Forums Search for: Schematic
Coldfire and SDRAM
inHi, According to the MCF5272 datasheet, and the schematic, the address line A22 and A23 of ColdFire are to be treated as SDBA0 and SDBA1...
Hi, According to the MCF5272 datasheet, and the schematic, the address line A22 and A23 of ColdFire are to be treated as SDBA0 and SDBA1 and connected to BA0 and BA1 of the SDRAM respectively. But when the register value is set according to the above, the SDRAM initialisation faces problem. But when i set a value in such a way that the address lines A23 and A24 of ColdFire are connecte...
BSD licenced microprocessor indi (MAX II 386 LEs)
inhi BSD licence microprocessor 283 LEs 6% Cyclone II EP2C5T144C6 44 Warnings Still unverified. just retargeted to MAX II to see how it...
hi BSD licence microprocessor 283 LEs 6% Cyclone II EP2C5T144C6 44 Warnings Still unverified. just retargeted to MAX II to see how it went. looks good. 386LEs 17% MAX II EPM2210F256C3 yes got it to compile at last after discovering a bit more about buses and naming of them. TEST16 toplevel object schematic encapsulates the indi16 with reset logic and tristate databus, to co...
uPDxxxxx chips datasheets (camcorder, vcr, etc)
inDoes anyone have a repository of datasheets or at least valid signal descriptions for uPD series chips used in Matsushita...
Does anyone have a repository of datasheets or at least valid signal descriptions for uPD series chips used in Matsushita (Panasonic) camcorders, vcrs, etc.? Currently I am seeking data on the uPD9313G or uPD9313GB video sync generator; the pin descriptions for this part, on a schematic in a camcorder service manual, are incorrect, as evidenced by a block diagram which labels the pins enti...
Help::::::::::Schematic of 28c64 interfacing with 8051
Hi, I have tried interfacing 28c64 with 8051 using 74ls573.. exact eeprom ic no. is D28c64c-25. First I wrote a simple program to write...
Hi, I have tried interfacing 28c64 with 8051 using 74ls573.. exact eeprom ic no. is D28c64c-25. First I wrote a simple program to write single byte in first location of eeprom by tying WR of 8051and WE of 28c64..I kept OE high.. And LE of 74ls573 to ground.. I have connected higher address A8 to A12 from port P2 directly to 28c64.. When I was tryi...
(Revised) Simple PCB circuit-tracing technique (1 or 2 sided)
in(reposted due to error in URL embedded in previous post -- can't cancel through our nntp host) Hello all, Although this is certainly...
(reposted due to error in URL embedded in previous post -- can't cancel through our nntp host) Hello all, Although this is certainly elementary, I thought I'd share it since it may help someone in a pinch; here is my simple technique to create a preliminary schematic from a populated 1 or 2 sided pcb: http://ipx1.cybertheque.org/homebrew/pcb-photog/ Regards, Michael Grigoni Cy...
build an arm board to run linux
inI want to build an arm board to run linux. I'm not really interested in buying a board and messing around with it. I would go for a...
I want to build an arm board to run linux. I'm not really interested in buying a board and messing around with it. I would go for a schematic though. Any pointers on how I could get started? I have heard mixed advice from people. Some say the atmel arm microcontrollers are pretty easy to hook up to other components, some say it's not that simple. I just want to know how I can get started.
Recomendations for document control software
inHi, I think this has been discussed here before, but a search on google groups did not provide much info. I am looking for software to help...
Hi, I think this has been discussed here before, but a search on google groups did not provide much info. I am looking for software to help with document control. I typically have the following documents for a project. 1. Schematic Source files as well as PDF versions. 2. PCB Source files as well as PDF and Gerber versions 3. Datasheets on all the ICs used. User manuals etc. on more comp...
Timing analysis of *asynchronous* bus peripherals
inHello everyone, I have a (maybe) simple problem I don't know exactly how to face up. I am given a digital schematic design (which is made by a...
Hello everyone, I have a (maybe) simple problem I don't know exactly how to face up. I am given a digital schematic design (which is made by a third person) that realizes simple bus peripherals inside a Altera MAX CPLD. The design is quite simple: the address bus along with the data bus and the READ signals are brought as inputs of the CPLD (outputs are not considered here). There is a combi...
deciding capacitor & resistor values
inI am new to schematic design and studying OLinuXino A10s schematics. A generic question : How do we decide the resistor & capacitor values...
I am new to schematic design and studying OLinuXino A10s schematics. A generic question : How do we decide the resistor & capacitor values required to interface multiple ICs on a pcb ? E.x. I am unable to understand why a 22ohm resistor is present in the clock signal (SCK,SCK# pins - W2, Y1 ) from A10s to SDRAM (h5tq2g83cfr-h9c) (CK, CK# pins - F7, G7). It is not given in either of their da...
Averlogic AL250 and scan doubling
inDoes anyone have experience with the Averlogic AL250 Video Scan Doubler IC? Datasheet is...
Does anyone have experience with the Averlogic AL250 Video Scan Doubler IC? Datasheet is here http://www.ortodoxism.ro/datasheets/Averlogic/mXvqxzx.pdf and Application notes http://www.ieechina.com/Upload/Tech/200405191539390937.pdf As far as interfacing to this IC, do think it's out of reach for a beginner? They don't provide a schematic for their evaluation board, but the par...
