Driving ssd1338 via an 8 bit enabled-bus
Nothing I do brings it to life :-)
( I have a bin file without the source, that validates the screen
hardware actually runs...and it does )
I'm stumped
Does anyone have a driver for LCD ssd1338, or even a hint at what I
am doing wrong ?
Please :-)
---------------------------------
Driver posted below which might be of 'some' use to anyone fighting
the same problems with ssd1338 LCD
---------------------------------
void comm_out(unsigned char data)
{
unsigned int status = (LCDSTAT >> 5) & 0x1F;
while (status >= 0x0E)
status = (LCDSTAT >> 5) & 0x1F;
LCDIBYTE = data;
}
void data_out(unsigned char data)
{
unsigned int status = (LCDSTAT >> 5) & 0x1F;
while (status >= 0x0E)
status = (LCDSTAT >> 5) & 0x1F;
LCDDBYTE = data;
}
void data_out16( unsigned short data )
{
data_out( data & 0xFF );
data_out( data >> 8 );
}
// to achive clock = base * n / m, take MSUB = -n (two's complement)
and MADD = m - n
// so to have 6Mhz, we need n = 0x10 and m = 0xA0
#define LCD_MSUB 0xF0 // -n
#define LCD_MADD 0x90 // m - n
void lcdInit( void )
{
unsigned int s0 = LCDPSR0;
unsigned int s1 = LCDPSR1;
comm_out( 0x00C7 ); // Master current control
data_out( 0x0007 ); // 0x05 for Low brightness
// 0x07 for Normal brightness
// 0x0A for high brightness
// 0x01 for standby
comm_out(0x00C1); // Set contrast level for R , G ,B
data_out(0x0068); // Red contrast set
data_out(0x0058); // Green contrast set
data_out(0x009F); // Blue contrast set
comm_out(0x00B1); // Phase adjust
data_out(0x0022); //
comm_out(0x00B3); // Set frame rate
data_out(0x0010); // 0x10H for 85Hz
comm_out(0x00BB); // Set Pre-charge level for R , G , B
data_out(0x0000); // Red
data_out(0x0000); // Green
data_out(0x0000); // Blue
comm_out(0x00A6); // Inverse display mode off
comm_out(0x00D1); // Normal display
data_out(0x0002); //
comm_out(0x00AF); // Display on
}
Reply by Dezheng Tang●April 22, 20082008-04-22
If you use the the NOHAU board, I remember that there is
a CD coming with the board. Inside, BlinkyLCD project
has the basic LCD driver.
Tom
--- In l..., Jan Vanek wrote: >
> Hi Forum,
>
> I am using CrossWorks, LPC2888 and Nohau LPC2800 board
> with SSD1338 LCD
> (128x128). I tried to setup the clock for the LCD and
> then send the
> LCD-specific commands to initialize it, and then fill
> it with red, but the
> LCD remains black, or not turned on.
>
> After the lcd_init() I write red color using the
> data_out() in a cycle
> (128x128times). This cycle finishes, so the LCD is
> somehow processing the
> data, because otherwise the LCD FIFO (which I test
> using this LCDSTAT) would
> be full and the data_out() would never return.
>
> Regarding the LCD specific commands - I took them from
> Application Note to
> that specific SSD1228, so I thought it should be OK.
>
> Anybody has an idea what am I missing here? Or anybody
> has sample LCD
> initialization code for LPC288x, for whatever type of
> LCD?
>
> Thanks and regards,
> Jan Vanek
> #define LCD_MSUB 0x10
> #define LCD_MADD 0x70
>
> void lcd_init()
> {
> SYSFDCR1 &= ~SYSFDCR1_FDRUN;
> SYSFDCR1 = (LCD_MSUB << SYSFDCR1_MSUB_BIT) |
> (LCD_MADD <<
> SYSFDCR1_MADD_BIT) | SYSFDCR0_FDSTRCH |
> SYSFDCR0_FDRES;
> SYSFDCR1 &= ~SYSFDCR0_FDRES;
> SYSFDCR1 |= SYSFDCR1_FDRUN;
> LCDESR1 = LCDESR1_ESR_EN | (1 <<
> LCDESR1_ESR_SEL_BIT);
> LCDESR0 = 0;
>
> comm_out(0xAE); // Display off
> // more LCD commands
> comm_out(0xAF); // Display on
> }
>
> void comm_out(unsigned char data)
> {
> unsigned int status = (LCDSTAT >> 5) & 0x1F;
> while (status >= 0x0E)
> status = (LCDSTAT >> 5) & 0x1F;
> LCDIBYTE = data;
> }
>
> void data_out(unsigned char data)
> {
> unsigned int status = (LCDSTAT >> 5) & 0x1F;
> while (status >= 0x0E)
> status = (LCDSTAT >> 5) & 0x1F;
> LCDDBYTE = data;
> }
>
> ____________________________________________________________________________________ > Be a better friend, newshound, and
> know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ >
Reply by Jan Vanek●April 22, 20082008-04-22
Hi Forum,
I am using CrossWorks, LPC2888 and Nohau LPC2800 board
with SSD1338 LCD
(128x128). I tried to setup the clock for the LCD and
then send the
LCD-specific commands to initialize it, and then fill
it with red, but the
LCD remains black, or not turned on.
After the lcd_init() I write red color using the
data_out() in a cycle
(128x128times). This cycle finishes, so the LCD is
somehow processing the
data, because otherwise the LCD FIFO (which I test
using this LCDSTAT) would
be full and the data_out() would never return.
Regarding the LCD specific commands - I took them from
Application Note to
that specific SSD1228, so I thought it should be OK.
Anybody has an idea what am I missing here? Or anybody
has sample LCD
initialization code for LPC288x, for whatever type of
LCD?
