----- Original Message -----
From: "Bruce Paterson" <bruce@bruc...>
To: <lpc2000@lpc2...>
Sent: Friday, May 27, 2005 8:27 AM
Subject: Re: [lpc2000] Amontec Chameleon
> Leon Heller wrote:
> > course. Has anyone got the Chameleon to work with the Philips ARM
chips?
>
> Yep works fine in Raven mode with a lpc2124. Never tried Wiggler mode.
> There is a special Chameleon target for Philips LPCs in particular you
> must use, not the generic JTAG one that comes in the bundle. Grab off
> their website.
Leon Heller wrote: > course. Has anyone got the Chameleon to work with
the Philips ARM chips?
Yep works fine in Raven mode with a lpc2124. Never tried Wiggler mode.
There is a special Chameleon target for Philips LPCs in particular you
must use, not the generic JTAG one that comes in the bundle. Grab off
their website.
Lack of good h/w breakpoint support when used with ocdremote and Insight
still very annoying.
I'm using the latest ocdremote.
Bill Knight wrote:
> This SOUNDS like the error that newer versions of
OcdLibRemote return
> when they find a non-standard WIGGLER. I believe Macraigor's
products
> have a jumper between a couple of the parallel port pins that the
> newer versions of code are checking. I do not know if Amontec has
> added that functionality to the FPGA firmware. Others on the mailing
> list might be able to confirm either or both. If that is the problem,
> you could either acquire an older version of OcdLibRemote or build a
> db-25 adapter to add the jumper.
Agreed. I think I also managed to get it with a laptop that had a
Parallel port that didn't configure from BIOS properly into the right
mode. This was back when I was mucking about with a home made wiggler,
so it may not be relevant to the Chameleon.
Dear friends,
I buy ChameleonPOD from second hand. Configuration for Xilinx, Altera,
Lattice, Atmel, ARM work fine.
Now i wont program MSP430 and PSD chips from ST, but i dont know if it is
possible with ChameleonPOD.
In configuration SW i see "amt_chm_080_st_psd_flashlink" but pinout i
dont
know. And in any mailing list users
talk about configutation for MSP430.
Iam contact Amontec (Laurent Gauch) and receive this answer"
>>Yes, I can help you to use the Chameleon POD
for PSD and MSP430.
>>Actually, I am not in my office. I will send you a new email when I
will
>>be back to me office tommorrow.
and nothing more, Amontec stop all communications with me :-((
Can anybody help me?
Can anybody send me actual configurations and coresponding pinouts?
king regards
J.Masek
Reply by Arie de Muynck●May 26, 20052005-05-26
From: "Leon Heller" <leon.heller@leon...> > Same error (43) as with OCD Commander. I think
I'll admit defeat and give up > trying to get it to work.
Hi Leon,
If you really give up I'd like to buy it and give it a try.
I've got access to a logic analyzer, a real Raven and my own Perfect
Wiggler
;-) to compare against.
Regards,
Arie de Muynck
You can also reply to the temporary chameleon@cham...
Reply by Leon Heller●May 26, 20052005-05-26
----- Original Message -----
From: "soren_t_hansen" <soren_t_hansen@sore...>
To: <lpc2000@lpc2...>
Sent: Thursday, May 26, 2005 6:00 PM
Subject: [lpc2000] Re: Amontec Chameleon
[snip] > > >Same error (43) as with OCD Commander. I
think I'll admit defeat
> and give up
> > >trying to get it to work.
> >
> > This SOUNDS like the error that newer versions of OcdLibRemote
return
> > when they find a non-standard WIGGLER. I believe Macraigor's
products
> > have a jumper between a couple of the parallel port pins that the
> > newer versions of code are checking. I do not know if Amontec has
> > added that functionality to the FPGA firmware. Others on the
mailing
> > list might be able to confirm either or both. If that is the
problem,
> > you could either acquire an older version of OcdLibRemote or build
a
> > db-25 adapter to add the jumper.
> >
> > -Bill
>
> I've just bought 4 Chameleons, and are using them together with
> OCDRemote 2.12 and Eclipse vith the Zylin CDT plugin. This is working
> just fine, and I'm using the Chameleon as a Raven_All_Speeds and
> connects with speed = 4.
