Introduction to Microcontrollers - Hello World
Mike Silva walks through the classic embedded hello world by blinking an LED on both an AVR and an STM32. The tutorial covers GPIO configuration, bit manipulation, simple software delay loops, and common pitfalls such as compiler optimizations that can remove empty delays unless you use volatile. Practical wiring tips and debugging advice with a scope make this an ideal first lab for embedded engineers.
Introduction to Microcontrollers - Further Beginnings
Mike Silva walks through the CPU plumbing every embedded engineer needs to know before writing their first LED blinky. The post explains registers (data, address, stack pointer, link), the fetch-execute cycle, and the main instruction classes such as arithmetic, logic, shifts, branches, and call/return mechanics. Read this to see how C maps to CPU operations and why stack versus link register choices matter.
Introduction to Microcontrollers - Beginnings
Mike Silva's beginner tutorial series walks through core microcontroller concepts and practical steps to get started, from wiring an LED blinky to understanding startup code. He compares embedded and desktop programming, explains why C and assembly matter, and introduces AVR and STM32 Cortex-M3 toolchains and hardware. Expect clear examples, no-nonsense tool advice, and the essential hardware knowledge to move from simulator to a real board.
Essential Elements to choose a right Processor
Choosing the right processor can feel overwhelming, especially after a project with many viable parts. In this post Sathyanarayana Hadadi condenses practical criteria into a usable checklist for embedded designers, covering speed, hardware accelerators, peripherals, memory, power, security, availability, and tooling. Read on to turn a long shortlist into a confident selection and avoid costly redesigns.
Intro to Microcontrollers Part 2: AVR Microcontrollers
This follow-up explores getting an AVR Dragon working with an ATtiny24A, covering the necessary cables, BOM choices, and Atmel Studio setup. It walks through firmware updates, an ADC-based internal temperature sensor example using reduced-noise ADC and ISR handling, and practical debugging tips including debugWire versus ISP and high-voltage recovery. Expect candid hardware caveats like weak drive strength and 5V power quirks.
Mounting plate for Arduino
While having a breadboard with your microcontroller is necessary, it is very cumbersome if the two aren't fastened together somehow. You can buy mounting plates, but I choose to make one.
Blinkenlights 2.0
Nothing spells old movie computers like a panel of randomly blinking lights, but in fact, these so-called "blinkenlights" can be valuable indicators - especially in embedded systems where the user interface must be minimal, small and cheap. Control of these lights can be achieved using a very simple, real-time interpreted script, and this kind of solution may be extended to other and more complex embedded tasks.
Improving the Reload2 active load
Fabien Le Mentec takes a low-cost Reload2 active load and turns it into a programmable test tool. By swapping the manual setpoint for a Teensy 3.1 DAC and replacing the op-amp with a chopper amplifier, he gets software-controlled current profiles and lowers the minimum load current to about 7 mA. It is a practical hack for testing power supplies and Ethernet-powered boards under realistic startup and sleep conditions.
Intro to Microcontrollers Part 2: AVR Microcontrollers
This follow-up explores getting an AVR Dragon working with an ATtiny24A, covering the necessary cables, BOM choices, and Atmel Studio setup. It walks through firmware updates, an ADC-based internal temperature sensor example using reduced-noise ADC and ISR handling, and practical debugging tips including debugWire versus ISP and high-voltage recovery. Expect candid hardware caveats like weak drive strength and 5V power quirks.
Make Your Own MCU Boards (2023 Teardown Conference)
Ditch the development boards! Products like the Nucleo development boards serve a wonderful purpose, but they’re ill-suited for projects that need to be small and cheap, such as hobby projects or products just beginning a production run. In this talk (a recording from the 2023 Teardown Conference), you’ll learn how to put a microcontroller or other custom circuit on a PCB a little larger than a stick of gum for less than $3 a board.
Mounting plate for Arduino
While having a breadboard with your microcontroller is necessary, it is very cumbersome if the two aren't fastened together somehow. You can buy mounting plates, but I choose to make one.
My friend, the compiler
Modern compilers were given great powers, but we don't always know where and when they'll use them. This may cause us to either worry needlessly or trust unjustifiably, as demonstrated by a little example in this post.
Blinkenlights 2.0
Nothing spells old movie computers like a panel of randomly blinking lights, but in fact, these so-called "blinkenlights" can be valuable indicators - especially in embedded systems where the user interface must be minimal, small and cheap. Control of these lights can be achieved using a very simple, real-time interpreted script, and this kind of solution may be extended to other and more complex embedded tasks.
Essential Elements to choose a right Processor
Choosing the right processor can feel overwhelming, especially after a project with many viable parts. In this post Sathyanarayana Hadadi condenses practical criteria into a usable checklist for embedded designers, covering speed, hardware accelerators, peripherals, memory, power, security, availability, and tooling. Read on to turn a long shortlist into a confident selection and avoid costly redesigns.
Intro to Microcontrollers Part 2: AVR Microcontrollers
This follow-up explores getting an AVR Dragon working with an ATtiny24A, covering the necessary cables, BOM choices, and Atmel Studio setup. It walks through firmware updates, an ADC-based internal temperature sensor example using reduced-noise ADC and ISR handling, and practical debugging tips including debugWire versus ISP and high-voltage recovery. Expect candid hardware caveats like weak drive strength and 5V power quirks.
