No problem, Jamie
Start a New Thread

Sorry for my misunderstanding.

Thanks,

Jamie

Software Factory, LLC
Sales 800-539-1780
Support 706-632-3763
Fax 706-632-6498
www.installfactory.com

On May 28, 2006, at 7:25 PM, Ing. Luis A. Briones wrote:

> The 404 is in the RCM2210 web config page, no to an internet
> address. I use
> this to set my rabbit.
>
> Luis
>
> ----- Original Message -----
> From: "Jamie Lay"
> To:
> Sent: Sunday, May 28, 2006 8:14 PM
> Subject: Re: [rabbit-semi] Out of memory?
> 404 means "not found". Are you contacting a web site for the page?
> If so, check your URL. It may be incorrect.
>
> Thanks,
>
> Jamie
>
> Software Factory, LLC
> Sales 800-539-1780
> Support 706-632-3763
> Fax 706-632-6498
> www.installfactory.com
> On May 28, 2006, at 7:11 PM, Ing. Luis A. Briones wrote:
>
>> Hi,
>>
>> I make a large program in a RCM2210 (256 K flash, 128 K ram). The
>> program worked well. I add a new module. I tested the new module
>> alone and work ok. But when I put the new module in the program I
>> have some bad operation. The program has a web configuration. This
>> part sends me a 404 error message or they put very slowly. I upload
>> a text archive to FTP and this doesnt work. I suppose that its a
>> problem memory. To many things for this RCM. This is my first work
>> with rabbit.
>>
>> Its possible that the memory be the problem?
>>
>> Best regards,
>>
>> Luis
>> SPONSORED LINKS
>> Embedded moduleMicrocontrollersZ-world
>> Intel microprocessors
Start a New Thread

The 404 is in the RCM2210 web config page, no to an internet address. I use
this to set my rabbit.

Luis

----- Original Message -----
From: "Jamie Lay"
To:
Sent: Sunday, May 28, 2006 8:14 PM
Subject: Re: [rabbit-semi] Out of memory?
404 means "not found". Are you contacting a web site for the page?
If so, check your URL. It may be incorrect.

Thanks,

Jamie

Software Factory, LLC
Sales 800-539-1780
Support 706-632-3763
Fax 706-632-6498
www.installfactory.com

On May 28, 2006, at 7:11 PM, Ing. Luis A. Briones wrote:

> Hi,
>
> I make a large program in a RCM2210 (256 K flash, 128 K ram). The
> program worked well. I add a new module. I tested the new module
> alone and work ok. But when I put the new module in the program I
> have some bad operation. The program has a web configuration. This
> part sends me a 404 error message or they put very slowly. I upload
> a text archive to FTP and this doesnt work. I suppose that its a
> problem memory. To many things for this RCM. This is my first work
> with rabbit.
>
> Its possible that the memory be the problem?
>
> Best regards,
>
> Luis
> SPONSORED LINKS
> Embedded moduleMicrocontrollersZ-world
> Intel microprocessors Start a New Thread

404 means "not found". Are you contacting a web site for the page?
If so, check your URL. It may be incorrect.

Thanks,

Jamie

Software Factory, LLC
Sales 800-539-1780
Support 706-632-3763
Fax 706-632-6498
www.installfactory.com

On May 28, 2006, at 7:11 PM, Ing. Luis A. Briones wrote:

> Hi,
>
> I make a large program in a RCM2210 (256 K flash, 128 K ram). The
> program worked well. I add a new module. I tested the new module
> alone and work ok. But when I put the new module in the program I
> have some bad operation. The program has a web configuration. This
> part sends me a 404 error message or they put very slowly. I upload
> a text archive to FTP and this doesnt work. I suppose that its a
> problem memory. To many things for this RCM. This is my first work
> with rabbit.
>
> Its possible that the memory be the problem?
>
> Best regards,
>
> Luis
> SPONSORED LINKS
> Embedded moduleMicrocontrollersZ-world
> Intel microprocessors
Start a New Thread

Hi,

I make a large program in a RCM2210 (256 K flash, 128 K ram). The program worked well. I add a new module. I tested the new module alone and work ok. But when I put the new module in the program I have some bad operation. The program has a web configuration. This part sends me a 404 error message or they put very slowly. I upload a text archive to FTP and this doesn't work. I suppose that it's a problem memory. To many things for this RCM. This is my first work with rabbit.

It's possible that the memory be the problem?

Best regards,

Luis Start a New Thread