Reply by n.na...@gmail.com●June 13, 20082008-06-13
Thanks to all of you.
Nandini
>Hi all. I am working with ATMEGA169 microcontroller. I
am using a battery to provide supply to the board.I am uisng ISL6292 battery
charger. A TEMP pin of the charger monitors the battery temperature to ensure a
safe charging temperature range. This TEMP pin is connected to ATMEGA. Some
voltage is appearing on this pin from this voltage how to calculate the
temperature.
>
>
Reply by raj●June 10, 20082008-06-10
Dear Nandini,
If some voltage is appearing then in the datasheet it should must be
given that how much rise in temp equals the voltage for ex LM535 temp sensors
from Natioanal semi.So check D/S of your Bat charger.For any clarification write
to me ASAP.
Nandini, where are you working? can you help me, u can!
can you send me a circuit of power supply particularly using Micros like tiny
and mega. I need this one. pls help me out!
My Alt id.: k...@gmail.com
Rgds....
Kundan
On Mon, 09 Jun 2008 n...@gmail.com wrote : >
>Hi all. I am working with ATMEGA169 microcontroller. I am using a battery to
provide supply to the board.I am uisng ISL6292 battery charger. A TEMP pin of
the charger monitors the battery temperature to ensure a safe charging
temperature range. This TEMP pin is connected to ATMEGA. Some voltage is
appearing on this pin from this voltage how to calculate the temperature. Sr. FAE
Excel Eltech inc.
A-76, EOK. New Delhi
110065
ph:9811675688
Reply by Csaba Zvekan●June 9, 20082008-06-09
The temperature sensor in this device is designed to measures the
temperature of the charged battery. Once they reached a specific
temperature it will shut off. Kind of like a safety feature
If you just want to measure ambient temperature look into the
DS18B20 , DS1820 etc. They are One Wire connections and have plenty of
programs for AVR MCU's that cover them.
:)
Csaba
On Jun 9, 2008, at 4:48 PM, David Kelly wrote:
> On Mon, Jun 09, 2008 at 05:03:35AM -0400,
n...@gmail.com wrote:
> >
> > Hi all. I am working with ATMEGA169 microcontroller. I am using a
> > battery to provide supply to the board.I am uisng ISL6292 battery
> > charger. A TEMP pin of the charger monitors the battery
> temperature to
> > ensure a safe charging temperature range. This TEMP pin is connected
> > to ATMEGA. Some voltage is appearing on this pin from this voltage
> how
> > to calculate the temperature.
>
> Read the data sheet for starters:
> http://www.intersil.com/data/fn/fn9105.pdf
>
> The TEMP pin is not to be connected to the AVR but to an NTC resistor
> mounted on your battery. If you want to measure temperature I strongly
> suggest you stay off this signal and put your own NTC where ever, or
> use
> a purpose-designed factory calibrated temperature module/chip.
>
> --
> David Kelly N4HHE, d...@HiWAAY.net
> > > =====================================================================>
Whom computers would destroy, they must first drive mad.
On Mon, Jun 09, 2008 at 05:03:35AM -0400, n...@gmail.com wrote: >
> Hi all. I am working with ATMEGA169 microcontroller. I am using a
> battery to provide supply to the board.I am uisng ISL6292 battery
> charger. A TEMP pin of the charger monitors the battery temperature to
> ensure a safe charging temperature range. This TEMP pin is connected
> to ATMEGA. Some voltage is appearing on this pin from this voltage how
> to calculate the temperature.
The TEMP pin is not to be connected to the AVR but to an NTC resistor
mounted on your battery. If you want to measure temperature I strongly
suggest you stay off this signal and put your own NTC where ever, or use
a purpose-designed factory calibrated temperature module/chip.
--
David Kelly N4HHE, d...@HiWAAY.net
=======================================================================Whom
computers would destroy, they must first drive mad.
Reply by Zack Widup●June 9, 20082008-06-09
I don't quite understand the setup. What actually measures the
temperature? Does the ISL6292 have a temperature measuring device built
in that outputs a voltage on the TEMP pin? If that's the case, you just
need to set up one of the A/D converters and use it to measure the
voltage coming out of the 6292.
The data should all be in the data sheets for the respective parts.
Zack
On Mon, 9 Jun 2008, n...@gmail.com wrote:
>
> Hi all. I am working with ATMEGA169 microcontroller. I am using a
> battery to provide supply to the board.I am uisng ISL6292 battery
> charger. A TEMP pin of the charger monitors the battery temperature to
> ensure a safe charging temperature range. This TEMP pin is connected to
> ATMEGA. Some voltage is appearing on this pin from this voltage how to
> calculate the temperature.
>
Reply by n.na...@gmail.com●June 9, 20082008-06-09
Hi all. I am working with ATMEGA169 microcontroller. I am using a battery to
provide supply to the board.I am uisng ISL6292 battery charger. A TEMP pin of
the charger monitors the battery temperature to ensure a safe charging
temperature range. This TEMP pin is connected to ATMEGA. Some voltage is
appearing on this pin from this voltage how to calculate the temperature.