ICD2Clone dont work ??

Started by Luis in Piclist10 years ago 1 reply

hi all, I?m build the icd2clone, in WindowsXP it?s ok, but in MPLAB: MPLAB ICD 2 Ready Downloading Operating System Connecting to MPLAB ICD...

hi all, I?m build the icd2clone, in WindowsXP it?s ok, but in MPLAB: MPLAB ICD 2 Ready Downloading Operating System Connecting to MPLAB ICD 2 ...Connected ICDWarn0054: MPLAB IDE has lost communications with the MPLAB ICD 2. Would you like to attempt to reconnect? Connecting to MPLAB ICD 2 ...Connected ICD0082: Failed MPLAB ICD 2 operation ICD0082: Failed MPLAB ICD 2 operation ...Dow...


ICD software re-download help

Started by cxiong2k in Piclist14 years ago

I have an ICD from MICROCHIP and use it with the CCS PCM software, When I complete the code and try to program the target board...

I have an ICD from MICROCHIP and use it with the CCS PCM software, When I complete the code and try to program the target board with the CCS ICD software. I have mistake upgrade the firmware to CCS ICD-s. I want to put it back to the MICROCHIP version. What should I do? Anybody he


What to do with your ICD 1 for debugging 16F88

Started by scott5342000 in Piclist13 years ago

I have an ICD 1 I would like to use on 16F88 & 16F7x7's. Anyone try using an ICD 1 on any of those PIC's that are not supported on...

I have an ICD 1 I would like to use on 16F88 & 16F7x7's. Anyone try using an ICD 1 on any of those PIC's that are not supported on MPLab 5.7? I was told that a CCS firmware load could enable it to download programs, but I would like to be able to debug too. So I would like a


ICD 2 support for 16F628?

Started by Dennis Clark in Piclist13 years ago 2 replies

Hi all, I've got an issue. My ICD-2 on MPLAB 6.60 says that the programmer won't support the 16F628. The MC website says it...

Hi all, I've got an issue. My ICD-2 on MPLAB 6.60 says that the programmer won't support the 16F628. The MC website says it will program it, but not debug it without an adapter. OK, since my IDE refuses to let me choose the ICD-2 as my programmer, it is obvious which way the w


CCS ICD-U/S question

Started by guillaumedubos in Piclist13 years ago 10 replies

Hi Group, I've read the CCS website info about the CCS ICD-U/S programmer- debugger and I'm looking for more information or...

Hi Group, I've read the CCS website info about the CCS ICD-U/S programmer- debugger and I'm looking for more information or experience about this product. In fact I don't understand if this ICD needs or not CCS PCW to have access to the real time debug capabilities (which wou


Can an ICD 1 be modified to program 16F88 & 16F7X7's, or should I go for an AVR?

Started by scott5342000 in Piclist13 years ago 3 replies

I can't upgrade to MPLab 6.x and use my ICD 1. I don't want to cough up $180 for a new ICD 2. Someone know how to modify...

I can't upgrade to MPLab 6.x and use my ICD 1. I don't want to cough up $180 for a new ICD 2. Someone know how to modify MPLab 5.x and/or reprogram an ICD1? I see Atmel is giving away AVR JTAGICE in-circuit debuggers at their seminars. AVR's look like they have m


Opinions on the best PIC BASIC compiler?

Started by Bob Hyland in Piclist10 years ago 6 replies

I've been looking at different PIC BASIC compilers. What I am looking for: - Performance (efficient code) - ICD (in circuit debugging) -...

I've been looking at different PIC BASIC compilers. What I am looking for: - Performance (efficient code) - ICD (in circuit debugging) - Good support for a wide variety of MicroChip MPU's So far, I am considering the following compilers: - PIC BASIC PRO (seems like their ICD is limited to a few chips?) - mikroBasic (built in ICD support) - Proton PIC Basic (http://www.protongeeks.com/...


ICD questions

Started by Phil in Piclist14 years ago 1 reply

I've been thinking about getting an ICD and would like to get people's opinions. I've done a bunch of searching and this seems to ...

I've been thinking about getting an ICD and would like to get people's opinions. I've done a bunch of searching and this seems to be a non-topic of discussion... As I understand it, there are 2 versions: ICD1 (olimex board) and ICD2 (Microchip). ICD1 only works with a coupl


ICD 2 and 18F1220 problems

Started by tadaosystems in Piclist13 years ago 2 replies

Has anyone used the ICD 2 with a pic18f1220? I'm having trouble just reliably programming the 1220s. Seems to be hit or miss...

Has anyone used the ICD 2 with a pic18f1220? I'm having trouble just reliably programming the 1220s. Seems to be hit or miss (sometimes it's fine, other times it gives me a verify failed error on the program memory space). I'm using win2k server, the usb connection, an exte


ICD2 Busy and Hung

Started by scottmack1 in Piclist10 years ago

I am having some kind of problem with the communications to the ICD2. When I start MPLAB IDE v7.60 with the ICD2 plugged in my computer's USB...

I am having some kind of problem with the communications to the ICD2. When I start MPLAB IDE v7.60 with the ICD2 plugged in my computer's USB port and the ICD2 plugged into my pcb (PIC16F887), it connects OK, reads ICD Product ID, runs the ICD self test, passed, says MPLAB ICD2 Ready but continues to have the Busy led on the ICD2 blinking. If I click in the program window or around on ...