Atmel ARM AT91SAM7S256 USB Question
inHi, On our project, we are considering an ARM with a USB interface (Atmel AT91SAM7S256). From looking at the datasheet, it appears that we...
Hi, On our project, we are considering an ARM with a USB interface (Atmel AT91SAM7S256). From looking at the datasheet, it appears that we need an 18.432 MHz crystal for the USB to operate at full speed. Is this correct? The datasheet seems to be a bit ambiguous in this regard. I looked at the schematic for Atmel's AT91SAM7S-EK evaluation board and noticed that they are using an 18.432 ...
ANN: new Pulsonix version 3 PCB software released
inI've been helping to beta test version 3 of Pulsonix for the last few months. It has now been released and is available for download...
I've been helping to beta test version 3 of Pulsonix for the last few months. It has now been released and is available for download from: http://www.pulsonix.com. Without a license it's a full working demo (up to 100 pins for schematic entry and PCB design) and Pulsonix will provide a 30 day license for a fuller evaluation on request. Pulsonix support is excellent and bugs get fixed v...
Transferring data via USB on ML-310
inI want to use the USB port of the ML-310 to transfer data out to the computer. Is this possible ? How can I access the Ali South Bridge from...
I want to use the USB port of the ML-310 to transfer data out to the computer. Is this possible ? How can I access the Ali South Bridge from the FPGA (i.e. in my top Schematic program) ? How does the computer itself communicate with the board. Would the computer require a specific driver? Is there any DLL for Ali South Bridge ? Thanks This message was sent using the comp.arch...
Need schematic to make programmer for PIC18 series
inI want to build my own hardware programmer to program the Microchip PIC18 series of devices. I want to use the parallel port or possibly the USB...
I want to build my own hardware programmer to program the Microchip PIC18 series of devices. I want to use the parallel port or possibly the USB port. I don't want to use the serial port because they are now obsolete and no longer ship on newer computers. USB-to-Serial adapters cannot be used because programmers like IC-Prog and WinPic cannot work with these "virtual" serial ports - they need...
56800/E dsp jtag adapter?
inHi, in the CodeWarrior v7.2 for the Freescale hybrid 56800/E DSP series it is stated the IDE can program e.g. 56F8322 using the Motorola JTAG...
Hi, in the CodeWarrior v7.2 for the Freescale hybrid 56800/E DSP series it is stated the IDE can program e.g. 56F8322 using the Motorola JTAG Parallel Port Converter (which, as this is a hobby project, I'm not very inclined to buy for > $200 and wait 4+ weeks for). One (inofficial?) schematic for the Motorola JTAG Parallel Port Converter is apparently at http://www.hc08.cz/attachment
Pic and ICSP
inI shoud program a PIC16f877A with a jdm based programmer (PIC-PG2: http://www.olimex.com/dev/pic-pg2c.html) and IC-prog. I found a schematic...
I shoud program a PIC16f877A with a jdm based programmer (PIC-PG2: http://www.olimex.com/dev/pic-pg2c.html) and IC-prog. I found a schematic for ICSP connection with a jdm-programmer (http://www.jdm.homepage.dk/icsp.htm) but i used instead 1n4448 diode a 1n4148. It doesn't works. Someone can help me? Thanks -- I have a little dreidel, I made it out of clay And when it's dry and ready,...
schematic of a motor controller circuit using pic18f4331
inCan someone help me out with the scematic of the motor controller with PIC18f4331, l298 and a quadrature encoder. I already implemented the...
Can someone help me out with the scematic of the motor controller with PIC18f4331, l298 and a quadrature encoder. I already implemented the motor controller with a pic 16f877a, but later I had to abandon that idea as 16f doesnt support quadrature encoder modules.. I adjusted the 16f circuit diagram for 18f4331 , but It doesn work.. 18f4331 has additional PWM pins. what r they used for? I read the ...
Extract program from old mask-ROM 80C51?
inI have a mask ROM 80C51 in an old computer, made 1992. The top of the 44 pin PLCC says: Philips logo 0290,031-01 WP J399 223380 DfD9240V6...
I have a mask ROM 80C51 in an old computer, made 1992. The top of the 44 pin PLCC says: Philips logo 0290,031-01 WP J399 223380 DfD9240V6 YU (R) (C) INTEL 1980 (R) PHILIPS 1989 The schematic tells me it's an 80C51, but no other part numbers. 0290,031-01 is the customer's (Acorn's) part number. I don't know what sort of 8051 it is inside. The clock line XTAL1 is driven directly fr...
Cyclone 3 Starter Board Question
inAnyone know how the USB Blaster cable loads data to the C3 fpga on the board? The schematic shows a CPLD between the FPGA and the USB...
Anyone know how the USB Blaster cable loads data to the C3 fpga on the board? The schematic shows a CPLD between the FPGA and the USB port. There is a USB to parallel chip between the cpld and the usb port. But I do not see any serial or parallel data going to the fpga. I wish Altera added more details to the starter kit documentation. There is all this source code but it is encrypted. So...
Yahoo group for FreePCB, open source PCB layout
inI could not find much info on users of FreePCB, so I started a Yahoo group. FreePCB is an open source program for PCB layout. It works with a...
I could not find much info on users of FreePCB, so I started a Yahoo group. FreePCB is an open source program for PCB layout. It works with a PADSPCB netlist from any schematic package. http://groups.yahoo.com/group/FreePCB/ Come check it out and let us know if you are a user. http://www.freepcb.com/