> I can't get my Olimex arm-jtag to run with OCD commander either.
>
> I've tested just about every possible combination of bios
> setting, LPT port, communications delay, and target jumper
> configuration (Olimex LPC-P2106 and LPC-WEB). Swapped out
> the xtal on the '2106 board as a test too. Even tried a
> couple of older versions of OCD commander--no go.
>
> newell
Beware that you must reduce the OCD-speed when you connect the Olimex Board.
On my Hardware OCD Speed 5 works fine with my Olimex LPC Board
Thomas.
Reply by Thomas Motz●December 1, 20042004-12-01
> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
> Commander.
>
> Under Win2K it works fine. On my new PC under WinXP it fails.
> Commander gives the message "Adapter not connected"
> A parallel printer works fine on this LPT Port.
>
> Macraigor wrote that the Commander works with Win XP.
AAARGH!
Under Win2K I used OCD Commander Version V2.2.5 .
This Version works both under Win2K and WinXP.
Under WinXP I got the new Version 2.4.0 from OCD Commander
and this Version does n o t work with my WinXP.
Now I'm using V2.2.5 and it works fine on my new PC with WinXP.
Thomas
Reply by FLY135●November 30, 20042004-11-30
"Thomas Motz" <thomas.motz@gmx.net> wrote in message
news:co9ocv$ljb$1@ngspool-d02.news.aol.com...
> Hi all,
>
> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
> Commander.
>
> Under Win2K it works fine. On my new PC under WinXP it fails.
> Commander gives the message "Adapter not connected"
> A parallel printer works fine on this LPT Port.
>
> Macraigor wrote that the Commander works with Win XP.
> Has anybody used this combination? Do I need special drivers
> for LPT Port under WinXP?
Works fine on my XP Home. Try changing the speed parameter. I've used
Wiggler, Raven, and the Amontec. So far the Amontec seems to have the least
quirky operation.
Reply by Scott Newell●November 29, 20042004-11-29
Thomas Motz wrote:
>
> Hi all,
>
> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
> Commander.
>
> Under Win2K it works fine. On my new PC under WinXP it fails.
> Commander gives the message "Adapter not connected"
> A parallel printer works fine on this LPT Port.
>
> Macraigor wrote that the Commander works with Win XP.
> Has anybody used this combination? Do I need special drivers
> for LPT Port under WinXP?
I can't get my Olimex arm-jtag to run with OCD commander either.
I've tested just about every possible combination of bios
setting, LPT port, communications delay, and target jumper
configuration (Olimex LPC-P2106 and LPC-WEB). Swapped out
the xtal on the '2106 board as a test too. Even tried a
couple of older versions of OCD commander--no go.
I'm running under win2k, and the very same installation
of OCD commander works fine with BDM wigglers to my CPU32
hardware.
The Olimex arm-jtag clone did work for me under Rowley
Crossworks.
newell
Reply by slawc●November 28, 20042004-11-28
Thomas Motz wrote:
> "Leon Heller" <leon_heller@hotmail.com> schrieb im Newsbeitrag
> news:41a895e1$0$16590$cc9e4d1f@news-text.dial.pipex.com...
>
>>"Thomas Motz" <thomas.motz@gmx.net> wrote in message
>
>
>>No, I meant my own hardware I/F, which works like the Wiggler. The
>>Commander software works fine for me.
>>
>>What ARM hardware are you using?
>>
>>Leon
>
>
> I tested with several ARM Boards: AT91EB40a, Olimex LPC-P212X, Cirrus
> EP7312.
> With all these Boards I had no problems under Win2K, but this was on my old
> PC and
> I cast suspicion on the LPT Hardware now. (The commander works fine for you
> so in all
> probability I have a Hardware problem with my new PC. Onboard LPT Port from
> ASUS
> P4P800S-E)
>
> I will google for some Test Software for XP and Monday I will buy another
> LPT Hardware.
>
> Regards
> Thomas
>
>
I managed to damage onboard LPT on my system. Then we bought I/O LPT
card (PCI version) and we thought this will solve the problem. Printers
communicating with legacy drivers worked normaly but other software not.
Try before buy if you'll buy IO card.
BR,
Slawc
Reply by Tsvetan Usunov●November 28, 20042004-11-28
> I will google for some Test Software for XP and Monday I will buy another
> LPT Hardware.
