BOOT0/BOOT1 on Olimex E2294

Started by davidbinar in LPC200013 years ago

Hi I have the Olimex E2294 board and I'm trying to figure out how the two jumpers for BOOT0 / BOOT1 work. According to the hardware...

Hi I have the Olimex E2294 board and I'm trying to figure out how the two jumpers for BOOT0 / BOOT1 work. According to the hardware description from Olimex you can set the memory width: (BOOT1:BOOT0) 0:0 = 8 bits 0:1 = 16 bits 1:1 = 32 bits But according to the LPC2294 user manual p.122: (BOOT1:BOOT0) 0:0 = 8 bits on CS0 0:1 = 16 bits on CS0 1:0 = 32 bits on CS0 1:1 = Internal f


Olimex lpc2478 stk: USB initialization code

Started by Todorovic Dragan in LPC20009 years ago 6 replies

Hello, i am trying to initialize USB device block on the Olimex lpc2478 board. i was looking into NXP lpc24xx documentation as well as lpcusb...

Hello, i am trying to initialize USB device block on the Olimex lpc2478 board. i was looking into NXP lpc24xx documentation as well as lpcusb and keil usb code examples but still have no luck. board is booted through u-boot originaly prepared by Olimex (USB host block activated). having look into the NXP docs i am trying to initialize USB port 2 to behave as USB device. also, http://www.olim...


SD/MMC driver for Olimex LPC2378STK

Started by sachin kumar in LPC20008 years ago 5 replies

Hi: I am going to interface 2GB SD/MMC card with LPC2378 Processor on Olimex LPC2378STK Board...

Hi: I am going to interface 2GB SD/MMC card with LPC2378 Processor on Olimex LPC2378STK Board (http://www.olimex.com/dev/lpc-2378stk.html). I am new to SD/MMC card, earlier i have interfaced SD/MMC card in SPI mode with LPC2148 processor, with the help of AN10406_3 application note from NXP. This note describe interfacing in SPI mode Please give me link to any document which describe...


USB code for Olimex ?

Started by Ilian in LPC200012 years ago 2 replies

Hi all, Does someone has sample USB codes for Olimex LPC-2378STK board ? I can not receive USB Reset signals and I wish to compare it...

Hi all, Does someone has sample USB codes for Olimex LPC-2378STK board ? I can not receive USB Reset signals and I wish to compare it with some working source codes. Thanks in advance. Ilian


Re: Where can I find olimex LPC-2478STK uCLinux cd?

Started by wmrs...@hotmail.com in LPC20009 years ago 1 reply

Hello guys, I have same problem: -LPC-2478 dev kit from IAR (containing a LPC-2478STK board from Olimex and a J-link from segger. Can...

Hello guys, I have same problem: -LPC-2478 dev kit from IAR (containing a LPC-2478STK board from Olimex and a J-link from segger. Can anyone provide a link from where I can proceed with the download of original documentation/uClinux + u-boot CD from Olimex? Best regards, Marcio Ribeiro Hello there, > > I've recently acquired a LPC-2478 dev kit from IAR (containing a LPC-2478STK


Olimex JTAG

Started by soren_t_hansen in LPC200014 years ago 1 reply

I just bought an Olimex JTAG (Wiggler) and keeps getting the internal error 43 when trying to connect with OCDRemote. I've tested with an ...

I just bought an Olimex JTAG (Wiggler) and keeps getting the internal error 43 when trying to connect with OCDRemote. I've tested with an Ohm-meter to see if there is a connection between pin 8 and 15 on the LPT connector, and it seems as if they are not connected. I found some postings where someone said, that in order to work with OCDRemote versions higher than


olimex board

Started by sandu_deep in LPC20009 years ago 2 replies

Hi I am using LPC2148 olimex board its working fine but the ic is getting heated up and i cheked all pheripharals all are working but adc is...

Hi I am using LPC2148 olimex board its working fine but the ic is getting heated up and i cheked all pheripharals all are working but adc is not working pls sugest me how to over come it ------------------------------------


olimex lpch2214 documentation

Started by ggallant571 in LPC200013 years ago 5 replies

I am looking for documentation for the Olimex LPCH2214 board. Their web site has it as .chn but I get "unable to access" messages. I do get ...

I am looking for documentation for the Olimex LPCH2214 board. Their web site has it as .chn but I get "unable to access" messages. I do get the top level index info. George


how to use olimex lpc-p278stk

Started by william cheng in LPC200012 years ago 1 reply

Hi, I am a newbie to arm. just bought a lpc-p278stk and a arm-jtag from olimex but it comes with no documentations at all. Can anyone...

Hi, I am a newbie to arm. just bought a lpc-p278stk and a arm-jtag from olimex but it comes with no documentations at all. Can anyone give me pointers to howto use these type of boards. Thank you very much ...William


Yargato and OpenOCD with Olimex usb ocd

Started by jdauchot in LPC200010 years ago 1 reply

Hi I have installed the Olimex OCD drivers etc and I would like to use it with the Yargato Eclipse Dev tools Can someone please explain...

Hi I have installed the Olimex OCD drivers etc and I would like to use it with the Yargato Eclipse Dev tools Can someone please explain how to interface with the OpenOCD with this IDE. As I try to follow the instructions which does not match what I see on the screen Regards Jean-Jacques ------------------------------------


Problems programming external flash on olimex eval board using CrossWorks IDE

Started by chilliepepper432 in LPC200011 years ago

Hi. I have been trying to program the external flash on an Olimex LPC- H2214 HEADER BOARD with no success. I have been successfull in using...

