On Fri, 27 May 2005 16:31:59 +0200, Martin Maurer wrote:
>> [quoted text muted]
>
> STR7, e.g. STR711FR2T6 or STR710FZ2T6 (but never used them myself, so can't
> tell you how good they are running, or easy to use...)
>
We used ST7263 for an I/O board. ST was somewhat of a PITA in
terms of getting them (especially in DIP), but the parts were
inexpensive and worked pretty well.
Reply by Spehro Pefhany●May 30, 20052005-05-30
On 30 May 2005 16:35:16 -0700, the renowned "eKIK" <trash@boreios.net>
wrote:
>As googler said, Microchip has a line of PICs supporting USB.
>
>The 16C745 is REALLY cheap ($2.80), supports USB, firmware already
>written in both assembly and C.
>
>The downside is there's no 16X745 with flash memory, either they're OTP
>or UV-erasable. The name of the UV-erasable one in 16C745/JW I beleive.
>
>I'm afraid I have no experience with them myself...I just ordered a few
>but from reading the docs they seem really nice!
>
>Good luck in your search
>// eKIK
One difference between that part and the PIC18F2455 is that the
18F2455 supports full speed 12Mb/s USB2.0 and the 16C745 supports only
low speed USB1.1.
Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Reply by eKIK●May 30, 20052005-05-30
As googler said, Microchip has a line of PICs supporting USB.
The 16C745 is REALLY cheap ($2.80), supports USB, firmware already
written in both assembly and C.
The downside is there's no 16X745 with flash memory, either they're OTP
or UV-erasable. The name of the UV-erasable one in 16C745/JW I beleive.
I'm afraid I have no experience with them myself...I just ordered a few
but from reading the docs they seem really nice!
Good luck in your search
// eKIK
Reply by Ulf Samuelsson●May 30, 20052005-05-30
"Hw" <localhost@com.com> skrev i meddelandet
news:ZxEle.46898$887.4597@tornado.socal.rr.com...
> Any suggestions on uCs that have USB interfaces? Trying to avoid 8051
> cores.
>
> Atmel seem to make some AVRs with USB, anyone have experience with them?
>
> Regards
> H.
There are AVRs with USB in the AT43 series.
This is only useful for larger volume projects due to restrictions.
The AT76C713 on the other hand can be bought through distribution.
Runs at 48 MHz so it is quite fast (40 MIPS +) but
is more complex to handle than the average AVR because you have to do ISP
before you start debugging.
It can do some amazing things at that speed.
The AT91SAM7S64 is a very good general purpose chip and you get
going for about $300.
This includes dev kit, JTAG Emulator and IAR C compiler limited to 32 kB C
code (+ 32 kB Assembler code).
--
Best Regards,
Ulf Samuelsson
This is intended to be my personal opinion which may,
or may bot be shared by my employer Atmel Nordic AB
Reply by Richard●May 27, 20052005-05-27
"Hw" <localhost@com.com> wrote in message
news:ZxEle.46898$887.4597@tornado.socal.rr.com...
> Any suggestions on uCs that have USB interfaces? Trying to avoid 8051
> cores.
>
> Atmel seem to make some AVRs with USB, anyone have experience with them?
No experience with USB on an AVR but I have had success with USB on Atmel
AT91SAM7S devices - low pin count ARM7TDMI. No complaints or problems.
Regards,
Richard.
http://www.FreeRTOS.org
Reply by Martin Maurer●May 27, 20052005-05-27
> Atmel seem to make some AVRs with USB, anyone have experience with them?
STR7, e.g. STR711FR2T6 or STR710FZ2T6 (but never used them myself, so can't
tell you how good they are running, or easy to use...)
Regards,
Martin
Reply by googler●May 27, 20052005-05-27
PIC18F2455
Hw wrote:
> Any suggestions on uCs that have USB interfaces? Trying to avoid 8051
> cores.
>
> Atmel seem to make some AVRs with USB, anyone have experience with them?
>
> Regards
> H.
Reply by Hw●May 27, 20052005-05-27
Any suggestions on uCs that have USB interfaces? Trying to avoid 8051
cores.
Atmel seem to make some AVRs with USB, anyone have experience with them?
Regards
H.