--- In l..., Herbert Demmel wrote: >
>
>
> Am 02.08.2010 23:23, schrieb bobtransformer:
> >
> > --- In l..., Herbert Demmel wrote:
> >> At 15:14 17.11.2008 +0000, you wrote:
> >>> FYI
> >>>
> >>> Revision 01.03 (30 January 2008) of the *preliminary* data sheet now
> >>> refers to RSTOUT as a 3.3V pin (corrected the 1.8V reference).
> >>>
> >>> RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC2478 being
> >>> in Reset state.
> >>>
> >> Does anybody know if the RSTOUT becomes active
> >> when the watchdog (or brown out) hits ?
> >>
> >> Regards
> >> Herbert
> >>
> >
> >
> > Now I am wanting to know the answer to this one... The manual
> > does not appear to say if the watchdog timer brings this line
> > low to reset the Phy peripheral.
> >
> > We just had a situation where this might need to be done in order for
> > the ethernet to come back up after a WD timeout.
> >
> > boB
> Bob,
>
> as far as I know unfortunately the answer is "no" ..
>
> Herbert
>
Thanks, Herbert...
Maybe what I can do instead is to just supply a reset to the ethernet reset line
using a GPIO line.... IF I have an extra one available.
Then, rest of the micro, either way, will reset the ethernet hardware when it
boots or when it re-boots due to a watchdog timeout.
Am 02.08.2010 23:23, schrieb bobtransformer: >
> --- In l..., Herbert Demmel wrote:
>> At 15:14 17.11.2008 +0000, you wrote:
>>> FYI
>>>
>>> Revision 01.03 (30 January 2008) of the *preliminary* data sheet now
>>> refers to RSTOUT as a 3.3V pin (corrected the 1.8V reference).
>>>
>>> RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC2478 being
>>> in Reset state.
>>>
>> Does anybody know if the RSTOUT becomes active
>> when the watchdog (or brown out) hits ?
>>
>> Regards
>> Herbert
>>
> Now I am wanting to know the answer to this one... The manual
> does not appear to say if the watchdog timer brings this line
> low to reset the Phy peripheral.
>
> We just had a situation where this might need to be done in order for
> the ethernet to come back up after a WD timeout.
>
> boB Bob,
as far as I know unfortunately the answer is "no" ..
Herbert
Reply by bobtransformer●August 2, 20102010-08-02
--- In l..., Herbert Demmel wrote: >
> At 15:14 17.11.2008 +0000, you wrote:
> >FYI
> >
> >Revision 01.03 (30 January 2008) of the *preliminary* data sheet now
> >refers to RSTOUT as a 3.3V pin (corrected the 1.8V reference).
> >
> >RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC2478 being
> >in Reset state.
> >
>
> Does anybody know if the RSTOUT becomes active
> when the watchdog (or brown out) hits ?
>
> Regards
> Herbert
>
Now I am wanting to know the answer to this one... The manual
does not appear to say if the watchdog timer brings this line
low to reset the Phy peripheral.
We just had a situation where this might need to be done in order for
the ethernet to come back up after a WD timeout.
boB
>
> >--- In l..., "rtstofer" wrote:
> > > You can test for yourself whether it is open drain. When the
> > > processor is not in reset, use a 1k pull-down resistor on the pin. It
> > > the output goes toward and nearly to 0V then it is open drain. If the
> > > pin voltage stays high, it is an active output.
> > >
> > > In the User Manual, NXP says this is a 3.3V pin. In the datasheet,
> > > they say it is a 1.8V pin. Hm... I guess you'll have to measure
it.
> > >
> > > Both schematics in both manuals show a pull-up resistor. Even if
> > > RSTOUT* is an active output, it is sometimes useful to be certain it
> > > pulls all the way to the rail before sending it to another chip.
> > >
> > > But if it works for Keil without a resistor, why not try it?
> > >
> > > Richard
> > >
> > > --- In l..., "carlochiesa78" wrote:
> > > >
> > > > *UP*
> > > >
> > > > No suggestions?
> > > >
> > > >
> > > > --- In l..., "carlochiesa78"
> >wrote:
> > > > >
> > > > > Hello all,
> > > > >
> > > > > I need more details on the \RSTOUT pin of the LPC2388.
> > > > >
> > > > > From the user manual:
> > > > > "RSTOUT � This is a 3.3 V pin. LOW on this pin indicates LPC23xx
> > > being
> > > > > in Reset state."
> > > > >
> > > > > Is this pin an open-drain or push-pull output?
