hi, i am using at91SAM 9263EK eval board (Rev B). I have compiled the linux kernel 2.6.30 with at91 patches. was able to create uImage using...

hi, i am using at91SAM 9263EK eval board (Rev B). I have compiled the linux kernel 2.6.30 with at91 patches. was able to create uImage using mkimage.bin the board has 8MB dataflash and a NAND flash. now that while doing some experiment with SAM-BA, I erased both NAND and data flash. If i restart the board, I see "ROMBoot > " on the serial debug console. any info on how to bring the board

Hi I was using at91sam9263ek board, so far I flashed kernel and u-boot on dataflash and file system on nand flash 16 bit its working fine (...

Hi I was using at91sam9263ek board, so far I flashed kernel and u-boot on dataflash and file system on nand flash 16 bit its working fine ( atmel board) now I want to shift the kernel -2.6.24 and u-boot( 1.1.5 ) to nand flash ( 16bit) I have a problem after I cross compiled( for Arm ) and flashed to nand. the following is the debug info I found, while flashing I do set the environmen...

Hi all, I'm having problems reading and writing the external flash of the AT91RM9200-EK that uses an AT49BV6416 with IAR. - First of all,...

Hi all, I'm having problems reading and writing the external flash of the AT91RM9200-EK that uses an AT49BV6416 with IAR. - First of all, I haven't been able to find more information about the JLink, as I'm not so sure that the debugger will allow me at all to read / write in memory, the same memory in where all the debug information seats. - I have used the initialization sugges...

Hi all, I wonder what is the NAND flash you use in a design with an at91sam7s parts ? Size, brand etc... We are looking to put 1 Nand on...

Hi all, I wonder what is the NAND flash you use in a design with an at91sam7s parts ? Size, brand etc... We are looking to put 1 Nand on our design but this is the first time we do this. We have always put dataflash and not nand. Regards jonathan ------------------------------------

Hi, I'm trying to read JEDEC from my serial FLASH, but I keep getting wrong id. I tested LLB and MISO/MOSI hard loop, both get me proper data....

Hi, I'm trying to read JEDEC from my serial FLASH, but I keep getting wrong id. I tested LLB and MISO/MOSI hard loop, both get me proper data. Can somebody enlight me where I'm making mistake? This is my code: PMC_EnablePeripheral(AT91C_ID_PIOA); //turn on PIOA peripheral PIO_Configure(spi_pins, PIO_LISTSIZE(spi_pins)); //conf MISO,MOSI,SPCK,NPCS PMC_EnablePeripheral...

Hello, Im not an expert in embedded coding and am in somewhat of a hurry to get a brownout detection project out of the way and have been stuck...

Hello, Im not an expert in embedded coding and am in somewhat of a hurry to get a brownout detection project out of the way and have been stuck trying to set and clear the General-purpose NVM bits in the embedded flash controller. The processor Im using is the AT91SAM7x256. I need to be able to set and clear the GPNVM bits 0 and 1 as I desire. However I was once able to set the bits and now am n...

Hi all...... I am using AT91SAM7x256 in my hardware to communicate with PC. Priviously I was using AT91SAM7X512,when its internal flash...

Hi all...... I am using AT91SAM7x256 in my hardware to communicate with PC. Priviously I was using AT91SAM7X512,when its internal flash was erased the device used to enumerate successfully........ I have now changed AT91SAM7X512 with AT91SAM7X256, but now when its internal flash is erased, host is not able enumerate the device. ------------------------------------

Hello, Several times before also, when I was preparing some programs which are based on the software examples for AT91SAM7x, I used to...

Hello, Several times before also, when I was preparing some programs which are based on the software examples for AT91SAM7x, I used to get following error: arm-elf-gcc -g -nostartfiles -Wl,--gc-sections -T"../at91lib/boards/at91sam7x-ek/at91sam7x512/flash.lds" -o bin/templat e-project-at91sam7x-ek-at91sam7x512-flash.elf obj/flash_board_cstartup.o obj/flash_main.o obj/flash_stdio.o obj/...

When I send a read status command to an AT25F2048 SPI serial flash, I always get 0xFF as the status. I did send a write enable command...

When I send a read status command to an AT25F2048 SPI serial flash, I always get 0xFF as the status. I did send a write enable command right after my register inits. Any ideas? Thanks.

I have a board I'm just starting to bring up (using an AT91SAM7S256) for which I have an arm-elf executable I'd like to flash using the IAR ...

