MPLAB v7.01

Started by kg4pid in Piclist13 years ago 1 reply

I just downloaded and installed verson 7.01 of MPLAB. So far the only problems I've had is that it doesen't erase the chip...

I just downloaded and installed verson 7.01 of MPLAB. So far the only problems I've had is that it doesen't erase the chip before programming. First time I used it to program a chip with the picstart plus it gave me alot of errors. I thought I had a bad chip. But after era


PIC programmer

Started by saurabhgupta_ece2005 in Piclist10 years ago 1 reply

hello everyone. i am new to PIC microcontroller,so i need help. However i have a lot of experience on avr microcontroller but now i want to...

hello everyone. i am new to PIC microcontroller,so i need help. However i have a lot of experience on avr microcontroller but now i want to work on PIC. i need to know about some homebrew programmer for 16-bit PIC24FJ64GA002 microcontroller. i want to program it without using the costly readymade PICSTART programmer Kit or something like this. So can someone please tell me the link or s...


PIC18F452 for Qwikflash

Started by Mohammad Tariq Iqbal in Piclist13 years ago

Hi I am trying to program PIC18F452 for Qwikflash board. (picbook.com) I am using picstart plus programmer. I progrmmed...

Hi I am trying to program PIC18F452 for Qwikflash board. (picbook.com) I am using picstart plus programmer. I progrmmed qfpv.hex into PIC and it works fine. But when I programmed PIC with QB124.hex and linked qwikflash with a PC running Tera Term Pro then it does not


Warp13 OR Picstart plus

Started by AMIT KAPOOR in Piclist13 years ago 3 replies

Hello everyone , i need your guidance . actually till now i was using pic16 series and i have programmer which support...

Hello everyone , i need your guidance . actually till now i was using pic16 series and i have programmer which support only pic12/14/16 series. but now i want to jump to pic18 series so i need to buy pic18 programmer.i searched and found that there are two programmer :


Wake Up On Key Stroke

Started by jmsmith871 in Piclist9 years ago 2 replies

Although I've been using PICs for years, I'm only now studying the SLEEP instruction and code to wake up the processor. It's not going well at...

Although I've been using PICs for years, I'm only now studying the SLEEP instruction and code to wake up the processor. It's not going well at the moment. Microchip's app note AN552, "Implementing Wake-up on Key Stroke," has sample code for a 16C71. I pasted the code into the MPLAB IDE, and it assembled without errors. A PICStart Plus programmed it into a 16C71 with no errors. However,...


Question Re: WARP-13a Programmer and MPLAB

Started by bob_ledoux in Piclist13 years ago

The programmer is working, but reports blank chips, as not blank. I've upgraded my WARP-13a firmware to "R28" using the...

The programmer is working, but reports blank chips, as not blank. I've upgraded my WARP-13a firmware to "R28" using the chip and resonator set from Peter H. Anderson (Phanderson.com). I'm running MPLAB v5.70.40, using the WARP-13a as a PicStart


Repairing the Picstart plus

Started by Milton Medicinteknik KB in Piclist15 years ago 1 reply

Hi out there,   I know this might me the wrong spot i cyberspace for this issue, but I'll give it a go anyway: ...

Hi out there,   I know this might me the wrong spot i cyberspace for this issue, but I'll give it a go anyway: Has anyone "been-there-done-that


Linux alternatives to MPLAB

Started by Jason Hsu in Piclist9 years ago 9 replies

I have a PICSTART Plus programmer with a serial port. So far, I have used MPLAB in Windows to program microcontrollers in Assembly...

I have a PICSTART Plus programmer with a serial port. So far, I have used MPLAB in Windows to program microcontrollers in Assembly language. What are my options for programming microcontrollers in Assembly language with Damn Small Linux as the OS? What are my options for programming microcontrollers in C with Damn Small Linux as the OS? ------------------------------------