Automatic generated Build-Number

Started by Roth Markus in 68HC1214 years ago 2 replies

Gentlemen I am about to re-setup the whole build process of our system with the Metrowerks IDE, target: HC12D60A. ...

Gentlemen I am about to re-setup the whole build process of our system with the Metrowerks IDE, target: HC12D60A. Question: I want to integrate an build number that counts up automatic. This number should be automatic generated and integrated in the code, at a cer


Problems programing flash on M68KIT912DP256 with BDM Multilink/Metrowerks

Started by djsimpson100 in 68HC1216 years ago 3 replies

Hi all, I am having problems programming the flash on the MC9S912DP256. I am using Codewarrior HC12 V1.2 and the P&E BDM...

Hi all, I am having problems programming the flash on the MC9S912DP256. I am using Codewarrior HC12 V1.2 and the P&E BDM Multilink which came with the Motorola M68KIT912DP256. If I load the Fibo Flash example, the debugger stalls at at the 60% mark in execu


Re: Metrowerks UNION problem.

Started by fred in 68HC1214 years ago 22 replies

Try Instead of the following HANDLE Vobjects[10]; prio = Vobjects[0]->Task.priority; ....THIS union...

Try Instead of the following HANDLE Vobjects[10]; prio = Vobjects[0]->Task.priority; ....THIS union virtualtasks { struct VTASK Task; struct VEVENT Pend; }; union virtualtasks Vobjects[10]; void main()


Quad core programming problem

Started by Jonathan Masters in 68HC1210 years ago 2 replies

Hi all. I am experimenting with moving my PE+METROWERKS setup to a quad core Intel machine. Metroworks can be made to work and compile my...

Hi all. I am experimenting with moving my PE+METROWERKS setup to a quad core Intel machine. Metroworks can be made to work and compile my project. I can then connect to the target with a USB-ML-12 and it appears to program the device. Any attempt to actually run the target yields in either: i) The programming works, but the HIWAVE debugger showing the program running off the rails...


How to convert my *.abs to *.s19 file

Started by uripeled2000 in 68HC1216 years ago 2 replies

Hi I am developing software for the MC9S12DG256BCPV using the 9s12256 model 112 utility board and the Metrowerks CodeWarrior V2...

Hi I am developing software for the MC9S12DG256BCPV using the 9s12256 model 112 utility board and the Metrowerks CodeWarrior V2 after make I get DG256B_ProcessorExpert_P&E.abs. How to convert this file into *.s19 file in order to be able to download it to my utility Boar


cual es mejor y mas sencvillo de usar e intuitivo

Started by yel1232003 in 68HC1215 years ago

hello: Ilooking a good bdm debugger and ide for hc12 flash .some people send me your experiencies for trial one. nohau, isystem...

hello: Ilooking a good bdm debugger and ide for hc12 flash .some people send me your experiencies for trial one. nohau, isystem ,albatron pemicro , metrowerks, cosmic , trace 32 and your cost appz thans NECESITO QUE ME ORIENTEIS QUE IDE ESMEJOR MAS SENCILLO EINTUI


Restoring the Serial Monitor on 9s12c32 with CW 2.1, 3 or 4.5

Started by aerowesty2000 in 68HC1212 years ago

Could anyone tell me how to load the serial monitor back onto a 9S12C32 MCU using Metrowerks Codewarrior and a P&E BDM. I am familiar with...

Could anyone tell me how to load the serial monitor back onto a 9S12C32 MCU using Metrowerks Codewarrior and a P&E BDM. I am familiar with developing C programs on CW 2, 3, 4.5 for the 9S12dp256 But, have not done any assy programming. We have a blank 9S12C32 in which we want to load the serial monitor. How do I restore the serial monitor, where do I get it, how do I configure CW to...


CodeWarrior 6.1 debugger | HC9S12E128 breakpoints don't work

Started by Tim Perry in 68HC1214 years ago 1 reply

Environment: Windows XP Metrowerks Code Warrior Dev Studio 3.1 Real-Time Debugger 6.1 uController: HC9S12E128 Language: C &...

Environment: Windows XP Metrowerks Code Warrior Dev Studio 3.1 Real-Time Debugger 6.1 uController: HC9S12E128 Language: C & C++ Problem: I get the message "Cannot set hardware breakpoint at address " on all lines of code.


Newbie question / Processor Expert

Started by Tim Perry in 68HC1215 years ago

My environment is Metrowerks 3.0 w/ Processor Expert w/ 9s12E uProc I am trying to use the TimerInt Bean. The "Installed...

My environment is Metrowerks 3.0 w/ Processor Expert w/ 9s12E uProc I am trying to use the TimerInt Bean. The "Installed Beans Overview" indicates that TimerInt is available but TimerInt doesn't show up in the "Bean Selector". Can anyone give me a


need instructions on how to dowload C program to test on Minidragon MC9S12DP256B

Started by Shah O Dayan in 68HC1213 years ago 1 reply

Dear friends, I am in dire need of some help - this might be very simple for most of you. But I am a newbie and need help. I have written my...