Hi. I have been trying to program the external flash on an Olimex LPC- H2214 HEADER BOARD with no success. I have been successfull in using CrossWorks to program and debug using internal RAM and internal flash. I am using the LPC-E2214 board support package from Rowley. My Olimex eval board has a 26LV800BTC-55 flash part installed on it. This is such an un-common part that it is difficu...


Olimex LPC-H2294 Example

Started by thomas_ploeger in LPC200013 years ago 5 replies

Hello everybidy, now I'm a proud owner of an olimex LPC-H2294 board with JTAG wiggler but when I try to execute the blink_led the...

Hello everybidy, now I'm a proud owner of an olimex LPC-H2294 board with JTAG wiggler but when I try to execute the blink_led the compilation fails because of the missing iolpc2294.h, which is part of IAR embedded workbench. I'm using Crossworks 1.42. Can some body give me an example how I can let the LED on PINSEL1 P0.30 (PIN33 / EXT1-28)


Eclipse+Olimex openOCD+MAC OS X

Started by Jean-Sebastien Stoezel in LPC200010 years ago 23 replies

Hi, Is anybody developing for the LPC2xxx family using: - Eclipse - openOCD JTAG from Olimex - MAC OS X If so, how do you setup your...

Hi, Is anybody developing for the LPC2xxx family using: - Eclipse - openOCD JTAG from Olimex - MAC OS X If so, how do you setup your environment? Thanks, Jean ------------------------------------


LPCE2214

Started by vennela2214 in LPC200013 years ago 3 replies

I have purchased LPCE2214 testing board from OLIMEX. Iam able to power up this board and check the test routien given by OLIMEX. I have couple...

I have purchased LPCE2214 testing board from OLIMEX. Iam able to power up this board and check the test routien given by OLIMEX. I have couple of questions on this.. How would I know what RTOS is built in by default in this board.? I would like to port new OS in to this.. if this is the case how can i copy the old one for future purposes. If any body has any guidelines or steps in porting


CAN on LPC2378

Started by jefspalace in LPC200012 years ago 2 replies

Hi all, I read in several fora that there exist problems with CAN on LPC2378. Some of them seemed to be related to electrical issues...

Hi all, I read in several fora that there exist problems with CAN on LPC2378. Some of them seemed to be related to electrical issues others due to software bugs. I am planning on buying an Olimex 2378 board but they mailed that they don't test CAN. Is there anybody out there who can confirm CAN is working on LPC2378 in general and/or on the Olimex development board LPC-2378STK....


Olimex LPC-P2129 CAN example

Started by eabesselsen in LPC200013 years ago 1 reply

Hello Everybody, I have bought an Olimex LPC-P2129 prototype board, an ARM-JTAG Dongle and I have downloaded a trial version of Rowley...

Hello Everybody, I have bought an Olimex LPC-P2129 prototype board, an ARM-JTAG Dongle and I have downloaded a trial version of Rowley CrossStudio. I am able to write a small program to flash a LED and that works. I am now trying to work with the CAN capabilities of this board, but I can't seem to get it working. Is there maybe someone who can he


Olimex LPC2106mt bootloader problem

Started by Anders Kjellberg in LPC200013 years ago 16 replies

Hi, I'm trying to establish connection with Philips Flash Utility and an Olimex 2106 mt board without success. TheBSL jumper is shorted and the...

Hi, I'm trying to establish connection with Philips Flash Utility and an Olimex 2106 mt board without success. TheBSL jumper is shorted and the frequency set at 14745kHz (14.7456MHz). Different baudrates have been tried without success. I am not sure about the DTR/RTS settings however. Also I may be using the wrong RS232 cable. Null modem or not? I'll have to check that. I intend to use the


LPC2478 loop and LED on Olimex SDK

Started by "jim.deas" in LPC200010 years ago 2 replies

I am new to the LPC series and using GCC compilers so please forgive me if this is a simple issue. I have managed to configure Eclipse and the...

I am new to the LPC series and using GCC compilers so please forgive me if this is a simple issue. I have managed to configure Eclipse and the associated tools to compile and download code to the Olimex card. After a few days of trial and error I found the following unexplainable operation. The two code fragments below should blink one of the LEDs on the PCB. The only difference is the first o...


Just got a quote for LPC-P1 (prototyping board with LPC2106) from Olimex in Germany

Started by Anonymous in LPC200015 years ago 1 reply

Hello, perhaps interesting for you if you search for a prototyping board here in Germany: ...

Hello, perhaps interesting for you if you search for a prototyping board here in Germany: http://www.olimex.com/dev/lpc-p1.html Just got an email from http://www.elektron


Optimization problem

Started by andersryl in LPC200013 years ago 2 replies

Hi, I have a weird problem (hmmm, what problems aren't weird?) regarding the optimization flag in GCC. I use GNUARN 4.0.1, Eclipse...

Hi, I have a weird problem (hmmm, what problems aren't weird?) regarding the optimization flag in GCC. I use GNUARN 4.0.1, Eclipse 3.0.1 and an board from Olimex for my project. The Olimex-uC talks to a PC-app via UART 1. Work is progreesing but then I got a Data Abort interrupt indicating something was wrong. So my idea was t