Reply by Not Really Me●November 24, 20042004-11-24
Laurent Gauch wrote:
> Not Really Me wrote:
>
>> We have an Atmel EB55 board (ARM7TDMI in AT91M55800A chip) and the
>> AT91 expansion memory card. When have debugged projects on it using
>> an Abatron BDI2000 successfully, but now have to (customer
>> requirement) use a Multi-ice.
>>
>> The multi-ice works fine with the EB55 board, but we can not
>> successfully download code to it if the memory board is plugged in.
AUGH!!!
If all else fails read the documentation - carefully...
The correct settings for the EB55 are E6 and E8 closed, E7 and E9 open with
the following
config.
# EB55 EBI_CSR0 base address for external MEMORY
writemem.l 0xffe00000 0x0800200D
# EB55 EBI_CSR1 base address for external RAM
writemem.l 0xffe00004 0x10002001
# EB55 EBI_CSR2 base address for external MEMORY
writemem.l 0xffe00008 0x030024B5 #20000000
# EB55 EBI_CSR3 base address for external MEMORY
writemem.l 0xffe0000c 0x040024B5 #30000000
# EB55 EBI_CSR4 base address for external MEMORY
writemem.l 0xffe00010 0x05002021 #40000000
# EB55 EBI_CSR5 base address for external MEMORY
writemem.l 0xffe00014 0x05102021 #50000000
# EB55 EBI_CSR6 base address for external MEMORY
writemem.l 0xffe00018 0x60000000
# EB55 EBI_CSR7 base address for external MEMORY
# writemem.l 0xffe0001c 0x70000000
# EB55 Remap Control Reg
# writemem.l 0xffe00020 0x00000001
# EB55 memory control register
writemem.l 0xffe00024 0x00000010
Reply by Laurent Gauch●November 23, 20042004-11-23
Not Really Me wrote:
> We have an Atmel EB55 board (ARM7TDMI in AT91M55800A chip) and the AT91
> expansion memory card. When have debugged projects on it using an Abatron
> BDI2000 successfully, but now have to (customer requirement) use a
> Multi-ice.
>
> The multi-ice works fine with the EB55 board, but we can not successfully
> download code to it if the memory board is plugged in. We have checked the
> setup again using the Abatron and the hardware all works fine with the same
> code set.. The multi-ice works fine without the extra memory. We have tried
> far too many jumper combinations without any success.
>
> BTW the toolset with multiice is Codewarrior for ARM. With the Abatron it
> is GNU.
>
> Anyone have a clue as to what kind of difference we are seeing with the
> multi-ice?
>
> Scott
>
>
Maybe try to disconnect the nTRST and nRESET signal and try what happen!
Just keep TDI TDO TMS TCK.
Then place again nRESET only and then nTRST.
Laurent
______________________
Low cost JTAG ARM DEBUG VALUE PACK
www.amontec.com
Reply by Not Really Me●November 23, 20042004-11-23
We have an Atmel EB55 board (ARM7TDMI in AT91M55800A chip) and the AT91
expansion memory card. When have debugged projects on it using an Abatron
BDI2000 successfully, but now have to (customer requirement) use a
Multi-ice.
The multi-ice works fine with the EB55 board, but we can not successfully
download code to it if the memory board is plugged in. We have checked the
setup again using the Abatron and the hardware all works fine with the same
code set.. The multi-ice works fine without the extra memory. We have tried
far too many jumper combinations without any success.
BTW the toolset with multiice is Codewarrior for ARM. With the Abatron it
is GNU.
Anyone have a clue as to what kind of difference we are seeing with the
multi-ice?
Scott