Disabling ETM with a wriggler

Started by nonuckingfumber in LPC200011 years ago 2 replies

Using a wriggler with a 2106 it seems that the ETM pins also get activated when starting in DEBUG. Is there any way to disable this, the...

Using a wriggler with a 2106 it seems that the ETM pins also get activated when starting in DEBUG. Is there any way to disable this, the wriggler does not even connect to them but as far as I can see there is no way to do it with PINSEL on this chip. Is it possible via JTAG?


Re Reflashing in circuit

Started by Owen Mooney in LPC200014 years ago

Some time ago I posted a message asking for the suggestions to reflash a 2106 to update the firmware in an existing product I...

Some time ago I posted a message asking for the suggestions to reflash a 2106 to update the firmware in an existing product I followed one suggestion which works very well. This accepts a certain character sequence then uses the IAP programming to destroy the first pa


I O Port driving capacity

Started by rohan patil in LPC200013 years ago 3 replies

i m final year student of electronics engg i m trying to interface 16x2 lcd display with lpc 2106 io ports are connected as...

i m final year student of electronics engg i m trying to interface 16x2 lcd display with lpc 2106 io ports are connected as follows D0-P0.21.........D7-P0.28 lcd enable-p0.29 RS-p0.30 R/W is grounded i have sucessfully implimented clear disply command but i m not able to write data is it the problem of


LPC2214 boards

Started by Curt Powell in LPC200014 years ago 5 replies

Does anyone have any recommendations for 2214 header boards? We're looking for fully assembled and tested with at least 1M RAM....

Does anyone have any recommendations for 2214 header boards? We're looking for fully assembled and tested with at least 1M RAM. (We've had good luck with Olimex's 2106 but according to their web site their 2214s aren't available yet.) TIA, Curt


Rowley library tutorial / cross polination?

Started by matterama3444 in LPC20009 years ago

Hi all, (Paul, I hope you're reading this :) ) I have been using CrossStudio for a little over a year, and love it. For my stuff, it has...

Hi all, (Paul, I hope you're reading this :) ) I have been using CrossStudio for a little over a year, and love it. For my stuff, it has worked great (2106, 2136, 2138 and 2368 variants so far), so much so that when something doesn't work I know to double / triple / quadruple check myself first to save an embarrassing help request. Anyway... I'm at the point where I have a speci...


How interface lpc2106 with w3100A(Wiznets)

Started by lokanadham p in LPC200013 years ago

Hi, I am doing my M.Tech project on designing of VOIP phone, any body please help me how to interface the LPC 2106 with the Wiznet's W3100A...

Hi, I am doing my M.Tech project on designing of VOIP phone, any body please help me how to interface the LPC 2106 with the Wiznet's W3100A . W3100A is a hardwired tcp/ip chip. regards lokanadham --------------------------------- Enjoy this Diwali with Y! India Click here


Code protection again....

Started by ggindele in LPC200013 years ago 5 replies

I think we reached the consensus (with a little Philips help) that code protection is available only in the 64 pin package, when...

I think we reached the consensus (with a little Philips help) that code protection is available only in the 64 pin package, when the boot loader >= 1.63 I wonder would that be a commercially reasonable protection when 2106 is used with an external electronic serial n


Weird I2C behaviour

Started by Shannon Holland in LPC200014 years ago 1 reply

I'm trying to get I2c up and running on my 2106 board and am seeing strange things. Basically, when the LPC2106 brings SCL low I...

I'm trying to get I2c up and running on my 2106 board and am seeing strange things. Basically, when the LPC2106 brings SCL low I see the line dropping only to 1.5V rather than 0. I can verify this by switching P0.2 to GPIO mode and outputting 0. SDA fluctuates between 0 and


OS X Flash Programming of LPC-2106?

Started by Brian Short in LPC200014 years ago 1 reply

I am new to this, so please be patient. I have downloaded the GCC files, but I am trying to see ho to download files to the...

I am new to this, so please be patient. I have downloaded the GCC files, but I am trying to see ho to download files to the hardware (Tini-ARM). Is there a Flash Programming Utility for Mac OS X? Brian


usb printer with lpc2106

Started by jha_santosh_kr2005 in LPC200013 years ago 5 replies

Hi I want to attach usb inkjet printer(any model)with lpc 2106 to get the text as well as picture print out. can any body...

Hi I want to attach usb inkjet printer(any model)with lpc 2106 to get the text as well as picture print out. can any body guide me? Santosh jha


A general greeting and non-specific introduction to all.

Started by Greg in LPC200014 years ago

As the subject title suggests, I'm new to this group, although a long time lurker. I have been intimate with AVRs for a while...

