Reply by "Mar...@gmail.com [msp430]"●May 12, 20142014-05-12
The launchpad / ezUSB / FET430 use the same or very similar software, so it
may work.
I know they all work with mspdebug and the old closed-source .so lib.
Regards,
Mark
On Mon, May 12, 2014 at 10:29 AM, Barry Baldwin b...@indyme.com[msp430]
wrote:
> Hi Rob,
>
> Arrgh! I didn’t read your original post thoroughly enough. My
> apologies. You need to use the MSP-FET430UIF adapter when using the
> Elprotonic software. I’m guessing it will not work with the
Launchpad.
>
> Regards,
>
> Barry
Reply by "'Ro...@dcsi.net.au [msp430]"●May 12, 20142014-05-12
Hi Barry
Not a problem Mate, Thank you for the information 8-)
Cheers,
Rob
From: m... [mailto:m...]
Sent: Tuesday, 13 May 2014 2:29 AM
To: m...
Subject: [msp430] Re: Hex file installer
Hi Rob,
Arrgh! I didn't read your original post thoroughly enough. My
apologies.
You need to use the MSP-FET430UIF adapter when using the Elprotonic
software. I'm guessing it will not work with the Launchpad.
Regards,
Barry
Reply by "Bar...@indyme.com [msp430]"●May 12, 20142014-05-12
Hi Rob,
Arrgh! I didn't read your original post thoroughly enough. My apologies.
You need to use the MSP-FET430UIF adapter when using the Elprotonic software.
I'm guessing it will not work with the Launchpad.
Regards,
Barry
Reply by "'Ro...@dcsi.net.au [msp430]"●May 11, 20142014-05-11
Cheers Everyone for all of your replies, Thank you 8-)
Barry, I had a look at Elprotonic’s software and from what I can gather it
uses JTAG or Spy By Wire to program the MSP430 MCU. Does the Launchpad ( with
the chip insatalled into it ) support JTAG/ Spy By Wire ( this one eludes me )
or could I just wire the launchpad via Spy By Wire to a breadboard with the chip
in it and program it this way ?
Thanks again and Cheers,
Rob.
From: m... [mailto:m...]
Sent: Saturday, 10 May 2014 1:36 AM
To: m...
Subject: Re: [msp430] Hex file installer
You could also download from Elprotronic their FETPRO-430 lite. It's free.
That's what I use when I need to program a hex file.
Cheers,
Barry
Reply by "bba...@indyme.com [msp430]"●May 9, 20142014-05-09
You could also download from Elprotronic their FETPRO-430 lite. It's free.
That's what I use when I need to program a hex file.
Cheers,
Barry
Reply by "han...@yahoo.com [msp430]"●May 9, 20142014-05-09
On Thu, 2014-05-08 at 18:13 -0700, r...@dcsi.net.au wrote: > Hello Group,
>
> I'm a long time listener and first time poster, pretty well up with
> the hardware side of MCU's but lack a fair bit of knowledge on the
> software side, hence my question today...
>
> Does the MSP430 Lauchpad have a hex file downloader ? ( not comparing
> the MSP430 to PIC or AVR but they have software that does just that )
> I've downloaded and looked CCS 5.5, IAR 5 and Energia and cant see
> where to " import " a hex file to download it into the MSP430.
On Linux, just grab "mspdebug" from Sourceforge (or straight from your
distro - "apt-get install mspdebug" or whatever.) Mspdebug may also be
available for Windows, Mac etc but I haven't tried them.
Works fine with my launchpad and ez430f2013 USB sticks.
Reply by robe...@dcsi.net.au●May 9, 20142014-05-09
Hello Group,
I'm a long time listener and first time poster, pretty well up with the
hardware side of MCU's but lack a fair bit of knowledge on the software
side, hence my question today...
Does the MSP430 Lauchpad have a hex file downloader ? ( not comparing the
MSP430 to PIC or AVR but they have software that does just that ) I've
downloaded and looked CCS 5.5, IAR 5 and Energia and cant see where to " import
" a hex file to download it into the MSP430.
If anyone has any thoughts or directions that would be appreciated,
Thanks everyone,
Cheers,
Rob.