maximili wrote:
>> maximili wrote:
>>> Hi all. I have just purchased the omnivision 9650 cmos camera for my
>>> project of image processing and i wish to interface the camera with the
>>> Altera DE2 FPGA board. For this I need to write the configuration in
>>> verilog code program but I do not have a clue about how to write it.
> Can
>>> anyone here provide any guidance? Thanks a lot.
>> Do you have the full data sheet for the OV9650? After you sign their 
>> NDA, OmniVision will send it to you. You'll also want to download the 
>> SCCB spec, although it's a pretty simple 2 0r 3 wire serial protocol.
>>
>> http://www.ovt.com/products/sccbspec_an_2_1.pdf
>>
>> After you have the docs, I would suggest setting up an environment that 
>> will allow you to easily change registers in the imager and display the 
>> results. There are many, many registers in these things and I didn't 
>> find it obvious which ones did what.
>>
>> HTH,
>> Bob
> 
> 
> 
> Sorry for the late reply, and thanks a lot Bob, I have the data sheet, and
> I have try write up a SCCB verilog HDL program with the reference to
> another of similar Omnivision product, the OV7720 camerachip's SCCB
> program. But there are two questions I have in mind, 

So you haven't started, yet?

> 1. Is the SCCB.v program for the OV7720 camerachip will also work with
> Ov9650 camerachip or does two program bear any similarity so that I could
> refer to that?

If the 9650 data sheet says it uses the same SCCB protocol, then it 
probably does.

> 2. When I have done the SCCB.v code, should I write another module to
> initialize the camera with the settings I want? I found it hard to
> understand the 2-phase write and read cycle...

Write another module or put it into the same module - organize your code 
any way that you want.

> I really need help to get this camera work by this week...Hope to get some
> help from pros here! Thanks!	   
I already suggested a course of action but you don't appear to have made 
any progress in 2 months. good luck,
Bob

>maximili wrote:
>> Hi all. I have just purchased the omnivision 9650 cmos camera for my
>> project of image processing and i wish to interface the camera with the
>> Altera DE2 FPGA board. For this I need to write the configuration in
>> verilog code program but I do not have a clue about how to write it.
Can
>> anyone here provide any guidance? Thanks a lot.
>
>Do you have the full data sheet for the OV9650? After you sign their 
>NDA, OmniVision will send it to you. You'll also want to download the 
>SCCB spec, although it's a pretty simple 2 0r 3 wire serial protocol.
>
>http://www.ovt.com/products/sccbspec_an_2_1.pdf
>
>After you have the docs, I would suggest setting up an environment that 
>will allow you to easily change registers in the imager and display the 
>results. There are many, many registers in these things and I didn't 
>find it obvious which ones did what.
>
>HTH,
>Bob



Sorry for the late reply, and thanks a lot Bob, I have the data sheet, and
I have try write up a SCCB verilog HDL program with the reference to
another of similar Omnivision product, the OV7720 camerachip's SCCB
program. But there are two questions I have in mind, 

1. Is the SCCB.v program for the OV7720 camerachip will also work with
Ov9650 camerachip or does two program bear any similarity so that I could
refer to that?

2. When I have done the SCCB.v code, should I write another module to
initialize the camera with the settings I want? I found it hard to
understand the 2-phase write and read cycle...

I really need help to get this camera work by this week...Hope to get some
help from pros here! Thanks!	   
					
---------------------------------------		
Posted through http://www.EmbeddedRelated.com

maximili wrote:
> Hi all. I have just purchased the omnivision 9650 cmos camera for my
> project of image processing and i wish to interface the camera with the
> Altera DE2 FPGA board. For this I need to write the configuration in
> verilog code program but I do not have a clue about how to write it. Can
> anyone here provide any guidance? Thanks a lot.

Do you have the full data sheet for the OV9650? After you sign their 
NDA, OmniVision will send it to you. You'll also want to download the 
SCCB spec, although it's a pretty simple 2 0r 3 wire serial protocol.

http://www.ovt.com/products/sccbspec_an_2_1.pdf

After you have the docs, I would suggest setting up an environment that 
will allow you to easily change registers in the imager and display the 
results. There are many, many registers in these things and I didn't 
find it obvious which ones did what.

HTH,
Bob

Hi all. I have just purchased the omnivision 9650 cmos camera for my
project of image processing and i wish to interface the camera with the
Altera DE2 FPGA board. For this I need to write the configuration in
verilog code program but I do not have a clue about how to write it. Can
anyone here provide any guidance? Thanks a lot.

	   
					
---------------------------------------		
This message was sent using the comp.arch.embedded web interface on
http://www.EmbeddedRelated.com