Before I use ICD to program the PIC16F877A,a strange message occur.

Started by Bruce.J Sam in Piclist13 years ago

     My PIC code was not exceed <1FFF>,but when I pressed the button of "program" in the dialogbox of ICD option.A message pop-up,liked...

     My PIC code was not exceed <1FFF>,but when I pressed the button of "program" in the dialogbox of ICD option.A message pop-up,liked this:There are more program codes at <2000> after End Address <1FFF>.Continue to Program?So I pressed the "Yes",and the program proce


Opinions? Using the ICD2/Picdem2 as a programmer

Started by iphillipsca in Piclist13 years ago

I am about to start producing some products (small quantities) and was wondering if anybody out there has done such a thing? I...

I am about to start producing some products (small quantities) and was wondering if anybody out there has done such a thing? I have the Microchip ICD kit. My one concern is if the application uses certain pins that the Picdem board uses for something else could this cause a


ICD-2 Problems

Started by Fredrik Krook in Piclist14 years ago 4 replies

Hi! I?m trying to program a circuit... 16F877 and then run it in debugmode... But it doesn?t work... getting the errors listed...

Hi! I?m trying to program a circuit... 16F877 and then run it in debugmode... But it doesn?t work... getting the errors listed below... Does anyone know how to get it to work... Programming Target... ...Erasing Part ...Programming EEPROM Memory


Orging at what address

Started by bg3009 in Piclist14 years ago

A very fundamental question guy.. I am trying to use the ICD with my own target app. The thing i know is we should org at some...

A very fundamental question guy.. I am trying to use the ICD with my own target app. The thing i know is we should org at some other address and NOT 0x00. Has anyone got any idea what address we should org at? How much space the debug exec shld have? My code starts as follows..


Reset on Halt or on Breakpoints

Started by scottmack1 in Piclist9 years ago

Guys, I am using a 16F887 with MPLAB 7.60 and a ICD 2. I need to continue coding on a project I worked on a while back. Jumping in and fixing...

Guys, I am using a 16F887 with MPLAB 7.60 and a ICD 2. I need to continue coding on a project I worked on a while back. Jumping in and fixing stuff I have managed to get into some kind of mess. The cpu seems to always reset to the beginning of the program when I halt it. I kind of figured this may be do to using the WDT & SLEEP combination, not sure, and that I have something wrong the...


ICSP Programming CCS

Started by Scott Lingerfelt in Piclist13 years ago

I currently have my hardware setup with ICSP. I use the MCLR, B6, B7 and connect B3 to ground. I am using the Epic programmer to...

I currently have my hardware setup with ICSP. I use the MCLR, B6, B7 and connect B3 to ground. I am using the Epic programmer to program my hardware at this time. Everything works fine. My question is I have just purchased the CCS compiler and an ICD-40U to use for prog


18F1220 once again...

Started by tadaosystems in Piclist13 years ago 14 replies

I'm just having difficulties getting an 18F1220 to run a simple program. I'm using HT PICC18 with an ICD 2. My...

I'm just having difficulties getting an 18F1220 to run a simple program. I'm using HT PICC18 with an ICD 2. My configuration bits: __CONFIG(1, RCIO & IESOEN & FCMDIS); // internal oscillator with RA6 digital i/o __CONFIG(2, BORV42 & PWRT


Macintosh Virtual PC MPLAB and the ICD2 on USB, works?`

Started by Dennis Clark in Piclist12 years ago

Hi all, I'm movinf from my cranky PC's to the Mac, and some things don't have open source or Unix options, like MPLAB. While I've...

Hi all, I'm movinf from my cranky PC's to the Mac, and some things don't have open source or Unix options, like MPLAB. While I've gotten compilers and MPLAB to work on Virtual PC 7 (Windows 2K) through the serial port, I'd REALLY like to get the ICD 2 working via USB. Has anyone gotten this to work and would be willing to share tips? The silence on


usart PIC16F877

Started by fish_camera in Piclist10 years ago 4 replies

Attempting to troubleshoot problem with usart, asynchronous mode, for a school project. Two 16F877. Using the ICD-2 in circuit debugger. We...

Attempting to troubleshoot problem with usart, asynchronous mode, for a school project. Two 16F877. Using the ICD-2 in circuit debugger. We believe our transmit chip is working but we can't get receive to function correctly. We know interupts will not work while Single stepping in debug mode, but in animate mode interupts should function, correct? How close do the clocks have to be? ...


Breakpoints in MPLAB

Started by Basic Poke in Piclist9 years ago 1 reply

I am having a rough time with the breakpoints in MPLAB 8.10, using MPLAB ICD 2 as the debugger. The debugger will often stop at the line...

I am having a rough time with the breakpoints in MPLAB 8.10, using MPLAB ICD 2 as the debugger. The debugger will often stop at the line after the breakpoint, but sometimes right on it, and sometimes on some other line near the breakpoint. Sometimes when I put a breakpoint on a function call, it will stop at the function header (for example "void InitializeMCU (void)"). And the Step-O...