Forums Search for: RS232
Help needed in FT232RL CBUS bit bang mode
Hi, I have made a custom RS232 to USB converter using FT232RL IC and its working fine... I have read the Mprog utility and programmed my...
Hi, I have made a custom RS232 to USB converter using FT232RL IC and its working fine... I have read the Mprog utility and programmed my IC's CBUS 2 to I/O mode... Now i need to use FT_SetBitMode() to make it high or low... can anyone please help me in doing it... I use VC++ 6.0 and i have read the data sheets and he application notes for bitbang mode and even the programmers guide......
Browser Terminal
inI'm seeking a terminal that has a browser built in. Here are the requirements 1. Low power - like seriously low (most terminals I've seen are...
I'm seeking a terminal that has a browser built in. Here are the requirements 1. Low power - like seriously low (most terminals I've seen are far too power hungry) 2. Small LCD, need only be monochrome, backlight is optional. 5.7" diagonal is absolute max. Probably prefer smaller. 3. Touch screen. 4. Prefer options for RS232, Ethernet or USB interface. I would like to use it as a pane...
Could PIC handle this?
inCould a PIC handle interfacing via rs232 with a GPS unit, and comparing the location against a list of ~5000 stored positions, and alerting...
Could a PIC handle interfacing via rs232 with a GPS unit, and comparing the location against a list of ~5000 stored positions, and alerting (LED/LCD) if any points are considered close enough (~1-2km, using haversine formula, perhaps)? I guess the points would have to be stored on a CF/MMC card. They would be updated/changed time to time...
low cost ARM development/learning board
inHello; I own a PICDEM2+ (LCD display, temperature sensor, buttong, potentiometers, SMBUS interface (serial bus interface...
Hello; I own a PICDEM2+ (LCD display, temperature sensor, buttong, potentiometers, SMBUS interface (serial bus interface instead of a regular [parallel] bus), RS232 & JTAG interfaces, connections for battery or "wall wart" power and an electronics prototyping area). The IDE software is pretty good for the price (low_cost/free), but I'm looking now at w...
Recommend an RS232 Monitor?
inHi all, I'm getting up to speed on the MSP430 with the ez340-Rf2500 dev kit, which connects to a pc via a USB-to-serial emulator. That is, the...
Hi all, I'm getting up to speed on the MSP430 with the ez340-Rf2500 dev kit, which connects to a pc via a USB-to-serial emulator. That is, the device is plugged into a USB port, but shows up as a COM port in Windows. For my application, I'd like this device to report real-time sensor data to the host computer, where it will be logged. I figure I should really have a serial port sniffer to ai...
how do you read the contents of the CTS signal on VB6?
inwhats the simplest way(VB6 code) to read the contents or status of rs232 input signal CTS?
whats the simplest way(VB6 code) to read the contents or status of rs232 input signal CTS?
avr butterfly and jtag
inI have bought an AVR Butterfly as my first step in exploring the wonderful world of microcontrollers, and have worked out how to compile and...
I have bought an AVR Butterfly as my first step in exploring the wonderful world of microcontrollers, and have worked out how to compile and load programs into it using WinAVR, AVR Studio and the RS232 connection. And all for ? 30! Now I want to try my hand at on board debugging. Do I just buy the JTAG dongle for ? 45 and talk through it to the Butterfly with AVR Studio? I can hardly bel...
Anyone ever use a Jeteye IR with a PIC?
inA surplus store in our city is selling the "Jeteye PC" device for $1. It appears to be a rs232 IR sender/receiver in a cute small package. I...
A surplus store in our city is selling the "Jeteye PC" device for $1. It appears to be a rs232 IR sender/receiver in a cute small package. I cracked it open and found 3 SMD chips, a crystal and a 2 bulb IR device (plus a few caps and transistors). I looked up the chips with an online data sheet service. One of the chips is a 8 pin low dropout regulator. The other 2 have me stumped: ...
Embedded Linux for automotive
inI'm searching for an embedded hardware that should run Linux OS on a vehicle. I don't need special features: - VDC in - RS232 port (not USB...
I'm searching for an embedded hardware that should run Linux OS on a vehicle. I don't need special features: - VDC in - RS232 port (not USB adapter) - Ethernet - SSD or soldered Flash (just to avoid magnetic HDD) - analog audio input and output I prefer a board with ready connectors, such as a PC desktop motherboard. I don't want to develop and produce a baseboard. It should be ni...
mp3 network player
inHello! I'm looking for a way to build small mp3 network player. It should be something like http://mp3elf.net/ but cheaper. Could you suggest...
Hello! I'm looking for a way to build small mp3 network player. It should be something like http://mp3elf.net/ but cheaper. Could you suggest me some embedded system that has: - low price - stereo output - ethernet with tcp/ip - rs232 (not necessarily) - lpt (for LCD) Of course, it should be fast enough to decode 320 kb/s mp3 files. System could be stored locally on flash or booted o...