As the subject title suggests, I'm new to this group, although a long time lurker. I have been intimate with AVRs for a while now and recently moved to the LPC 210x in the form of the 'tinyarm' DIP40 (2106) and IAR IDE. I've been at it now for a week and have finally come to


Any experience of the LPC2130 under very low power?

Started by Owen Mooney in LPC200013 years ago 9 replies

I am looking at a new design for a very low power logger. I like the LPC 2106 very much - but its not quite right, so I was going...

I am looking at a new design for a very low power logger. I like the LPC 2106 very much - but its not quite right, so I was going to use a PIC (nasty after the luxury of a decent processor). I need: Sub 50 microamps normal operation (idle or power down) Ability


first project temperature control

Started by Danny Dom in LPC200011 years ago 2 replies

I want to start with ARM but I don't know if I made the correct choise to work with ARM I have bought 2 simple boards one with a 2106 and...

I want to start with ARM but I don't know if I made the correct choise to work with ARM I have bought 2 simple boards one with a 2106 and another with a 2138 just the jtag interface and the processor board. I want to read the temperature in my house on 7 different locations, and so opening the valves on the radiators. For the temperature I would like to use the DS1820, if it is possible to...


2106 and 2138 interrupt and IOPIN

Started by charlesgrenz in LPC200012 years ago 2 replies

Hello group, Have a strange problem. The following code works perfectly on a LPC2106. if (((T1IR & T1IR_MR2INT) != 0) || (T1MR2 <...

Hello group, Have a strange problem. The following code works perfectly on a LPC2106. if (((T1IR & T1IR_MR2INT) != 0) || (T1MR2 < T1TC)) // Timer 1, Match 2 - 500ms LED Delay <<<<<<<<<<<<<<<<<<<<<< { T1MR2 = T1TC + DEFAULT_TMR1_MR2_TIMEBASE; // Count up to this value. Generate 2 Hz interrupt.


Part ID

Started by Leon Heller in LPC200015 years ago 3 replies

I was curious as to whether the Part ID was unique on every chip, so checked it on two of my boards fitted with '2104s. Both gave...

I was curious as to whether the Part ID was unique on every chip, so checked it on two of my boards fitted with '2104s. Both gave 4293984018. Does anyone know what a '2106 gives? Leon -- Leon Heller, G1HSM Email: My low-cost Philips LPC210x ARM development s


LPC2106 and FPGA

Started by Leon Heller in LPC200014 years ago 18 replies

I am thinking of designing a little 4-layer PCB with an LPC2106 and a Xilinx Spartan XC2S200 on it, for one or two applications I've...

I am thinking of designing a little 4-layer PCB with an LPC2106 and a Xilinx Spartan XC2S200 on it, for one or two applications I've got in mind. The FPGA will be configurable via the '2106 which will have a suitable serial flash device connected to it for storing the configuration data. A


IsoMax for ARM

Started by chazeltopman in LPC200014 years ago 4 replies

For all those programmers out there that wish to explore a new programming paradigm, IsoMax for ARM is available as a preliminary...

For all those programmers out there that wish to explore a new programming paradigm, IsoMax for ARM is available as a preliminary release from New Micros on 2106 and 2129 development boards. While fully functional, the final set of features is still variable and open to sugges


2104 makefile

Started by sanjay_varma_bh in LPC200014 years ago 1 reply

Iam newuser of gcc. I want to work with lpc2104. Unfortunately i could nt get make file for 2104. So I modified the 2106...

Iam newuser of gcc. I want to work with lpc2104. Unfortunately i could nt get make file for 2104. So I modified the 2106 rom.ld,ram.ld to work it for 2104. I just changed the length of SRAM to 16k from 64k. But this is not working. Can anyone help me whe


I2C Help

Started by heedaf in LPC200012 years ago 4 replies

I'm using a Olimex 2106 board as a slave and Embedded Artist 2148 educational board with Crossworks. I'm using TN06005 notes from NXP for the...

I'm using a Olimex 2106 board as a slave and Embedded Artist 2148 educational board with Crossworks. I'm using TN06005 notes from NXP for the slave which is basically a switch statement. It was working fine and I don't know what happened but I'm getting some strange stuff. At one point I couldn't even get the slave to respond so I created a new project and imported everything and that...


external memory interface

Started by rohan patil in LPC200013 years ago 2 replies

i m currently using lpc 2106 for my project is it possible to access external memory using same chip or is there any other...

i m currently using lpc 2106 for my project is it possible to access external memory using same chip or is there any other microcontroller(arm or 8051 core)chip which has on chip flash ram more than 64k please help ********* rohan *******************