On Fri, 26 Aug 2005 12:34:46 -0400, Spehro Pefhany
<speffSNIP@interlogDOTyou.knowwhat> wrote:
>On Fri, 26 Aug 2005 16:56:16 +0200, the renowned Anton Erasmus
><nobody@spam.prevent.net> wrote:
>
>>On Thu, 25 Aug 2005 17:52:59 -0400, Chris <chrispol@videotron.ca>
>>wrote:
>>
>>>What do you guys do when you have to drive quite a few leds? ie 4
>>>segented led displays and 20 standalone? 8 bit shift registers?
>>
>>Look at Maxim. They have quote a few new devices designed to drive
>>LEDs in low power systems. Each LED's current can be programmed in
>>16 steps. One also do not need a resitor in series with the LED, so
>>save quite a lot of power that way. Something like the MAX6957, which
>>are available from Digikey.
>>
>>Regards
>> Anton Erasmus
>
>How does dissipating the wasted power in the driver chip rather than
>resistors "save quite a lot of power"?
You are correct, I was not thinking. One would need some sort of
switch mode current control to improve the efficiency.
Regards
Anton Erasmus
Reply by Spehro Pefhany●August 26, 20052005-08-26
On Fri, 26 Aug 2005 16:56:16 +0200, the renowned Anton Erasmus
<nobody@spam.prevent.net> wrote:
>On Thu, 25 Aug 2005 17:52:59 -0400, Chris <chrispol@videotron.ca>
>wrote:
>
>>What do you guys do when you have to drive quite a few leds? ie 4
>>segented led displays and 20 standalone? 8 bit shift registers?
>
>Look at Maxim. They have quote a few new devices designed to drive
>LEDs in low power systems. Each LED's current can be programmed in
>16 steps. One also do not need a resitor in series with the LED, so
>save quite a lot of power that way. Something like the MAX6957, which
>are available from Digikey.
>
>Regards
> Anton Erasmus
How does dissipating the wasted power in the driver chip rather than
resistors "save quite a lot of power"?
Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Reply by Anton Erasmus●August 26, 20052005-08-26
On Thu, 25 Aug 2005 17:52:59 -0400, Chris <chrispol@videotron.ca>
wrote:
>What do you guys do when you have to drive quite a few leds? ie 4
>segented led displays and 20 standalone? 8 bit shift registers?
Look at Maxim. They have quote a few new devices designed to drive
LEDs in low power systems. Each LED's current can be programmed in
16 steps. One also do not need a resitor in series with the LED, so
save quite a lot of power that way. Something like the MAX6957, which
are available from Digikey.
Regards
Anton Erasmus
Reply by Capoccetta●August 26, 20052005-08-26
"Chris" <chrispol@videotron.ca> ha scritto nel messaggio
news:%4rPe.21576$hL3.76316@weber.videotron.net...
> What do you guys do when you have to drive quite a few leds? ie 4
> segented led displays and 20 standalone? 8 bit shift registers?
I normally use the M5450 from ST: serial data input, no external resistors!
--
Capoccetta
Reply by Ross Marchant●August 25, 20052005-08-25
"Chris" <chrispol@videotron.ca> wrote in message
news:%4rPe.21576$hL3.76316@weber.videotron.net...
> What do you guys do when you have to drive quite a few leds? ie 4
> segented led displays and 20 standalone? 8 bit shift registers?
Multiplexed or with a LED driver IC.
Interestingly, before the specific LED driver IC's we used a printer head
driver. It was just a big shift register with 24 high current sink outputs
and an output strobe we we used to control the brightness.
Ross
Reply by CBFalconer●August 25, 20052005-08-25
Chris wrote:
>
> What do you guys do when you have to drive quite a few leds? ie 4
> segented led displays and 20 standalone? 8 bit shift registers?
Multiplex.
--
Chuck F (cbfalconer@yahoo.com) (cbfalconer@worldnet.att.net)
Available for consulting/temporary embedded and systems.
<http://cbfalconer.home.att.net> USE worldnet address!
Reply by Spehro Pefhany●August 25, 20052005-08-25
On Thu, 25 Aug 2005 17:52:59 -0400, the renowned Chris
<chrispol@videotron.ca> wrote:
>What do you guys do when you have to drive quite a few leds? ie 4
>segented led displays and 20 standalone? 8 bit shift registers?
Multiplexed, in a very straightforward way, you can do that with 7 + 8
port pins (assuming a 7-segment internally multiplexed display with
decimal points and 20 discrete LEDs). For example, if you use a common
anode configuration you could have 7 source drivers and 8 sink
drivers. If you can live with an average current of 1mA for each 'on'
LED (say you have good LEDs), that's a maximum of 52mA total. Each
sink driver will have to be able to sink 7mA at about 100% duty cycle
and each source driver will have to be able to source 56mA with a 1:4
duty cycle.
In many cases, you can do that with a micro port plus one source
driver chip (or a few dual p-channel MOSFETs). Plus a couple quad
resistors.
If you want 15 or 20mA average per LED (either because you need
daylight visibility or because you want to buy Asian street-sweepings
for LEDs), you'll probably have to go with static drive and things get
a lot more complex. Using regular logic chips as LED drivers breaks
down above a certain current because of maximum per Vdd line or GND
line limits (read the data sheet carefully) and you have to go with
more parts again.
In between at perhaps 5mA per LED, you maybe can get away with HC
logic for some of the drivers, and can certainly use multiplexing.
Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Reply by Michael R. Kesti●August 25, 20052005-08-25
Chris wrote:
>What do you guys do when you have to drive quite a few leds? ie 4
>segented led displays and 20 standalone? 8 bit shift registers?
Maxim (Dallas Semiconductor) makes a line of LED controllers. I've
used the MAX7219 with success.
--
========================================================================
Michael Kesti | "And like, one and one don't make
| two, one and one make one."
mrkesti at comcast dot net | - The Who, Bargain
Reply by Mike Harrison●August 25, 20052005-08-25
On Thu, 25 Aug 2005 17:52:59 -0400, Chris <chrispol@videotron.ca> wrote:
>What do you guys do when you have to drive quite a few leds? ie 4
>segented led displays and 20 standalone? 8 bit shift registers?
shiftregs are a pretty good way. You don't need to use latched ones (595 etc.) as you can kill the
common drive while shifting new data in.
Reply by Chris●August 25, 20052005-08-25
What do you guys do when you have to drive quite a few leds? ie 4
segented led displays and 20 standalone? 8 bit shift registers?