OV7620 RGB demosaicing problem
inHello, I'm working on an imaging system which uses C3188A digital cmos camera(contains OV7620 image sensor). It is controlled by a PIC18F452...
Hello, I'm working on an imaging system which uses C3188A digital cmos camera(contains OV7620 image sensor). It is controlled by a PIC18F452 and each frame I want to view is stored in a FIFO buffer, AL422B. I can store a frame and transfer it to my PC by RS232. However I have a problem with the images, they look gray scale although they should be RGB. I have configured OV7620 to transmit QVGA...
USB-CDC Driver compatibility
Hi all, I want to build embedded system with USB-based communication device to transfer data and update the configuration. I've googled and...
Hi all, I want to build embedded system with USB-based communication device to transfer data and update the configuration. I've googled and found that the USB CDC class is not "standarized" (why do we need standards if there's so many of them??)..The USB CDC is divided into : 1) CDC - ACM : For old serial modems (including RS232-USB bridge/converter) 2) CDC - Ethernet : The "real" ethe...
MCU + USB
inHi, I don't know if there is a better group to ask about USB. I want to create a device that will communicate with a PC via USB. I prefer...
Hi, I don't know if there is a better group to ask about USB. I want to create a device that will communicate with a PC via USB. I prefer USB to RS232 because I plan to power the device from the USB supply. I guess I have (at least) two options: 1) I use an MCU with integrated USB interface. 2) I use any MCU, plus an FTDI FT232R (USB-UART device), or equivalent. Option 2 makes pro...
I need HDLC transceiver for interfacing with Serial Communication Controller
inHello Sir, I have to interface Serial communication controller- SCC(PEB20534) with HDLC transceiver through synchrocous...
Hello Sir, I have to interface Serial communication controller- SCC(PEB20534) with HDLC transceiver through synchrocous signals(TXCLK,RXCLK,TXDATA,RXDATA). Can you tell me the HDLC transceiver with RS232/RS422? Regards, N.Magalingam
Multiple USB port controller chip
inHi, I wanted to know if there is any controller chip for controlling upto 4 USB ports,It will be great if any one of you can give information...
Hi, I wanted to know if there is any controller chip for controlling upto 4 USB ports,It will be great if any one of you can give information about controller chips for multiple USB and RS232/422/485 ports.I have come across LSI's L1501.
ADUC842 does not respond to serial check
inHi to all the ng Can you help me please? I mounted at home a board using an ADUC842.I comunicate with PC by means of a simple RS232 to TTL...
Hi to all the ng Can you help me please? I mounted at home a board using an ADUC842.I comunicate with PC by means of a simple RS232 to TTL converter as shown in http://157.158.56.13/Electronics_Firm_Docs/ANALOG/uC006.pdf The 32768 KHz Xtal oscillates,i have connected digital and analogs VDD's.EA is tied to High logic level When i exit from RESET state presenting PSEN Low the ADUC send...
Anyone used Portmon on a USB-RS232?
inOk, folks, Portmon shows COM6 which is the port to a scope, via a USB connection. The terminal program (TeraTerm) is talking to it via that...
Ok, folks, Portmon shows COM6 which is the port to a scope, via a USB connection. The terminal program (TeraTerm) is talking to it via that port. Later it's going to be a VBA routine and that's why I need to monitor, to see what gets stuck or doesn't appear. Long story short I can set Portmon to monitor all other COM ports but not COM6. Says "Portmon cannot attach .... device may be in ...
sdcc, 8051/8031 in C
inI've bought some time ago 8051 learning kit with monitor in ROM and 8k external ram starting at 0x8000h, where programs in intel hex format...
I've bought some time ago 8051 learning kit with monitor in ROM and 8k external ram starting at 0x8000h, where programs in intel hex format are load to external RAM via RS232 if i want to start this program i have to press 0 and type address 8000 (where the program is), then the program is running Now i have a problem, i trying many things to make it come working like i want, but i didn't ma...
USB chip
inHello, Who can help me with some information about the existing USB chips... There are a lot of suppliers and kind of USB chips for HID,...
Hello, Who can help me with some information about the existing USB chips... There are a lot of suppliers and kind of USB chips for HID, Audio, Video. The project I am on now is creating a serial data logger. I use a spy microcontroller board witch catches the RS232 data between 2 devices. The board then has to send the data it receives through USB to the computer (delphi software). I want...
pic16f877a uart c code problm
inHai to all, Iam trying to communicate from pic 16f877a to the pc's hyperterminal at 9600 baud rate. Iam posting my code for this. Iam able...
Hai to all, Iam trying to communicate from pic 16f877a to the pc's hyperterminal at 9600 baud rate. Iam posting my code for this. Iam able to simulate with mplab but I could not implement with hardware. I checked for max232, rs232. They seem to be working perfect. But iam not getting the data through hyperterminal comm port. My crystal oscillator is 8mhz. /* uart serial communicati...