----- Original Message -----
From: "Alexan_e"
To:
Sent: Wednesday, June 01, 2011 9:52 AM
Subject: Re: [lpc2000] ARMwizard v2.0 freeware applicaton to setup the mcu
registers (update), LPC2xxx & LPC17xx > 175x are almost the same as 176x, they just have
80pins instead of 100 so
> some pins have to be removed and then you have to set the available
> functions for each pin.
> Other sections have to be changed too , the direction and open drain
> I have started working on them yesterday (1751/52/54/56/58/59) and I have
> them almost ready, I will be able to post them later today.
It's great news. You are guru.
Thanks you a lot
Jarda
175x are almost the same as 176x, they just have 80pins instead of 100 so some
pins have to be removed and then you have to set the available functions for
each pin.
Other sections have to be changed too , the direction and open drain
I have started working on them yesterday (1751/52/54/56/58/59) and I have them
almost ready, I will be able to post them later today.
After that I would like to add the 177x, 178x but the problem with these is that
each one is made in two or three different sizes (different pin count) so it
will take some time to make different profiles for each chip and each case, they
also have a huge amount of pins.
I don't have a specific plan for the future mcu family support, for each
new family I have to read the datasheets to learn the operation and register
names and then incorporate the needed changes.
It is not very easy because I have only worked with LPC2103 so each different
mcu family adds new things, it takes a lot of time too.
Alex
On 06/01/2011 09:34 AM, Jaromir Subcik wrote:
> Great utility Alex,
> that is exactly what I had been searching for.
> The .ini files looks readable and it looks like there is easy possible to add
another LPC's (i.e.LPC175x) by editing [PINSEL] section in existing
LPC176x.ini file. (I'm working with LPC1754 now ;-) )
> Do you plan add also LPC13xx and LPC11xx (with different IO handling through
IOCON registers) in your project?
>
> Thank you for your job.
> Jarda
>
> ----- Original Message -----
> From: Alexan_e
> To: l...
> Sent: Tuesday, May 31, 2011 4:26 PM
> Subject: [lpc2000] ARMwizard v2.0 freeware applicaton to setup the mcu
registers (update), LPC2xxx& LPC17xx
> ARMwizard updated to version 2.0
>
> I'm happy to anounce that v2 supports the LPC17xx CortexM3 chips.
> The new version includes profiles for LPC1763, LPC1764, LPC1765, LPC1766,
LPC1767, LPC1768, LPC1769
>
> What is new
>
> . Added support for LPC17xx chips, includes LPC1763/64/65/66/67/68/69 mcu
profiles
> . Added pin setting for open drain and repeater mode for LPC17xx
> . Added GPIO interrupt trigger edge selector to enable interrupts for
selected GPIO pins
> . CLKDIV register of A/D can also be set by target sample rate ( in
addition to A/D frequency)
> . When Timer2& Timer3 is used the PCONP enable bit is set to enable the
timer operation
>
> You can download the new version from http://alexan.edaboard.eu
>
> Best regards
> Alex
Reply by Jaromir Subcik●June 1, 20112011-06-01
Great utility Alex,
that is exactly what I had been searching for.
The .ini files looks readable and it looks like there is easy possible to add
another LPC's (i.e.LPC175x) by editing [PINSEL] section in existing
LPC176x.ini file. (I'm working with LPC1754 now ;-) )
Do you plan add also LPC13xx and LPC11xx (with different IO handling through
IOCON registers) in your project?
Thank you for your job.
Jarda
----- Original Message -----
From: Alexan_e
To: l...
Sent: Tuesday, May 31, 2011 4:26 PM
Subject: [lpc2000] ARMwizard v2.0 freeware applicaton to setup the mcu
registers (update), LPC2xxx & LPC17xx
ARMwizard updated to version 2.0
I'm happy to anounce that v2 supports the LPC17xx CortexM3 chips.
The new version includes profiles for LPC1763, LPC1764, LPC1765, LPC1766,
LPC1767, LPC1768, LPC1769
What is new
. Added support for LPC17xx chips, includes LPC1763/64/65/66/67/68/69 mcu
profiles
. Added pin setting for open drain and repeater mode for LPC17xx
. Added GPIO interrupt trigger edge selector to enable interrupts for selected
GPIO pins
. CLKDIV register of A/D can also be set by target sample rate ( in addition
to A/D frequency)
. When Timer2 & Timer3 is used the PCONP enable bit is set to enable the timer
operation
________________________________
From: Alexan_e
To: l...
Sent: Tue, May 31, 2011 8:26:38 AM
Subject: [lpc2000] ARMwizard v2.0 freeware applicaton to setup the mcu registers
(update), LPC2xxx & LPC17xx
ARMwizard updated to version 2.0
I'm happy to anounce that v2 supports the LPC17xx CortexM3 chips.
The new version includes profiles for LPC1763, LPC1764, LPC1765, LPC1766,
LPC1767, LPC1768, LPC1769
What is new
• Added support for LPC17xx chips, includes LPC1763/64/65/66/67/68/69 mcu
profiles
• Added pin setting for open drain and repeater mode for LPC17xx
• Added GPIO interrupt trigger edge selector to enable interrupts for
selected
GPIO pins
• CLKDIV register of A/D can also be set by target sample rate ( in
addition to
A/D frequency)
• When Timer2 & Timer3 is used the PCONP enable bit is set to enable the
timer
operation
Thank you for following through on this Alex. I'll download it a little
later today and have a peek.
Larry
--- In l..., "Alexan_e" wrote: >
> ARMwizard updated to version 2.0
>
> I'm happy to anounce that v2 supports the LPC17xx CortexM3 chips.
> The new version includes profiles for LPC1763, LPC1764, LPC1765, LPC1766,
LPC1767, LPC1768, LPC1769
>
> What is new
>
> . Added support for LPC17xx chips, includes LPC1763/64/65/66/67/68/69 mcu
profiles
> . Added pin setting for open drain and repeater mode for LPC17xx
> . Added GPIO interrupt trigger edge selector to enable interrupts for selected
GPIO pins
> . CLKDIV register of A/D can also be set by target sample rate ( in addition
to A/D frequency)
> . When Timer2 & Timer3 is used the PCONP enable bit is set to enable the timer
operation
>
> You can download the new version from http://alexan.edaboard.eu
>
> Best regards
> Alex
>
Reply by Alexan_e●May 31, 20112011-05-31
ARMwizard updated to version 2.0
I'm happy to anounce that v2 supports the LPC17xx CortexM3 chips.
The new version includes profiles for LPC1763, LPC1764, LPC1765, LPC1766,
LPC1767, LPC1768, LPC1769
What is new
. Added support for LPC17xx chips, includes LPC1763/64/65/66/67/68/69 mcu
profiles
. Added pin setting for open drain and repeater mode for LPC17xx
. Added GPIO interrupt trigger edge selector to enable interrupts for selected
GPIO pins
. CLKDIV register of A/D can also be set by target sample rate ( in addition to
A/D frequency)
. When Timer2 & Timer3 is used the PCONP enable bit is set to enable the timer
operation