Reply by tomi August 31, 20082008-08-31
>> Subject: Re: [lpc2000] CrossStudio and OpenOCD JTAG
>>
>> > Is it actually supported by CrossWorks? It isn't in the list of
>> > targets.
>> > It should work, you can add "Generic FTD2232" target interface in
>> > CrossStudio, but I can't configure it.
>>
>> Does it work with OpenOCD?
>>
>> .
>>
> "The Generic FT2232 device target interface provides access to ARM targets
> via target interfaces based on the FTDI Chip FT2232 dual USB UART/FIFO IC"
http://www.rowley.co.uk/documentation/arm_1_7/index.htm?http://www.rowley.co.uk/documentation/arm_1_7/arm_ft2232_target_interface.htm

Do you know that the interface actually works? That's why I asked if it
> works with OpenOCD.
>
I have still problem with this JTAG. JTAG works corecly, but with
CrossStudio can't connect. I see "Cannot identify target".

Channel A
ADBUS0 -> TCK;
ADBUS1 -> TDI;
ADBUS2 -> TDO;
ADBUS3 -> TMS;
ADBUS4 ->
ADBUS5 ->
ADBUS6 -> 1 if target present
ADBUS7 -> SRST in;

ACBUS0 -> TRST buffer enable;
ACBUS1 -> TRST;
ACBUS2 -> SRST buffer enable;
ACBUS3 -> SRST;
Channel B
BCBUS2 -> LED
BCBUS3 -> LED

My configuration is:

Output Pins 0x0F0F
Output Value 0x0000
nSRST Mask 0x0800 = ACBUS1 ?
nTRST Mask 0x0200 = ACBUS3 ?

All other are set to 0x0000.

What is wrong ?

How to set mask for led pins on channel B ?

An Engineer's Guide to the LPC2100 Series

Reply by Leon August 14, 20082008-08-14
----- Original Message -----
From: "tomi"
To:
Sent: Thursday, August 14, 2008 5:02 PM
Subject: Re: [lpc2000] CrossStudio and OpenOCD JTAG
> 2008/8/14 Leon > ----- Original Message -----
>> From: "tomi" >
>> To: >
>> Sent: Thursday, August 14, 2008 4:17 PM
>> Subject: Re: [lpc2000] CrossStudio and OpenOCD JTAG
>>
>> > Is it actually supported by CrossWorks? It isn't in the list of
>> > targets.
>> > It should work, you can add "Generic FTD2232" target interface in
>> > CrossStudio, but I can't configure it.
>>
>> Does it work with OpenOCD?
>>
>> .
>>
> "The Generic FT2232 device target interface provides access to ARM targets
> via target interfaces based on the FTDI Chip FT2232 dual USB UART/FIFO IC"
>
> http://www.rowley.co.uk/documentation/arm_1_7/arm_ft2232_target_interface.htm" target="_blank" rel="nofollow">http://www.rowley.co.uk/documentation/arm_1_7/index.htm?http://www.rowley.co.uk/documentation/arm_1_7/arm_ft2232_target_interface.htm

Do you know that the interface actually works? That's why I asked if it
works with OpenOCD.

Leon
Reply by tomi August 14, 20082008-08-14
2008/8/14 Leon

> ----- Original Message -----
> From: "tomi" >
> To: >
> Sent: Thursday, August 14, 2008 4:17 PM
> Subject: Re: [lpc2000] CrossStudio and OpenOCD JTAG
>
> > Is it actually supported by CrossWorks? It isn't in the list of targets.
> > It should work, you can add "Generic FTD2232" target interface in
> > CrossStudio, but I can't configure it.
>
> Does it work with OpenOCD?
>
> .
>
"The Generic FT2232 device target interface provides access to ARM targets
via target interfaces based on the FTDI Chip FT2232 dual USB UART/FIFO IC"

http://www.rowley.co.uk/documentation/arm_1_7/arm_ft2232_target_interface.htm" target="_blank" rel="nofollow">http://www.rowley.co.uk/documentation/arm_1_7/index.htm?http://www.rowley.co.uk/documentation/arm_1_7/arm_ft2232_target_interface.htm

Reply by Leon August 14, 20082008-08-14
----- Original Message -----
From: "tomi"
To:
Sent: Thursday, August 14, 2008 4:17 PM
Subject: Re: [lpc2000] CrossStudio and OpenOCD JTAG
> Is it actually supported by CrossWorks? It isn't in the list of targets.
> It should work, you can add "Generic FTD2232" target interface in
> CrossStudio, but I can't configure it.

Does it work with OpenOCD?

Leon
Reply by tomi August 14, 20082008-08-14
> I'm trying to use OpenOCD JTAG under CrossStudio but without efects.

Is it actually supported by CrossWorks? It isn't in the list of targets.
>

It should work, you can add "Generic FTD2232" target interface in
CrossStudio, but I can't configure it.

Reply by Leon August 14, 20082008-08-14
----- Original Message -----
From: "tomi"
To:
Sent: Thursday, August 14, 2008 2:45 PM
Subject: [lpc2000] CrossStudio and OpenOCD JTAG
> I'm trying to use OpenOCD JTAG under CrossStudio but without efects.

Is it actually supported by CrossWorks? It isn't in the list of targets.

Leon
Reply by tomi August 14, 20082008-08-14
I'm trying to use OpenOCD JTAG under CrossStudio but without efects.

This is OpenOCD JTAG project:
http://www.joernonline.de/dw/doku.php?id=projects:oocdlink:2_oocdlinks

Schematic: http://tinyurl.com/68qkag

ADBUS0 -> TCK;
ADBUS1 -> TDI;
ADBUS2 -> TDO;
ADBUS3 -> TMS;
ADBUS6 -> 1 if target present
ADBUS7 -> SRST in;

ACBUS0 -> TRST buffer enable;
ACBUS1 -> TRST;
ACBUS2 -> SRST buffer enable;
ACBUS3 -> SRST;

BCBUS2 -> LED
BCBUS3 -> LED

In CrossStudio "Generic FT2232 Device" I have

nSRST Inversion Mask 0x0200
nSRST Mask = 0x0200
nTRST Inversion Mask = 0x0000
nTRST Mask - 0x0400
Output Pins = 0x0F1B
Output Value = 0x0408
PID: 0xBAF8
VID: 0x15BA

Is this correct values ?