>If you set the boot jumper on the EK to "INT" You can download code using
>Hyperterminal/X-modem.
>-- 
>A. P. Richelieu
>

Thanks very much.

I found a way already. Two ways actually. My jumper is set on EXT, and 
use the Uboot provided by atmel. It allows me to program by either th
serial cable (with the loadb command and kermit protocol fro
hyperterminal) or the ethernet cable (with tftp), which is faster.

BTW, I use the "comp.arch.embedded web interface" to post here but 
understand it is a "mail-based newsgroup". how can I subscribe ? searche
for comp.arch.embedded in yahoo groups. didn't find. and none of th
groups at the "discussion groups" link seems to correspond to this one.

thx
J�r�me

		
This message was sent using the comp.arch.embedded web interface o
www.EmbeddedRelated.com

>>
>
> Hi. I am facing the same issues.
> The files on the atmel site are designed for programming the flash through
> a hardware device such as MultiIce or Slingshot. Is there a way to do it
> directly through the serial cable ?
> Zanxy, did you find proper makefiles to use with GCC ? The samples on
> atmel website include project files for proprietary softwares but no
> makefile.

If you set the boot jumper on the EK to "INT" You can download code using
Hyperterminal/X-modem.


> Thanks
> J�r�me
>
>



-- 
A. P. Richelieu

>In news:d8c5sa$mp9$1@nemesis.news.tpi.pl,
>zanxy@zanxy.com <zanxy@zanxy.com> typed:
>
>> Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit.
>> I have gnu toolchain with gcc "3.4.3". I plan that we will run
>> programs directly on that processor - without any kind of operating
>> systems (linux or winCE).
>> I'm looking for project samples for this board. Are there in the
>> internet available any project free samples? I need informations
>> about memory addressing - where in memory can be placed a programm,
>> and how could I inform toolchain where I want to place executable
>> code (which options should I use).
>
>Check out http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3193
>
>Karl Olsen
>

Hi. I am facing the same issues.
The files on the atmel site are designed for programming the flash throug
a hardware device such as MultiIce or Slingshot. Is there a way to do i
directly through the serial cable ?
Zanxy, did you find proper makefiles to use with GCC ? The samples o
atmel website include project files for proprietary softwares but n
makefile.

Thanks
J&#4294967295;r&#4294967295;me



		
This message was sent using the comp.arch.embedded web interface o
www.EmbeddedRelated.com

Karl Olsen <kro@nospam.post3.tele.dk> wrote:
> In news:d8c5sa$mp9$1@nemesis.news.tpi.pl,
> zanxy@zanxy.com <zanxy@zanxy.com> typed:
> 
>> Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit.
>> I have gnu toolchain with gcc "3.4.3". I plan that we will run
>> programs directly on that processor - without any kind of operating
>> systems (linux or winCE).
>> I'm looking for project samples for this board. Are there in the
>> internet available any project free samples? I need informations
>> about memory addressing - where in memory can be placed a programm,
>> and how could I inform toolchain where I want to place executable
>> code (which options should I use).
> 
> Check out http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3193
> 
> Karl Olsen
> 

Ok, thanks.

zanxy

Hi

Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit.
I have gnu toolchain with gcc "3.4.3". I plan that we will run programs 
directly on that processor - without any kind of operating systems (linux 
or winCE).
I'm looking for project samples for this board. Are there in the internet 
available any project free samples? I need informations about memory 
addressing - where in memory can be placed a programm, and how could I 
inform toolchain where I want to place executable code (which options 
should I use). 

Sorry for my english.


zanxy

Hi

Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit.
I have gnu toolchain with gcc "3.4.3". I plan that we will run programs 
directly on that processor - without any kind of operating systems (linux 
or winCE).
I'm looking for project samples for this board. Are there in the internet 
available any project free samples? I need informations about memory 
addressing - where in memory can be placed a programm, and how could I 
inform toolchain where I want to place executable code (which options 
should I use). 

Sorry for my english.


zanxy