Hi all! I have P89LPC932 Rev C, and I can\'t reprograme using ISP again, I using FlashMagic to load hex file from example Hello to micro, but...

Hi all! I have P89LPC932 Rev C, and I can\'t reprograme using ISP again, I using FlashMagic to load hex file from example Hello to micro, but then, micro can\'t enter ISP again, although I send BootLoader . In example, I see that: BSB=1, BOE=1, RPE=1. Can you give any advice? Thanks before! Family ------------------------ Yahoo! Gr

Hi, i would like to test some stepper motors using a P89LPC936. Does anybody have a code that will allow me to do this?? Thank Sarah

Hi, i would like to test some stepper motors using a P89LPC936. Does anybody have a code that will allow me to do this?? Thank Sarah

Hi All, I am considering switching from Atmel AT89Cxx to Philips P89LPC9xx devices and I'm looking for a very easy and low cost way for in...

Hi All, I am considering switching from Atmel AT89Cxx to Philips P89LPC9xx devices and I'm looking for a very easy and low cost way for in circuit programming (ICP, not ISP). What is the cheapest solution for this? I don't want to buy an MCB900 from Keil. With thanks and regards, Mohsen (Australia)

Hi All, SDCC Is free open source (command line) Small Device C Complier which can compile 80c51 code (including Philips LPC900...

Hi All, SDCC Is free open source (command line) Small Device C Complier which can compile 80c51 code (including Philips LPC900 series). Available here http://sdcc.sourceforge.net/ An IDE (integrated development enviroment) Including SDCC is available here. http://www.opcube.com/home.html/ In an attempt not to re-invent the wheel. I am looking for SDCC LPC900 header files for the ...

Hi ! I build a lpc9xx programmer. The ISP mode it's fine, but I can't to program lpc915 with ICP mode. I downloaded the Bridge source code...

Hi ! I build a lpc9xx programmer. The ISP mode it's fine, but I can't to program lpc915 with ICP mode. I downloaded the Bridge source code and recompiled with reg935.h, because I have a LPC936 to Bridge. My circuit don't work to program ICP mode. I programmed lpc936 with the Bridge code, but the VDD and reset control pins don't work. Did anyone use LPC936 as Bridge ISP to ICP ...

Ich werde ab 08.04.2006 nicht im B=FCro sein. Ich kehre zur=FCck am 17.04.2006. Nach meiner Rueckkehr werde ich Ihre Nachricht umgehend...

Ich werde ab 08.04.2006 nicht im B=FCro sein. Ich kehre zur=FCck am 17.04.2006. Nach meiner Rueckkehr werde ich Ihre Nachricht umgehend beantworten. In dringenden Faellen wenden Sie sich bitte an Herrn Rieder ( r...@de.festo.com , +49-711-347-57109 ) Bitte beachten Sie meine neue eMail Adresse: H...@DE.FESTO.COM Please take notice of my new email address: H...@DE.FESTO.COM Festo AG...

Dear ALL, I am using MCB900. When the program that I made was written, it was not possible to write it by ISP twice. I think, my program...

Dear ALL, I am using MCB900. When the program that I made was written, it was not possible to write it by ISP twice. I think, my program erased ISP code. So, I want to recover MCU. What work do you only have to do? and Why did it happen?

Hi friends, I have two types of LPC922. One lot is LPC922F CCxxxx (TSSOP), other in LPC922FN CCxxxx. The verF is supporting multiple...

Hi friends, I have two types of LPC922. One lot is LPC922F CCxxxx (TSSOP), other in LPC922FN CCxxxx. The verF is supporting multiple programming using ISP, while verFN allows to program the chiop onlny once throught ISP. Do you have any idea why its so? Then I tried to implement ICP. I implemented ckt as per AN10258_2, LPC932 in soc

Hello people. I've written an ICP programmer for use with our philips-based products, for use in our mass-production environment. I've based...

Hello people. I've written an ICP programmer for use with our philips-based products, for use in our mass-production environment. I've based it on both the ISP to ICP bridge v1.6 and the ICP Specifications PDF. It manages to erase the chip, write the program data, write the configuration bytes and security bytes, and verifies the CRC (and the CRC matches the original data). The only

Rod, I'am trying to compile the LPC935-PROG on windows using Mingw but the popt.h file wasn't with Mingw. Was that file part of your linux...

Rod, I'am trying to compile the LPC935-PROG on windows using Mingw but the popt.h file wasn't with Mingw. Was that file part of your linux distro? I tried downloading popt.h but I don't think it's the right version since it was missing the define for POPT_TABLEEND. I saw on the internet that it was: #define POPT_TABLEEND {NULL, '\0', 0, 0, 0, NULL, NULL }. I added this but I still get error