Run Time Error

Started by "see...@yahoo.com [rabbit-semi]" in Rabbit-Semi2 years ago 3 replies

I tried running the DC v9.62 debugger on an RCM3000 module with a program that has been running for years. DC loads the firmware and when it's...

I tried running the DC v9.62 debugger on an RCM3000 module with a program that has been running for years. DC loads the firmware and when it's done I get the following error message before it closes: Run Time Error: An RST 38 occurred, but the RST 38 vector is uninitialized. Address 00:e5cf I've never seen that error before. Anyone know what it means or at least how to solve it?


LED TCP/IP OFF

Started by "S S...@gmail.com [rabbit-semi]" in Rabbit-Semi2 years ago 1 reply

Dear All, I'm use RCM3700 dan DC9.62. I'm ping system and replay, result pd_havelink() = 1. If connector tcp/ip pull out, result = 0. I have...

Dear All, I'm use RCM3700 dan DC9.62. I'm ping system and replay, result pd_havelink() = 1. If connector tcp/ip pull out, result = 0. I have digital input and use opto for isolation. Digital input connect to contact of contactor. If contactor on and off repeated, led tcp/ip off and ping RTO. In monitor pd_havelink(), result = 1. If connector tcp/ip pull out, result still = 1. Can anyone...


how to tell near from far pointers

Started by "tit...@gmail.com [rabbit-semi]" in Rabbit-Semi2 years ago 4 replies

Does anybody know what is the standard way to tell if a pointer can be safely casted to near? Here is a sample program: #include...

Does anybody know what is the standard way to tell if a pointer can be safely casted to near? Here is a sample program: #include "xbee/platform.h" void my_dump(void far *address) { const char far *data = address; printf("Address %" PRIpFAR, data); printf(" contains: 0x%02" PRIX8 ".\n", data[0]); } char far f[64]; char n[64]; void main () { f[0] = ...


difference between IntervalMs and DelayMs

Started by "yan...@omniverter.com [rabbit-semi]" in Rabbit-Semi2 years ago 1 reply

Hello, I have couple costate loop. When I use wait(DelayMs(500)) after task is finished and make costate to wait, sometimes my controller is...

Hello, I have couple costate loop. When I use wait(DelayMs(500)) after task is finished and make costate to wait, sometimes my controller is frozen, but when I use wait(IntervalMs(500)), it seems controller is working properly. Does any body know the difference between these two functions? Thanks a lot.


Analog reading in BL4S200

Started by "yan...@omniverter.com [rabbit-semi]" in Rabbit-Semi2 years ago 1 reply

Hello, I am using BL4S200 for my voltage monitoring system.I have a AC voltage transducer, It can monitor AC line voltage and output is RMS...

Hello, I am using BL4S200 for my voltage monitoring system.I have a AC voltage transducer, It can monitor AC line voltage and output is RMS value (DC linear output from 0 to 10VDC), So input is 0..300VAC, and output is 0..10VDC (RMS value). When I try to connect output of transducer to BL4S200 analog input, and I set single end unipolar 0..10VDC, I calibrate channel, I am able to have reading, ...


switch vs router

Started by "see...@yahoo.com [rabbit-semi]" in Rabbit-Semi2 years ago 2 replies

If you use a 3-layer switch instead of a router to connect to equipment on a different network, does that affect the network configuration of a...

If you use a 3-layer switch instead of a router to connect to equipment on a different network, does that affect the network configuration of a Rabbit? I wouldn't think so, but I'm not clear on the differences between routers and L3 switches.


Program Memory

Started by "see...@yahoo.com [rabbit-semi]" in Rabbit-Semi2 years ago 9 replies

I think some of this has been talked about before, but I'm not finding any answers, just flames. I have an application that runs on an RCM3900....

I think some of this has been talked about before, but I'm not finding any answers, just flames. I have an application that runs on an RCM3900. Over the years the size of the app has increased little by little as features were added. Yesterday I made the latest change, programmed a module, and nothing. Program wouldn't run. I backed out the change and it runs. I add the change back in and r...


FIRMWARE VERSION INFOMATION

Started by "yan...@omniverter.com [rabbit-semi]" in Rabbit-Semi2 years ago 3 replies

Hi: We can use fiProgramInfo to get firmware information, but it looks we only get a read only copy. the frimware information, there are some...

Hi: We can use fiProgramInfo to get firmware information, but it looks we only get a read only copy. the frimware information, there are some user define parts, is it possible modify user define parts?


DC and rabbitlib

Started by "Mas...@micronengineering.it [rabbit-semi]" in Rabbit-Semi2 years ago 3 replies

Hello all, I am not using DC since 2006 and now I need to do a short modification on a Rabbit RCM board. 1. Last release I have is DC 10,...

Hello all, I am not using DC since 2006 and now I need to do a short modification on a Rabbit RCM board. 1. Last release I have is DC 10, is there something new compatible with it? 2. I didn't remember where I downloaded rabbitlib a zip containing some libs don't published by Z-World/Digi, can anyone point me where can I download it? Kind regards, --- Questa e-mail ? stata controlla...


save memory into backup ram

Started by "yan...@omniverter.com [rabbit-semi]" in Rabbit-Semi2 years ago 1 reply

Hello, everybody: I have some parameters in BL4S200, user will change them from HMI, and I want to save this change, so program can use them...

Hello, everybody: I have some parameters in BL4S200, user will change them from HMI, and I want to save this change, so program can use them after controller power on next time. I find bbram and protected, but I am not very clear how to use it? does anybody give me a sample for that?


Ask a Question to the EmbeddedRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright