Reply by donhamilton2002●September 13, 20092009-09-13
--- In A..., "pattloch" wrote: >
> Hello,
> I already press BP4 and reset and BMS is open. And i didn't load any code
to the board. It didn't work.
>
> So what is wrong?
Hello,
I already press BP4 and reset and BMS is open. And i didn't load any code
to the board. It didn't work.
So what is wrong?
Thanks
--- In A..., Narasimha Rao wrote: >
> If any program exists in dataflash or external flash then samba cannot detect
the board unless the code is erased. I think there might be bms jumper which
should be removed while talking to samba. When program is downloaded assert bms
jumper to low to execute the program.
>
> Regards
> snr
>
> -----Original Message-----
> From: donhamilton2002
> Sent: Saturday, September 12, 2009 8:55 PM
> To: A...
> Subject: [AT91SAM] Re: AT91SAM9260 EK connection via USB
>
>
> --- In A..., "pattloch" wrote:
> >
> > Hello,
> > I have purchased a Atmel AT91SAM9260 EK. I used SAM-BA and tried to connect
the board to via USB. It didn't work. There is no autodectection and the
connection failed.
> >
> > Please help. I am a newbie in embedded world.
>
> Did you load any code into the AT91SAM9260 EK ??
>
> What did you expect ??
>
> If you did load code into the chip, what code did you compile and load ??
>
> don
>
> >
> > Thanks
> >
> > Regards
> >
> Messages in this topic (2)
>
> [The entire original message is not included]
>
Reply by Narasimha Rao●September 12, 20092009-09-12
If any program exists in dataflash or external flash then samba cannot detect
the board unless the code is erased. I think there might be bms jumper which
should be removed while talking to samba. When program is downloaded assert bms
jumper to low to execute the program.
Regards
snr
-----Original Message-----
From: donhamilton2002
Sent: Saturday, September 12, 2009 8:55 PM
To: A...
Subject: [AT91SAM] Re: AT91SAM9260 EK connection via USB
--- In A..., "pattloch" wrote:
>
> Hello,
> I have purchased a Atmel AT91SAM9260 EK. I used SAM-BA and tried to connect
the board to via USB. It didn't work. There is no autodectection and the
connection failed.
>
> Please help. I am a newbie in embedded world.
Did you load any code into the AT91SAM9260 EK ??
What did you expect ??
If you did load code into the chip, what code did you compile and load ??
don
>
> Thanks
>
> Regards
>
Messages in this topic (2)
[The entire original message is not included]
Reply by donhamilton2002●September 12, 20092009-09-12
--- In A..., "pattloch" wrote: >
> Hello,
> I have purchased a Atmel AT91SAM9260 EK. I used SAM-BA and tried to connect
the board to via USB. It didn't work. There is no autodectection and the
connection failed.
>
> Please help. I am a newbie in embedded world.
Did you load any code into the AT91SAM9260 EK ??
What did you expect ??
If you did load code into the chip, what code did you compile and load ??
don
>
> Thanks
>
> Regards
>
Reply by pattloch●September 11, 20092009-09-11
Hello,
I have purchased a Atmel AT91SAM9260 EK. I used SAM-BA and tried to connect the
board to via USB. It didn't work. There is no autodectection and the
connection failed.