>
we use XP and never have had whatsoever problem with our ARM-JTAG
check LPT port settings, and if your computer which run XP is faster
than other one where our JTAG "works" do some adjustments on SPEED
parameter
Best regards
Tsvetan
---
PCB prototypes for $26 at http://run.to/pcb
(http://www.olimex.com/pcb)
PCB any volume assembly (http://www.olimex.com/pcb/protoa.html)
Development boards for ARM, AVR, PIC, and MSP430
(http://www.olimex.com/dev)
Reply by Thomas Motz●November 27, 20042004-11-27
"Leon Heller" <leon_heller@hotmail.com> schrieb im Newsbeitrag
news:41a895e1$0$16590$cc9e4d1f@news-text.dial.pipex.com...
> "Thomas Motz" <thomas.motz@gmx.net> wrote in message
> No, I meant my own hardware I/F, which works like the Wiggler. The
> Commander software works fine for me.
>
> What ARM hardware are you using?
>
> Leon
I tested with several ARM Boards: AT91EB40a, Olimex LPC-P212X, Cirrus
EP7312.
With all these Boards I had no problems under Win2K, but this was on my old
PC and
I cast suspicion on the LPT Hardware now. (The commander works fine for you
so in all
probability I have a Hardware problem with my new PC. Onboard LPT Port from
ASUS
P4P800S-E)
I will google for some Test Software for XP and Monday I will buy another
LPT Hardware.
Regards
Thomas
Reply by Leon Heller●November 27, 20042004-11-27
"Thomas Motz" <thomas.motz@gmx.net> wrote in message
news:coa2tu$8j9$1@ngspool-d02.news.aol.com...
>
> "Leon Heller" <leon_heller@hotmail.com> schrieb im Newsbeitrag
> news:41a8691e$0$19159$cc9e4d1f@news-text.dial.pipex.com...
>> "Thomas Motz" <thomas.motz@gmx.net> wrote in message
>> news:co9ocv$ljb$1@ngspool-d02.news.aol.com...
>>> Hi all,
>>>
>>> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
>>> Commander.
>>>
>>> Under Win2K it works fine. On my new PC under WinXP it fails.
>
>> I use both a genuine Wiggler and my own design I/F without any problems
>> under WinXP. You must have the printer port set for 'EPP', that is the
>> most likely cause of your problem.
>>
>> Leon
>> --
> Dear Leon,
> thanks for your reply.
>
> A lot of reboots later I tested all possible configurations for the LPT
> Port.
> Unfortunateley the Fail-Message was constant.
>
> Your own I/F replaces the OCD Commander I think, so the Problem possibly
> depends on the Commander Software.
No, I meant my own hardware I/F, which works like the Wiggler. The Commander
software works fine for me.
What ARM hardware are you using?
Leon
Reply by Thomas Motz●November 27, 20042004-11-27
"Leon Heller" <leon_heller@hotmail.com> schrieb im Newsbeitrag
news:41a8691e$0$19159$cc9e4d1f@news-text.dial.pipex.com...
> "Thomas Motz" <thomas.motz@gmx.net> wrote in message
> news:co9ocv$ljb$1@ngspool-d02.news.aol.com...
>> Hi all,
>>
>> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
>> Commander.
>>
>> Under Win2K it works fine. On my new PC under WinXP it fails.
> I use both a genuine Wiggler and my own design I/F without any problems
> under WinXP. You must have the printer port set for 'EPP', that is the
> most likely cause of your problem.
>
> Leon
> --
Dear Leon,
thanks for your reply.
A lot of reboots later I tested all possible configurations for the LPT
Port.
Unfortunateley the Fail-Message was constant.
Your own I/F replaces the OCD Commander I think, so the Problem possibly
depends on the Commander Software.
Thomas
Reply by Leon Heller●November 27, 20042004-11-27
"Thomas Motz" <thomas.motz@gmx.net> wrote in message
news:co9ocv$ljb$1@ngspool-d02.news.aol.com...
> Hi all,
>
> I tried to use the Wiggler compatible JTAG Adapter from Olimex with OCD
> Commander.
>
> Under Win2K it works fine. On my new PC under WinXP it fails.
> Commander gives the message "Adapter not connected"
> A parallel printer works fine on this LPT Port.
>
> Macraigor wrote that the Commander works with Win XP.
> Has anybody used this combination? Do I need special drivers
> for LPT Port under WinXP?