EmbeddedRelated.com

Favorite Philips/NXP LPC21xx websites/forums?

Started by John in comp.arch.embedded18 years ago 23 replies

Hi, I've recently started development with a Philips LPC2103. I know Atmel has a site, AT91.com, which I found useful for AT91SAM stuff. ...

Hi, I've recently started development with a Philips LPC2103. I know Atmel has a site, AT91.com, which I found useful for AT91SAM stuff. I'm looking for suggestions or recommendations on websites/forums that discuss using the LPC21xx parts. I did the Google search already but ended up at sites that archive "the real" forums. If it makes a difference, I'm planning on using the ...


SDRAM data garbled due to seperate PCB for SDRAM ???

Started by Mayank Kaushik in comp.arch.embedded19 years ago 19 replies

Hi, Im trying to interface two 128Mbit SDRAMs (MT48LC8M16A2) to the AT91RM9200, but it doesnt seem to be going right. I have a custom...

Hi, Im trying to interface two 128Mbit SDRAMs (MT48LC8M16A2) to the AT91RM9200, but it doesnt seem to be going right. I have a custom board for the AT91, and a seperate board for the SDRAM, the two are connected through an ordinary ribbon cable. The master clock of the uC is running at 60Mhz. To test the integrity of the RAM, im writing data to a series of locations, say from 0x2000_000...


How to write a GDB-STUB for AT91RM9200?

Started by oklm in comp.arch.embedded18 years ago 2 replies

Hello,members! I want to add a debugging stub on AT91RM9200 target,I've looked at some information about it,but i don't know how to write...

Hello,members! I want to add a debugging stub on AT91RM9200 target,I've looked at some information about it,but i don't know how to write that AT91-stub.c? Introduction is: On the host, GDB already understands how to use this protocol; when everything else is set up, you can simply use the `target remote' command . On the target, you must link with your program a few special-purpos...


AT91RM9200/Davicom and Altima phy compability

Started by devlin in comp.arch.embedded18 years ago 1 reply

Hello, We're having two ethernet problems with an Atmel AT91RM9200 CPU based construction. I'm interested if we are the only one having these...

Hello, We're having two ethernet problems with an Atmel AT91RM9200 CPU based construction. I'm interested if we are the only one having these problems... Our first attempt were to use a 16MHz crystal and the AT91 built-in PLL and programable clocks to generate the required 50Mhz and 25Mhz needed for a Davicom DM9161 PHY and a Davicom DM9000 10/100 ethernet controller (thus giving us two e...


AT91RM9200 problems to run from SDRam

Started by Reiner in comp.arch.embedded17 years ago 1 reply

Hi, We build own at91 board with an AT45DB642 and 64MB of SDRam. Above I'll describe some details. At45DB642 is attached to at91rm9200 on...

Hi, We build own at91 board with an AT45DB642 and 64MB of SDRam. Above I'll describe some details. At45DB642 is attached to at91rm9200 on CS0 and SDRam is using a 32bits of data path. We already tested both, and they are working without any kind of problem. We wrote data on At45DB642 and read it without errors, the same occured with SDRAM. What occurs is that when we run a program f...


AT91 - Execution out of internal SRAM

Started by Dan Rhodes in comp.arch.embedded20 years ago 3 replies

Hi All - I'm trying to set up my code to execute out of internal SRAM on an AT91FR40162 using the IAR EWARM toolset. Does anyone have any...

Hi All - I'm trying to set up my code to execute out of internal SRAM on an AT91FR40162 using the IAR EWARM toolset. Does anyone have any advice on how to do this? If the linker thinks ROM starts at 0x00000000 (which it does prior to remap) and the remap command moves the internal SRAM to address 0x00000000, there should be no problem simply copying the code from flash into sram before...


AT91RM9200DK linux newbie - eth0 not there

Started by Rico in comp.arch.embedded17 years ago 1 reply

Hi, I have managed to build my 2.6.21 kernel for my AT92RM9200DK dev board but the ethernet driver is not starting for some reason. I checked...

Hi, I have managed to build my 2.6.21 kernel for my AT92RM9200DK dev board but the ethernet driver is not starting for some reason. I checked the dmesg log and found this: at91_ether: Your bootloader did not configure a MAC address. eth0: Link now 100-FullDuplex eth0: AT91 ethernet at 0xfefbc000 int=24 100-FullDuplex (00:00:00:00:00:00) eth0: Davicom 9161 PHY (Copper) My bootloader ...


Multi-ICE and AT91R40008: Trouble with vector table from Addr 0x00

Started by strut911 in comp.arch.embedded20 years ago 1 reply

Hi everyone. I have a custom board using the AT91R40008. It is actually quite similar to the AT91EB40A board so I am trying to port the Flash...

Hi everyone. I have a custom board using the AT91R40008. It is actually quite similar to the AT91EB40A board so I am trying to port the Flash memory uploader code from the AT91 software library to it. Unfortunately, I am having problems because the flash memory uploader has a file called cstartup_flash.s which is linked to address 0x00. The 0x00 address read only and is used for the flash. B...


whats the diff b\w various arm-xx-gcc versions? (newbie)

Started by Mayank Kaushik in comp.arch.embedded19 years ago 1 reply

Hi, Ive been using ADS till now, but since 45 day trial is gonna end in a few days, i have decided to switch to the GNU toolchain..and...

Hi, Ive been using ADS till now, but since 45 day trial is gonna end in a few days, i have decided to switch to the GNU toolchain..and im painfully new to it. While searching for the particular toolchain to download, i came accross many versions..on gnuarm.com i found arm-elf-gcc etc, on codesourcery.com i found arm-none-eabi-gcc etc, and on the AT91-CDROM i found arm-linux-gcc etc. Exa...


Arm multi-ice with Atmel EB55?

Started by Not Really Me in comp.arch.embedded19 years ago 2 replies

We have an Atmel EB55 board (ARM7TDMI in AT91M55800A chip) and the AT91 expansion memory card. When have debugged projects on it using an...

We have an Atmel EB55 board (ARM7TDMI in AT91M55800A chip) and the AT91 expansion memory card. When have debugged projects on it using an Abatron BDI2000 successfully, but now have to (customer requirement) use a Multi-ice. The multi-ice works fine with the EB55 board, but we can not successfully download code to it if the memory board is plugged in. We have checked the setup again ...


How do you format an ARM axf file to write directly to flash

Started by Chris in comp.arch.embedded20 years ago 1 reply

Hi everyone. I have a program running on my AT91 board (using AT91R40008) that can send data to flash via xmodem. I also have an ARM AXF file...

Hi everyone. I have a program running on my AT91 board (using AT91R40008) that can send data to flash via xmodem. I also have an ARM AXF file that I want to burn into the flash. How do I format the AXF file to burn it into flash? Do I burn it directly or does any formatting need to take place. Chris


Recent U-Boot for Atmel SAM9 boards?

Started by Grant Edwards in comp.arch.embedded14 years ago 1 reply

I'm working with the Atmel's patched U-Boot 1.3.4 for a SAM9G20 board (from http://www.at91.com/linux4sam/bin/view/Linux4SAM/U-Boot). I'd much...

I'm working with the Atmel's patched U-Boot 1.3.4 for a SAM9G20 board (from http://www.at91.com/linux4sam/bin/view/Linux4SAM/U-Boot). I'd much rather be working with a more recent version (understandably, the U-Boot developers aren't very keen on support a version that's more than 2 years old). Does anybody have a more recent version of U-Boot working on an Atmel SAM9 board (e.g. ATSAM9G20...