> > > > > I have seen a 10k pull-up resistor in some reference design...
(i.e.
> > > > > LPC-2478STK and others)
> > > > > How does this pin work at power-up/down?
> > > > >
> > > > > My idea was to connect this \RSTOUT pin to the \RESET input pin
> >of the
> > > > > DP83848I in order to turn-off the transceiver if a reset event
> >occurs
> > > > > (also a software reset).
> > > > > Is this correct?
> > > > > Shouldn't I need a pull-down resistor on the \RSTOUT pin??
> > > > >
> > > > > In other eval. board like Keil MCB2300 the \RESET input pin of
> > > > > DP83848I is directly connected to the \RESET input pin of the
> >LPC23xx.
> > > > >
> > > > > Regards,
> > > > > Carlo
>
Reply by Herbert Demmel●November 17, 20082008-11-17
At 15:14 17.11.2008 +0000, you wrote: >FYI
>
>Revision 01.03 (30 January 2008) of the *preliminary* data sheet now
>refers to RSTOUT as a 3.3V pin (corrected the 1.8V reference).
>
>RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC2478 being
>in Reset state.
>
Does anybody know if the RSTOUT becomes active
when the watchdog (or brown out) hits ?
Regards
Herbert >--- In l..., "rtstofer" wrote:
> > You can test for yourself whether it is open drain. When the
> > processor is not in reset, use a 1k pull-down resistor on the pin. It
> > the output goes toward and nearly to 0V then it is open drain. If the
> > pin voltage stays high, it is an active output.
> >
> > In the User Manual, NXP says this is a 3.3V pin. In the datasheet,
> > they say it is a 1.8V pin. Hm... I guess you'll have to measure
it.
> >
> > Both schematics in both manuals show a pull-up resistor. Even if
> > RSTOUT* is an active output, it is sometimes useful to be certain it
> > pulls all the way to the rail before sending it to another chip.
> >
> > But if it works for Keil without a resistor, why not try it?
> >
> > Richard
> >
> > --- In l..., "carlochiesa78" wrote:
> > >
> > > *UP*
> > >
> > > No suggestions?
> > >
> > >
> > > --- In l..., "carlochiesa78"
>wrote:
> > > >
> > > > Hello all,
> > > >
> > > > I need more details on the \RSTOUT pin of the LPC2388.
> > > >
> > > > From the user manual:
> > > > "RSTOUT � This is a 3.3 V pin. LOW on this pin indicates LPC23xx
> > being
> > > > in Reset state."
> > > >
> > > > Is this pin an open-drain or push-pull output?
> > > > I have seen a 10k pull-up resistor in some reference design... (i.e.
> > > > LPC-2478STK and others)
> > > > How does this pin work at power-up/down?
> > > >
> > > > My idea was to connect this \RSTOUT pin to the \RESET input pin
>of the
> > > > DP83848I in order to turn-off the transceiver if a reset event
>occurs
> > > > (also a software reset).
> > > > Is this correct?
> > > > Shouldn't I need a pull-down resistor on the \RSTOUT pin??
> > > >
> > > > In other eval. board like Keil MCB2300 the \RESET input pin of
> > > > DP83848I is directly connected to the \RESET input pin of the
>LPC23xx.
> > > >
> > > > Regards,
> > > > Carlo
Reply by Chip Dyer●November 17, 20082008-11-17
FYI
Revision 01.03 (30 January 2008) of the *preliminary* data sheet now
refers to RSTOUT as a 3.3V pin (corrected the 1.8V reference).
RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC2478 being
in Reset state.
--- In l..., "rtstofer" wrote: > You can test for yourself whether it is open drain.
When the
> processor is not in reset, use a 1k pull-down resistor on the pin. It
> the output goes toward and nearly to 0V then it is open drain. If the
> pin voltage stays high, it is an active output.
>
> In the User Manual, NXP says this is a 3.3V pin. In the datasheet,
> they say it is a 1.8V pin. Hm... I guess you'll have to measure it.
>
> Both schematics in both manuals show a pull-up resistor. Even if
> RSTOUT* is an active output, it is sometimes useful to be certain it
> pulls all the way to the rail before sending it to another chip.
>
> But if it works for Keil without a resistor, why not try it?
>
> Richard
>
> --- In l..., "carlochiesa78" wrote:
> >
> > *UP*
> >
> > No suggestions?
> >
> >
> > --- In l..., "carlochiesa78" wrote: > > >
> > > Hello all,
> > >
> > > I need more details on the \RSTOUT pin of the LPC2388.
