devicetrees
This blog post provides an introduction to the "Devicetree", another unique concept in The Zephyr Project. We learn about the basic syntax of a device tree and how its structure and hierarchy mirror hardware, from the SoC to the final board. We also see how hardware described in a devicetree can be referenced and controlled in the source code of a Zephyr-based application.
Using GPIO in (Apache) NuttX RTOS
Blinking an LED is the embedded Hello World, and this tutorial walks through using GPIOs on NuttX running on a Raspberry Pi Pico. It shows how to enable the GPIO driver and example in menuconfig, build and flash the nuttx.uf2, and use NSH gpio device files to read and write pins. The post also explains polling versus interrupt-driven inputs and the pull-up/edge setup needed for button interrupts.
Choosing a Microcontroller for Your Vehicle
Picking the right microcontroller can make or break an autonomous vehicle project, and this post gives a practical checklist to help. It walks through voltage and power needs, memory and IO planning, cost and availability tradeoffs, and when to step up from an 8-bit MCU to a 32-bit controller or single-board computer. Real-world board examples illustrate the choices.
Getting Started With Zephyr: Saving Data To Files
In this blog post, I show how to implement a Zephyr application to mount a microSD card, create a new file on the microSD card, and write data to it. The lessons learned from such an application can be helpful for devices out in the field that need to write data to off-board memory periodically, especially in cases where Internet access may be sporadic.
Embedded Programming Video Course Shows How OOP Works Under the Hood
Want to see how OOP actually maps to machine level code? This free video course walks through encapsulation, inheritance, and polymorphism with hands-on comparisons between C and C++. You will inspect C implementations, compiler-generated code, and debug traces, and learn how encapsulation relates to RTOS concurrency. The polymorphism lesson reverses the usual order to expose runtime costs and previews implementing polymorphism in C.
Modern Embedded Systems Programming: Beyond the RTOS
Blocking-based RTOS tasks make embedded systems brittle and hard to extend, this post argues, and presents a practical alternative: active objects organized as message pumps. It explains why one-blocking-call tasks and nonblocking event handlers improve responsiveness and reduce task proliferation, and recommends using frameworks plus hierarchical state machines and UML to enforce good architecture and make designs scalable.
You Don't Need an RTOS (Part 3)
In this third article I'll share with you a few cooperative schedulers (with a mix of both free and commercial licenses) that implement a few of the OS primitives that the "Superduperloop" is currently missing, possibly giving you a ready-to-go solution for your system. On the other hand, I don't think it's all that hard to add thread flags, binary and counting semaphores, event flags, mailboxes/queues, a simple Observer pattern, and something I call a "marquee" to the "Superduperloop"; I'll show you how to do that in the second half of this article and the next. Although it will take a little more work than just using one of the projects above, it will give you the maximum amount of control over your system and it will let you write tasks in ways you could only dream of using an RTOS or other off-the-shelf system.
How to install Ubuntu 12.04 Precise, Xubuntu-desktop and Open JDK-7 on Beagleboard Rev. C2
Want to run Java GUI apps on a BeagleBoard Rev C2? This hands-on post walks through installing Ubuntu 12.04, adding the Xubuntu desktop, and getting OpenJDK-7 running, including SD flashing, u-boot and network setup, display and audio tweaks, and a fix for XFCE login ownership problems. Follow the exact commands and small workarounds the author used to get a monitor, sound, and Java VM working on the board.
Getting Started with NuttX RTOS on Three Low Cost Boards
You can get Linux-like power on cheap microcontroller boards using NuttX, not a full Linux system. This article walks through building and flashing NuttX on three low-cost targets: Raspberry Pi Pico (RP2040), ESP32-DevKitC, and STM32F4Discovery, covering SDKs, toolchains, and serial access. Follow the provided commands to configure, compile, and connect to the NuttShell so you can start experimenting with NuttX quickly.
Getting Started With Zephyr: Devicetrees
This blog post provides an introduction to the "Devicetree", another unique concept in The Zephyr Project. We learn about the basic syntax of a device tree and how its structure and hierarchy mirror hardware, from the SoC to the final board. We also see how hardware described in a devicetree can be referenced and controlled in the source code of a Zephyr-based application.
Choosing a Microcontroller for Your Vehicle
Picking the right microcontroller can make or break an autonomous vehicle project, and this post gives a practical checklist to help. It walks through voltage and power needs, memory and IO planning, cost and availability tradeoffs, and when to step up from an 8-bit MCU to a 32-bit controller or single-board computer. Real-world board examples illustrate the choices.
BusyBox; The Swiss Army Knife of Embedded Linux
In this article we cover the BusyBox, how it's designed to be optimized for embedded targets, and how to configure and build it in different ways, we also covered the license and limitation, which led to the development of ToyBox, I hope you enjoyed the article, please leave a comment for any correction or suggestions.
Getting Started With Zephyr: Writing Data to EEPROM
In this blog post, I show how to implement a Zephyr application to interact with EEPROM. I show how the Zephyr device driver model allows application writers to be free of the underlying implementation details. Unfortunately, the application didn't work as expected, and I'm still troubleshooting the cause.
