Hi all, I bought a Olimex board LPC2378 STK and also Olimex ARM-JTAG(wiggler type) and now not able to establish connection of the JTAG with my...

Hi all, I bought a Olimex board LPC2378 STK and also Olimex ARM-JTAG(wiggler type) and now not able to establish connection of the JTAG with my laptop which doesn't have parallel and serial port.As the JTAG is of wiggler type I am using parallel port to USB converter but still using H-JTAG server is not able to detect the hardware.Please guide me how to make this work on laptop. Thanks, Tush...

Hello Everyone! I have problems to run the example codes (uIP webserver) from Olimex http://www.olimex.com/dev/lpc-p2378.html . on my...

Hello Everyone! I have problems to run the example codes (uIP webserver) from Olimex http://www.olimex.com/dev/lpc-p2378.html . on my LPC2378-Board. Actually i make some improvisation to load this codes to my controller. I don't own IAR Embedded Workbench or J-Link JTAG interface as presupposed. firstl i tried to download the free version of I

Hello, i am trying to initialize USB device block on the Olimex lpc2478 board. i was looking into NXP lpc24xx documentation as well as lpcusb...

Hello, i am trying to initialize USB device block on the Olimex lpc2478 board. i was looking into NXP lpc24xx documentation as well as lpcusb and keil usb code examples but still have no luck. board is booted through u-boot originaly prepared by Olimex (USB host block activated). having look into the NXP docs i am trying to initialize USB port 2 to behave as USB device. also, http://www.olim...

Hi: I am going to interface 2GB SD/MMC card with LPC2378 Processor on Olimex LPC2378STK Board...

Hi: I am going to interface 2GB SD/MMC card with LPC2378 Processor on Olimex LPC2378STK Board (http://www.olimex.com/dev/lpc-2378stk.html). I am new to SD/MMC card, earlier i have interfaced SD/MMC card in SPI mode with LPC2148 processor, with the help of AN10406_3 application note from NXP. This note describe interfacing in SPI mode Please give me link to any document which describe...

Hello everybidy, now I'm a proud owner of an olimex LPC-H2294 board with JTAG wiggler but when I try to execute the blink_led the...

Hello everybidy, now I'm a proud owner of an olimex LPC-H2294 board with JTAG wiggler but when I try to execute the blink_led the compilation fails because of the missing iolpc2294.h, which is part of IAR embedded workbench. I'm using Crossworks 1.42. Can some body give me an example how I can let the LED on PINSEL1 P0.30 (PIN33 / EXT1-28)

Hi, Is anybody developing for the LPC2xxx family using: - Eclipse - openOCD JTAG from Olimex - MAC OS X If so, how do you setup your...

Hi, Is anybody developing for the LPC2xxx family using: - Eclipse - openOCD JTAG from Olimex - MAC OS X If so, how do you setup your environment? Thanks, Jean ------------------------------------

Hello Everybody, I have bought an Olimex LPC-P2129 prototype board, an ARM-JTAG Dongle and I have downloaded a trial version of Rowley...

Hello Everybody, I have bought an Olimex LPC-P2129 prototype board, an ARM-JTAG Dongle and I have downloaded a trial version of Rowley CrossStudio. I am able to write a small program to flash a LED and that works. I am now trying to work with the CAN capabilities of this board, but I can't seem to get it working. Is there maybe someone who can he

Hi, I'm trying to establish connection with Philips Flash Utility and an Olimex 2106 mt board without success. TheBSL jumper is shorted and the...

Hi, I'm trying to establish connection with Philips Flash Utility and an Olimex 2106 mt board without success. TheBSL jumper is shorted and the frequency set at 14745kHz (14.7456MHz). Different baudrates have been tried without success. I am not sure about the DTR/RTS settings however. Also I may be using the wrong RS232 cable. Null modem or not? I'll have to check that. I intend to use the

I am new to the LPC series and using GCC compilers so please forgive me if this is a simple issue. I have managed to configure Eclipse and the...

I am new to the LPC series and using GCC compilers so please forgive me if this is a simple issue. I have managed to configure Eclipse and the associated tools to compile and download code to the Olimex card. After a few days of trial and error I found the following unexplainable operation. The two code fragments below should blink one of the LEDs on the PCB. The only difference is the first o...

I have installed the Olimex ARMUSB-Tiny jtag on my system in an attempt to replace FlashMagic for programing the flash but am having problems. To...