> > >
> > > From the user manual:
> > > "RSTOUT � This is a 3.3 V pin. LOW on this pin indicates LPC23xx
> being
> > > in Reset state."
> > >
> > > Is this pin an open-drain or push-pull output?
> > > I have seen a 10k pull-up resistor in some reference design... (i.e.
> > > LPC-2478STK and others)
> > > How does this pin work at power-up/down?
> > >
> > > My idea was to connect this \RSTOUT pin to the \RESET input pin of the > > > DP83848I in order to turn-off the transceiver if
a reset event occurs > > > (also a software reset).
> > > Is this correct?
> > > Shouldn't I need a pull-down resistor on the \RSTOUT pin??
> > >
> > > In other eval. board like Keil MCB2300 the \RESET input pin of
> > > DP83848I is directly connected to the \RESET input pin of the LPC23xx. > > >
> > > Regards,
> > > Carlo
Reply by rtstofer●November 1, 20082008-11-01
You can test for yourself whether it is open drain. When the
processor is not in reset, use a 1k pull-down resistor on the pin. It
the output goes toward and nearly to 0V then it is open drain. If the
pin voltage stays high, it is an active output.
In the User Manual, NXP says this is a 3.3V pin. In the datasheet,
they say it is a 1.8V pin. Hm... I guess you'll have to measure it.
Both schematics in both manuals show a pull-up resistor. Even if
RSTOUT* is an active output, it is sometimes useful to be certain it
pulls all the way to the rail before sending it to another chip.
But if it works for Keil without a resistor, why not try it?
Richard
--- In l..., "carlochiesa78" wrote: >
> *UP*
>
> No suggestions?
>
>
> --- In l..., "carlochiesa78" wrote:
> >
> > Hello all,
> >
> > I need more details on the \RSTOUT pin of the LPC2388.
> >
> > From the user manual:
> > "RSTOUT � This is a 3.3 V pin. LOW on this pin indicates LPC23xx being > > in Reset state."
> >
> > Is this pin an open-drain or push-pull output?
> > I have seen a 10k pull-up resistor in some reference design... (i.e.
> > LPC-2478STK and others)
> > How does this pin work at power-up/down?
> >
> > My idea was to connect this \RSTOUT pin to the \RESET input pin of the
> > DP83848I in order to turn-off the transceiver if a reset event occurs
> > (also a software reset).
> > Is this correct?
> > Shouldn't I need a pull-down resistor on the \RSTOUT pin??
> >
> > In other eval. board like Keil MCB2300 the \RESET input pin of
> > DP83848I is directly connected to the \RESET input pin of the LPC23xx.
> >
> >
> > Regards,
> > Carlo
>
Reply by carlochiesa78●November 1, 20082008-11-01
*UP*
No suggestions?
--- In l..., "carlochiesa78" wrote: >
> Hello all,
>
> I need more details on the \RSTOUT pin of the LPC2388.
>
> From the user manual:
> "RSTOUT � This is a 3.3 V pin. LOW on this pin indicates LPC23xx being
> in Reset state."
>
> Is this pin an open-drain or push-pull output?
> I have seen a 10k pull-up resistor in some reference design... (i.e.
> LPC-2478STK and others)
> How does this pin work at power-up/down?
>
> My idea was to connect this \RSTOUT pin to the \RESET input pin of the
> DP83848I in order to turn-off the transceiver if a reset event occurs
> (also a software reset).
> Is this correct?
> Shouldn't I need a pull-down resistor on the \RSTOUT pin??
>
> In other eval. board like Keil MCB2300 the \RESET input pin of
> DP83848I is directly connected to the \RESET input pin of the LPC23xx.
>
>
> Regards,
> Carlo
>
Reply by carlochiesa78●October 22, 20082008-10-22
Hello all,
I need more details on the \RSTOUT pin of the LPC2388.
>From the user manual: "RSTOUT This is a 3.3 V pin. LOW on this pin indicates LPC23xx being
in Reset state."
Is this pin an open-drain or push-pull output?
I have seen a 10k pull-up resistor in some reference design... (i.e.
LPC-2478STK and others)
How does this pin work at power-up/down?
My idea was to connect this \RSTOUT pin to the \RESET input pin of the
DP83848I in order to turn-off the transceiver if a reset event occurs
(also a software reset).
Is this correct?
Shouldn't I need a pull-down resistor on the \RSTOUT pin??
In other eval. board like Keil MCB2300 the \RESET input pin of
DP83848I is directly connected to the \RESET input pin of the LPC23xx.
Regards,
Carlo