Hello, Anybody had a chance to implement PCI bus on pxa255-based machine? Is there any ready made bridge chip (say, from Intel, or not) so...

Hello, Anybody had a chance to implement PCI bus on pxa255-based machine? Is there any ready made bridge chip (say, from Intel, or not) so that I won't need to deal with FPGA programming...? TIA Sergei

Wondering if anyone has used any of these parts: http://www.ftdichip.com/FTProducts.htm If yes, how did it go? Any significant problems with...

Wondering if anyone has used any of these parts: http://www.ftdichip.com/FTProducts.htm If yes, how did it go? Any significant problems with operation, availability, support, ...? We're looking to use the FT2232C in the MCU Host Bus Emulation mode to communicate with an FPGA in a different chassis. Thanks, Rob

Hi, i know that this question might have been posted umpteen times here but here's me reiterating it... I am a newbie who wants to embark in to...

Hi, i know that this question might have been posted umpteen times here but here's me reiterating it... I am a newbie who wants to embark in to the (for now) dark world of FPGAs. I dont have access to hardware for now. I have considerable experience with PIC, AVRs. Any directions? --------------------------------------- Posted through http://www.EmbeddedRelated.com

Hello I want to connect a FPGA with uC to send some data (144 Mbits). My question is: Is there any parallel bus specification which I can...

Hello I want to connect a FPGA with uC to send some data (144 Mbits). My question is: Is there any parallel bus specification which I can use? Have you any recommendation? -- PGW posted to sci.electronics.design, comp.arch.embedded

I found an ancient piece of hardware. An old notebook with a 10" 800x600 LCD. Is it hard to drive a notebook LCD with some SBC or FPGA? Are...

I found an ancient piece of hardware. An old notebook with a 10" 800x600 LCD. Is it hard to drive a notebook LCD with some SBC or FPGA? Are there standards for this? Atilla

I want to control a system including DSP+FPGA+FLASH+ADC+sensor by USB port, program all chips by USB . what kind of bus shall i use? is there...

I want to control a system including DSP+FPGA+FLASH+ADC+sensor by USB port, program all chips by USB . what kind of bus shall i use? is there any reference design projects online? thanks!

Hi, I have to start working on two boards TS-7200 and an fpga I was wondering what kind on oscilloscope should I get? With TS-7200,...

Hi, I have to start working on two boards TS-7200 and an fpga I was wondering what kind on oscilloscope should I get? With TS-7200, I am going to be using pc like protocols(rs323--i2c), over general purpose pins. Thank you. --------------------------------------- Posted through http://www.EmbeddedRelated.com

I am developing an FPGA application which works in series with a main processor which is running an RTOS(VxWorks). Since my inputs and outputs...

I am developing an FPGA application which works in series with a main processor which is running an RTOS(VxWorks). Since my inputs and outputs are to and from that processor, should i be using any RTOS? Kindly clarify. thanks in advance. Regards Surya.

Hi. I'm an Undergrad student & we're designing an 8051 core. Could you plz tell me if it is likely to fit on 'Altera Cyclone...

Hi. I'm an Undergrad student & we're designing an 8051 core. Could you plz tell me if it is likely to fit on 'Altera Cyclone EP1C12Q240C8' ? Will Quartus II web edition(version 5.1) be sufficient for all the design flow steps(including programming) ? Or do we need a purchased version? Thanx in Advance. Neha .

Hi everyone, we have a modified microblaze (mblite) on top of which we added an fpu and everything is implemented in an FPGA. I'm now facing...

Hi everyone, we have a modified microblaze (mblite) on top of which we added an fpu and everything is implemented in an FPGA. I'm now facing the issue to generate a toolchain for this platform [1] and I have some doubts on how to proceed. First I'd like to say that I haven't found a single one release from Xilinx that I can potentially rely on. Several Xilinx webpages point to a ve...

Hi, We currently do most (all) our embedeed FW testing on either real HW (if available), using FPGA, or using HW simulator and Verilog...

Hi, We currently do most (all) our embedeed FW testing on either real HW (if available), using FPGA, or using HW simulator and Verilog models. We are looking at performing more testing on the "Host" rather than the target, and since this is new to our group, I am looking for suggestions and comments. BTW, we use C, currently we don't use an RTOS, but going forward, this is something that we wil...

Hello all, I've had an enquiry in about a project that is mostly simple enough, I'll be using an FPGA for what's required, the fly in the...

Hello all, I've had an enquiry in about a project that is mostly simple enough, I'll be using an FPGA for what's required, the fly in the ointment is the client wants the thing unit via TCP/IP. All the ethernet interface is going to be used for is driving and reading internal registers, it could very easily be done via RS-422 (which is an option) but it looks like they definitely want TC...

We have been encouraged to spend some of our remaining training budget by taking a week-long seminar in September. I am looking for...

We have been encouraged to spend some of our remaining training budget by taking a week-long seminar in September. I am looking for something concerning FPGA design, wireless networks, or just general engineering. My preference would be somewhere in southern California, but other places may be negotiable. Any suggestions?

Hi, For a quite large project dealing with Virtex 4, DDR2, gigabit ethernet and digital signal processing, I'm looking for a top of the bill...

Hi, For a quite large project dealing with Virtex 4, DDR2, gigabit ethernet and digital signal processing, I'm looking for a top of the bill design house in a far east country like india. All tips are welcome. Best Regards, Anom

Does anyone know of any software, ideally freeware, which can use the above JTAG interfaces to exercise other JTAG interfaces on non FPGA...

Does anyone know of any software, ideally freeware, which can use the above JTAG interfaces to exercise other JTAG interfaces on non FPGA devices? In my case I'd like to read the state of pins on an unrelated device.

Hi everybody!! I'm a spanish strudent on Systems Engineerering, and I'm very interested on microcontrollers and its applications. In my degree...

Hi everybody!! I'm a spanish strudent on Systems Engineerering, and I'm very interested on microcontrollers and its applications. In my degree I've been working with two types of them, a Spartan FPGA and a Motorola MC68HC11 microcontroller. I also know that is usual to use PICs as small microcontrollers. But a question is rounding on my mind, because I don't undestand completely which are...

hey! i am using spartan 3E board to transmit UDP packets to my pc. I have implemented most of it, i have interfaced the PHY but there seems to be...

hey! i am using spartan 3E board to transmit UDP packets to my pc. I have implemented most of it, i have interfaced the PHY but there seems to be one problem, the data leaves the FPGA bt the packet is dropped at the pc's end, how i know it is that i can see the light blink bt nothing gets through to ethereal. I am assuming that my crc32 is not correct as i have double checked my other headers, t...

Hi, I'm starting on FPGAs. How about Xilinx Spartan 3 starter kit?. It's any better under...

Hi, I'm starting on FPGAs. How about Xilinx Spartan 3 starter kit?. It's any better under $200. http://www.xilinx.com/products/spartan3/s3boards.htm Best regards, Rodrigo.

Hi there, I just need to known if there is possible to use a USB device (flash drive, webcam, keyboard, etc.) with no computer interaction, so...

Hi there, I just need to known if there is possible to use a USB device (flash drive, webcam, keyboard, etc.) with no computer interaction, so I can use it in a specific application with a FPGA ???? Thanks in advance.

Hi All, I'm working on a custom device and need to monitor serial data between a CPU and an FPGA at 921KBps. Can anyone recommend a PC...

Hi All, I'm working on a custom device and need to monitor serial data between a CPU and an FPGA at 921KBps. Can anyone recommend a PC program that could do this? I need to monitor both the TX and RX lines at the same time. Thanks, Sean