Hello, Does somebody know a new type of processor that is capable to run (unmodified) 6800 code? (Like for the 68HC11). ...

Hello, Does somebody know a new type of processor that is capable to run (unmodified) 6800 code? (Like for the 68HC11). Thanks, Kind regards, Edzard Kolks Eindhoven - Holland

Over the past 20 years, I have completed a large number of 68HC811E2 based designs using the Optrex DMC series LCD displays. ...

Over the past 20 years, I have completed a large number of 68HC811E2 based designs using the Optrex DMC series LCD displays. Previous design requirements have dictated a clock speed above 1MHz. Because of the timing limitations of the DMC series displays, I have used latches a

does any one know how to convert a .bmp file to either hex or .s19 to be used with a graphics display.im wanting to convert .bmp...

does any one know how to convert a .bmp file to either hex or .s19 to be used with a graphics display.im wanting to convert .bmp files to make it easier to create the graphics i want to display on the lcd screen.

Man has this group been QUIET! WAKE UP! Motorola is discontinuing the HC11 family! JUST KIDDING! I upgraded my AEVM when I...

Man has this group been QUIET! WAKE UP! Motorola is discontinuing the HC11 family! JUST KIDDING! I upgraded my AEVM when I switch to an XP based PC. P&E kindly gave me their XP-compatable Win IDE, version 1.2 but I haven't used it much. I have a new MC6

I have a legacy hc11 application in an 68hc711e9 with OTP ROM which has at one point an instruction that is (raw instruction...

I have a legacy hc11 application in an 68hc711e9 with OTP ROM which has at one point an instruction that is (raw instruction bytes $20FE) loc BRA loc ie an infinite loop. What bytes can I reprogram these two bits to function as to avoid this loop? NOP is

Hi, I'm wondering if it is possible to check if a 68hc711 has the security feature enabled (by putting it into a development...

Hi, I'm wondering if it is possible to check if a 68hc711 has the security feature enabled (by putting it into a development board) without clearing the content of the EEPROM? http://groups.yahoo.com/group/m68HC11/m es

Hello, I am trying to attach a 74HC589 8-bit parallel in/serial out shift register to my SPI port. I have a 68HC11E0 running in...

Hello, I am trying to attach a 74HC589 8-bit parallel in/serial out shift register to my SPI port. I have a 68HC11E0 running in expanded mode with 32K RAM and 32K EEPROM. It is a unit called the Microcore-11 from Technological Arts. I have read the newer White book on the SPI port

OK, so i'm working on this project using the HC11 in expanded mode. I need to figure out two specific things. I need to use Port B...

OK, so i'm working on this project using the HC11 in expanded mode. I need to figure out two specific things. I need to use Port B for output, and Port C for inputs. For Port B, I want to be able to say PORTB=0xA3, and have the pins on PortB be 1010 0011, as checked with a

--- In , "Bob Smith" wrote: > Sorry about the typo -- > > > See the 74HC165 for input ports and the 74HC794. > > should...

--- In , "Bob Smith" wrote: > Sorry about the typo -- > > > See the 74HC165 for input ports and the 74HC794. > > should read - > > > See the 74HC165 for input ports and the 74HC794 for output ports.

Group; What commercial productin programmers are available for the HC711E9? TIA Dennis ...

Group; What commercial productin programmers are available for the HC711E9? TIA Dennis