Dear friends, I am in dire need of some help - this might be very simple for most of you. But I am a newbie and need help. I have written my program in C. I am trying to download the C program written with Codewarrior Metrowerks Developer Studio. I am trying to download and test my program on to a MC9S12DP256B minidragon HCS12 chip. The software I have (which I don't know how to use) is ...


Banked Program - JSR and CALL in the same code

Started by Killingsworth, Steve in 68HC1215 years ago 4 replies

I have code that was configured to run in FLAT mode (SMALL memory model) on a DG128A using Metrowerks CodeWarrior. I am...

I have code that was configured to run in FLAT mode (SMALL memory model) on a DG128A using Metrowerks CodeWarrior. I am trying to convert it to run in BANKED mode and have run into a problem. I have some legacy in-line asm code that is not tolerant to the CALL/RTC


Codewarrior - processor expert - Generate PRM file

Started by in 68HC1216 years ago

Hello, I am working on a project with a MC9S12A128B processor with Metrowerks Codewarrior and processor expert V2.00 ...

Hello, I am working on a project with a MC9S12A128B processor with Metrowerks Codewarrior and processor expert V2.00 (special edition). In order to declare variables and structures in EEPROM area I have added a new segment for the EEPROM in the .prm file


Re: What address format for 9S12X?

Started by Daniel Friederich in 68HC1211 years ago

Hi John, The draft v3.0 of the m8-16eabi ABI does support both banked and global addresses, and as far as I know both Cosmic and Metrowerks...

Hi John, The draft v3.0 of the m8-16eabi ABI does support both banked and global addresses, and as far as I know both Cosmic and Metrowerks are following it. BTW: How does GCC12 encode addresses? Daniel John Hartman (NoICE) wrote: > Does anyone know how 9S12X addresses appear in elf/dwarf > files? Banked? Global? > > Long ago, Motorola recommended the use of "linear" address fo


processor expert & writing flash memory

Started by David Relson in 68HC1213 years ago 9 replies

Greetings, I'm using Metrowerks CodeWarrior 3.1 with Processor Expert to develop an embedded boot loader for an MC9S12A64 (64k flash)....

Greetings, I'm using Metrowerks CodeWarrior 3.1 with Processor Expert to develop an embedded boot loader for an MC9S12A64 (64k flash). It needs to write to multiple pages, for example addresses 3C8000 ff and 3D8000 ff. After writing to 3C8000, the 3D8000 write is failing because bank changing isn't happening. As best I can tell, in datapage.c


HCS12 1K79X mask, Code works with debug stmts, doesn't without

Started by varneybob in 68HC1216 years ago 4 replies

Okay, I have roughly 4000 lines of C++ code developed in Metrowerks CodeWarrior for the STAR12. The code seems to work fine for the...

Okay, I have roughly 4000 lines of C++ code developed in Metrowerks CodeWarrior for the STAR12. The code seems to work fine for the most part as long as my serial port debug messages are active. My serial debug messages are polled out and not interrupt driven. As soon as I recomp


Hiware compiler, Star12, and linear addressing

Started by Alexandre Plombin in 68HC1216 years ago 1 reply

Hi, Has anyone had issues working with linear addressing on the Star12 DP256, generating a true linear s-record (0x0C.0000 to...

Hi, Has anyone had issues working with linear addressing on the Star12 DP256, generating a true linear s-record (0x0C.0000 to 0x0F.FFFF ... thanks Gordon!) with the Hiware (hum, Metrowerks) compiler? It seems that Hiware is using the linear addresses during symbol resulution at lin


Metrowerks LinkError. I don't understand the help (or the error).

Started by Paul Johnson in 68HC1216 years ago 2 replies

I am getting the following link error: Link Error : L1907: Fixup overflow in handleCancel, to putAbort type 3, at offset 0x27 ...

I am getting the following link error: Link Error : L1907: Fixup overflow in handleCancel, to putAbort type 3, at offset 0x27 The help says: L1907 Fixup overflow in , type at offset
Description An il


Does P&E MULTILINK load code to EEPROM?

Started by G in 68HC1213 years ago 1 reply

I use a Adapt9S12E128 board in a testing project. I am using Metrowerks Code Warrior - CW12V3.1. My code is working right when P&E MULTILINK...

I use a Adapt9S12E128 board in a testing project. I am using Metrowerks Code Warrior - CW12V3.1. My code is working right when P&E MULTILINK connected with a PC. However, system will be reseted at once when unpluging P&E MULTILINK. Advise please. Is P&E MULTILINK able to load code to EEPROM? Thanks