EmbeddedRelated.com
The 2024 Embedded Online Conference

Launchpad Prototyping capes?

Started by "Ste...@gmail.com [msp430]" in MSP43010 years ago 19 replies

Hello everyone, I want to buy a couple of prototyping boards (capes?) for the MSP430. What I need is an equivalent to the Arduino prototyping...

Hello everyone, I want to buy a couple of prototyping boards (capes?) for the MSP430. What I need is an equivalent to the Arduino prototyping shields, i.e, a PCB which will plug into the Launchpad board with a proto typing area which I can solder components to or put a small plugboard on to. Do they exist and can I purchase them in the UK? Thanks, Steve G0XAR


Hex file installer

Started by robe...@dcsi.net.au in MSP43010 years ago 9 replies
IAR

Hello Group, I'm a long time listener and first time poster, pretty well up with the hardware side of MCU's but lack a fair bit of knowledge on...

Hello Group, I'm a long time listener and first time poster, pretty well up with the hardware side of MCU's but lack a fair bit of knowledge on the software side, hence my question today... Does the MSP430 Lauchpad have a hex file downloader ? ( not comparing the MSP430 to PIC or AVR but they have software that does just that ) I've downloaded and looked CCS 5.5, IAR 5 and Energia and cant se...


MSP430F5438A eeprom isr works ONLY with extra print statements??

Started by mrai...@hofferflow.com in MSP43010 years ago 5 replies

Hi Folks, I am attempting to write/read a Microchip 24FC1025 eeprom using the intrinsic i2c on a Texas Instruments MSP430F5438A chip. This...

Hi Folks, I am attempting to write/read a Microchip 24FC1025 eeprom using the intrinsic i2c on a Texas Instruments MSP430F5438A chip. This may be a mistake because I got no hits when searching the Microchip forum for msp430 or F5438. Has anyone done this successfully and, if so, what are the pitfalls to watch out for? It is my understanding that this eeprom has two slave addresses...


IAR - watch window to clipboard/file

Started by Darren Logan in MSP43010 years ago 3 replies
IAR

Hi all, Does anyone know if there's any way to save the contents of the IAR (v5.30) watch window to Windows clipboard or a text...

Hi all, Does anyone know if there's any way to save the contents of the IAR (v5.30) watch window to Windows clipboard or a text file? Thanks Best regards, Darren


ECG code for ez430-rf2500

Started by Ahmad Bin Javed in MSP43010 years ago 4 replies

i am using ez430 in a project, it is equipped with msp430F2274 microcontroller. My signal has a peak frequency of 40hz. i will take data...

i am using ez430 in a project, it is equipped with msp430F2274 microcontroller. My signal has a peak frequency of 40hz. i will take data continously from one pin and transmit data after sampling it ... i need code for this in which sampling rate is 90 samples/second.


TI I2C Example Problems

Started by mrai...@hofferflow.com in MSP43010 years ago 15 replies

Hey Folks, Some of you may remember I just had a problem bit-banging an i2c interface to an eeprom, Microchip 24FC1025. That problem...

Hey Folks, Some of you may remember I just had a problem bit-banging an i2c interface to an eeprom, Microchip 24FC1025. That problem remains unsolved, with IAR and myself continuing to work on it, but right now, I am trying to interface with the eeprom using the TI built-in I2C USCIB2. I have been fighting to make a very simple (I thought) TI example titled "MSP430x54x_uscib0_i2...


Brief Introduction

Started by kuka...@yahoo.com in MSP43010 years ago 4 replies

Hi I need books or sth like that which introduce MSP430 from A to Z I am very new to it so it is to hard to understand for me. It could be in...

Hi I need books or sth like that which introduce MSP430 from A to Z I am very new to it so it is to hard to understand for me. It could be in English, Turkish or Russian languages. Thank you for your help in advance.


MSp430 stack tracing

Started by july...@gmail.com in MSP43010 years ago 2 replies

Hi I am using CCS version 5. I want to check if my stack allocation is correct or not? i had done some testing by directly writing into stack...

Hi I am using CCS version 5. I want to check if my stack allocation is correct or not? i had done some testing by directly writing into stack area and check the value in debugger. is there a way through which CCS can generate some information like which function is going to use how much stack. thanks for the help.


WEIRD BEHAVIOUR OF IAR (YET AGAIN)

Started by Onestone in MSP43010 years ago 14 replies

I've gone back to an older design to upgrade the software. The design uses an MSP430F149. A couple of months ago I upgraded Kickstarter to...

I've gone back to an older design to upgrade the software. The design uses an MSP430F149. A couple of months ago I upgraded Kickstarter to slac050aq, or version 5.52. It seemed to be OK for the newer micros I was working with, but now it seems to be behaving strangely. It won't revert to compiler mode from debug mode, it crashes. It doesn't seem to recognise or act on most breakpoints, i...


ohm meter using msp430

Started by ee13...@ee.iitm.ac.in in MSP43010 years ago 14 replies

I am new to MSP. i want to design an Ohm meter using MSP 430. Can anyone suggest how do I start... ------------------------------------ Yahoo...

I am new to MSP. i want to design an Ohm meter using MSP 430. Can anyone suggest how do I start... ------------------------------------ Yahoo Groups Links To visit your group on the web, go to: http://groups.yahoo.com/group/msp430/ Your email settings: Individual Email | Traditional To change settings online go to: http://groups.yahoo.com/group/msp430/join


Ask a Question to the EmbeddedRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright


The 2024 Embedded Online Conference