I have installed the Olimex ARMUSB-Tiny jtag on my system in an attempt to replace FlashMagic for programing the flash but am having problems. To minimize the variables I am running ocd in a telnet window with the following service cfg file. -------------------------------------------- #daemon configuration telnet_port 4444 gdb_port 3333 #interface interface ft2232 ft2232_device_desc "Ol...

Hi, I'm new and trying to get started with an LPC2106 (Olimex LPC-P2106 board) and OpenOCD with an Olimex parallel port wiggler. OpenOCD is...

Hi, I'm new and trying to get started with an LPC2106 (Olimex LPC-P2106 board) and OpenOCD with an Olimex parallel port wiggler. OpenOCD is r128 from Yagarto. I'm wondering what I've setup wrong. Sorry for the long length of this post, but I wasn't sure what info would be needed and wanted to provide everything I could think of. I get usually get errors trying to start OpenOCD but if I pres...

Hello all, im kind of confused. I have been skimming throught the user manual for the LPC2103 and can only find that to use debug you should...

Hello all, im kind of confused. I have been skimming throught the user manual for the LPC2103 and can only find that to use debug you should Pull-UP RTCK and DBGSEL... Why in the world does Olimex have so many resistors on the JTAG ? http://www.olimex.com/dev/images/lpc-h2103-sch.gif At the top right either something is pulled high or pulled low... are all these needed? or can i get by w...

Hello, Does anybody in this group own a LPC2138 board from Olimex? I want to try out the sample examples presented on their website and...

Hello, Does anybody in this group own a LPC2138 board from Olimex? I want to try out the sample examples presented on their website and I cant seem to find the required header files. If anyone has a simple working code for LED blinking, I would be thankful if i could get the source with the required header files. -thanks -Pavan ____________________________________________...

hello, i want to interface the port CAN1(DB9) to port CAN2(DB9) in my kit olimex P2129. thank you to give the number of pins to...

hello, i want to interface the port CAN1(DB9) to port CAN2(DB9) in my kit olimex P2129. thank you to give the number of pins to connect ------------------------------------

Hi, Has anyone gotten the Olimex LPC2148 development board and IAR Uart example working for the LPC214X? I can see something with ...

Hi, Has anyone gotten the Olimex LPC2148 development board and IAR Uart example working for the LPC214X? I can see something with hyperterminal, however it is just junk characters. I have tried all available baud rates. Is this code possibly for a specific dev board? This is an initial test to get running, what I really need to do is get FAT16 talking to an sd/MM

Hi all, I am trying to get my hands on a LCD source code for the Olimex E2294 boards. Does anybody know where can I get one? I am using...

Hi all, I am trying to get my hands on a LCD source code for the Olimex E2294 boards. Does anybody know where can I get one? I am using Keil to compile my project. Cheers!

Hi all, I have an olimex lpc2106-mt pcb and try to program a PWM without success. The Docu is not especially detailed (I...

Hi all, I have an olimex lpc2106-mt pcb and try to program a PWM without success. The Docu is not especially detailed (I think). I tried a lot of register settings(for hours). All I get is a single 88.64 ms pulse on PWM4 at reset that does not change with the match register

Hi: I lost a long time trying to debug a simple program reading the Buttons, in the Olimex LPC-P2124/9 boards. Finally, I discovered that ...

Hi: I lost a long time trying to debug a simple program reading the Buttons, in the Olimex LPC-P2124/9 boards. Finally, I discovered that the buttons are not connected to the microcontroller at P0.15 and P0.16, as the board information says. Instead, they use the P0.10 and P0.11 pins Jus in case, I downloaded the information again, but the errors still

Hello All, I am new to the ARM platform, and I'm working on getting my development tools set up. I have I am using the LPC2103 (on olimex...

Hello All, I am new to the ARM platform, and I'm working on getting my development tools set up. I have I am using the LPC2103 (on olimex header board) with the olimex arm-usb-tiny JTAG adapter. I used the included CD to install eclplise, OpenOCD, and the required plugins. The IDE is working well, I can compile C code and debug in eclipse. However, I would also like to be able to write and...

I've been having a heck of a time getting the latest build of OpenOCD to work with a P2478 board, and was wondering if anyone here has had any...

I've been having a heck of a time getting the latest build of OpenOCD to work with a P2478 board, and was wondering if anyone here has had any success configuring with this combination? I'm using OpenOCD 0.1.0 (the latest downloadable binaries), an Olimex ARM-USB-OCD, and an Olimex P2478-STK board. I can get OpenOCD up and running 'seemingly' properly, and can connect over GDB, etc., in Ecli...