I have a board I'm just starting to bring up (using an AT91SAM7S256) for which I have an arm-elf executable I'd like to flash using the IAR J-link tools. Using the IAR example flasher I can flash the flasher executable itself so the cpu seems happy enough on my board. But, my code is all build using arm-elf-gcc and I'd rather not switch to IAR (well, t

IAR's flash loader could download SIM file into the internal flash. But it seems to be that you must have the D79 file either. My progject is...

IAR's flash loader could download SIM file into the internal flash. But it seems to be that you must have the D79 file either. My progject is built into Bin file by ADS. And it could be translated to SIM file. But how to download the sim file without d79 file? Kidman ------------------------ Yahoo! Groups Sponsor --------------------~--> Yahoo! Groups gets a make over. See the new e

Hi. I am a new member to this group. I have a board designed around AT91SAM7SE32 with an external 2 MB flash and 4 MB RAM. Could anyone please...

Hi. I am a new member to this group. I have a board designed around AT91SAM7SE32 with an external 2 MB flash and 4 MB RAM. Could anyone please tell me - which is the suitable FREE RTOS that can work on this processor? Also, can there be a JFFS2 like file system support in the suggested RTOS? Your reply will be highly appreciated. Thanks, Mansij ------------------------------------ ...

Hi everyone! I would like to use a SerialFlash (AT25/AT26) for my bootsrap as well as for u-boot storage. The SAM-BA applets are able to...

Hi everyone! I would like to use a SerialFlash (AT25/AT26) for my bootsrap as well as for u-boot storage. The SAM-BA applets are able to identify, enable and erase the flash I'm using now (M25P16-VMP6G). Even sending of the bootstrap works - meaning it is executed after reset and therefore obviously transferred in some way. But while transferring any data, the SAM-BA freezes and has to be...

Does anyone know of a Borland Delphi example for writing to flash using the SAM-BA dll? I'm guessing not but figured it was worth a try to...

Does anyone know of a Borland Delphi example for writing to flash using the SAM-BA dll? I'm guessing not but figured it was worth a try to ask. Since (for some reason) Atmel decided to make AT91Boot_DLL.dll into a COM component, it's not very straightforward to port it to another environment (yes, I realize it can be done but I'm not a COM superstar - especially in Delphi). I have to u...

Hi ! My web-page with jtag tools for SAM7S is upgraded. It contains a flash programmer, a gdb server and directions for making a cheap USB...

Hi ! My web-page with jtag tools for SAM7S is upgraded. It contains a flash programmer, a gdb server and directions for making a cheap USB jtag adapter. Check http://kjell.e.andersen.googlepages.com/ -kjell eirik

I want to communicate with a SPI serial flash. I've seen enough code to initialize the SPI port. However, I can't find any sample code that...

I want to communicate with a SPI serial flash. I've seen enough code to initialize the SPI port. However, I can't find any sample code that will show me how to tx and rx bytes in page mode. In the AT91_CDROM, I see a file called : AT91M55800A-BasicSPI-GHS3_6-2_0.zip Can I re-use some of the code for the SAM7S64? Are the SPI registers the

Hello, I made a similar post on the e-embedded yahoo group. I know that ucLinux was ported to the AT91. I would like to know how much of an...

Hello, I made a similar post on the e-embedded yahoo group. I know that ucLinux was ported to the AT91. I would like to know how much of an operating system is actually on a limited flash storage space of a MCU? Do I get a login, with file storage a graphical X server with KDE or GNOME somehow stripped down and swapped in and out of a multi MB storage device? What kind of I/O would o...

I am new user of AT91SAM7S64, can I use the DEBUG UART to DEBUG programn like JTAG or only use it to download programn to flash through...

I am new user of AT91SAM7S64, can I use the DEBUG UART to DEBUG programn like JTAG or only use it to download programn to flash through SAM-BA?

I've written my own USB bootloader and it is ALMOST working. I'd like to describe my approach and ask for any ideas on what is wrong. First,...

I've written my own USB bootloader and it is ALMOST working. I'd like to describe my approach and ask for any ideas on what is wrong. First, I'm using IAR C-compiler, my own hardware with an AT81SAM7S256 mpu with USB. All bootloader and USB stack code is located at 3B000 (top 16 k of the 256 flash), and will only allow updating of the lower 240k (more than enough for my application). M...

Hello, I am developing a project that may push the limits of SRAM in the larger AVRs family (ATmega1281). After comparing prices and a quick...

Hello, I am developing a project that may push the limits of SRAM in the larger AVRs family (ATmega1281). After comparing prices and a quick browse over datasheets, the AT91SAM7S128 is looking like a better option (SPI over DMA could be useful). I am very familiar in developing with the AVR using WinAVR tool chain, and flash programming with a simple printer port cable. However I have...