>
> Perhaps mine is faulty. It was OCDremote 2.12 I tried.
>
> Leon
How is your LPT1 set up? Mine is configured to EPP mode, but the other
day I ran on another machine that wasn't. You could try to see if that
did the trick.
[snip] > > >Same error (43) as with OCD Commander. I
think I'll admit defeat
> and give up
> > >trying to get it to work.
> >
> > This SOUNDS like the error that newer versions of OcdLibRemote
return
> > when they find a non-standard WIGGLER. I believe Macraigor's
products
> > have a jumper between a couple of the parallel port pins that the
> > newer versions of code are checking. I do not know if Amontec has
> > added that functionality to the FPGA firmware. Others on the
mailing
> > list might be able to confirm either or both. If that is the
problem,
> > you could either acquire an older version of OcdLibRemote or build
a
> > db-25 adapter to add the jumper.
> >
> > -Bill
>
> I've just bought 4 Chameleons, and are using them together with
> OCDRemote 2.12 and Eclipse vith the Zylin CDT plugin. This is working
> just fine, and I'm using the Chameleon as a Raven_All_Speeds and
> connects with speed = 4.
>
> Perhaps mine is faulty. It was OCDremote 2.12 I tried.
>
> Leon
How is your LPT1 set up? Mine is configured to EPP mode, but the other
day I ran on another machine that wasn't. You could try to see if that
did the trick.
/Sen
Reply by Leon Heller●May 26, 20052005-05-26
----- Original Message -----
From: "soren_t_hansen" <soren_t_hansen@sore...>
To: <lpc2000@lpc2...>
Sent: Thursday, May 26, 2005 5:36 PM
Subject: [lpc2000] Re: Amontec Chameleon
--- In lpc2000@lpc2..., "Bill Knight" <BillK@t...> wrote: > On Thu, 26 May 2005 15:56:37 +0100, Leon Heller
wrote:
>
> >http://webspace.webring.com/people/jl/leon_heller/
> >----- Original Message -----
> >From: "Leon Heller" <leon.heller@d...>
> >To: <lpc2000@lpc2...>
> >Sent: Thursday, May 26, 2005 3:46 PM
> >Subject: Re: [lpc2000] Amontec Chameleon
> >> ----- Original Message -----
> >> From: "Bill Knight" <BillK@t...>
> >> To: <lpc2000@lpc2...>
> >> Sent: Thursday, May 26, 2005 2:54 PM
> >> Subject: Re: [lpc2000] Amontec Chameleon
> >>
> >>
> >>> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
> >>>
> >>>>----- Original Message -----
> >>>>From: "Bill Knight" <BillK@t...>
> >>>>To: <lpc2000@lpc2...>
> >>>>Sent: Thursday, May 26, 2005 2:03 PM
> >>>>Subject: Re: [lpc2000] Amontec Chameleon
> >>>
> >>>
> >>>>> I've used it in both WIGGLER and Raven modes with
the LPC. I use an > >>>>> older version of OCBLibRemote
with the following command lines:
> >>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
> >>>>> or
> >>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
> >>>>> The 's' param may be a bit slow but is the
setting for the project on > >>>>> which I am currently working.
I typically use the RAVEN mode except > >>>>> when using CrossWorks which
only supports the WIGGLER mode (they may > >>>>> have
> >>>>> RAVEN mode now, not sure). Also, the code for the
Chameleon itsself > >>>>> has
> >>>>> not
> >>>>> been updated from their web site in some time.
> >>>
> >>>>I'm using OCD Commander. I've downloaded
OCDRemote for Windows and
> >>>>installed
> >>>>it, but can't run it and can't find the
executable.
> >>>
> >>> IIRC it is in Cygwin\usr\local\bin
> >>> I usually create a Windows link to it in my project
directory setting the > >>> parameters correctly, then just
double-click it when it is needed.
> >>
> >> Sorry, I found it where you said.
> >>
> >> I'll see how I get on with it.
>
> >Same error (43) as with OCD Commander. I think I'll admit
defeat and give up > >trying to get it to work.
>
> This SOUNDS like the error that newer versions of OcdLibRemote return
> when they find a non-standard WIGGLER. I believe Macraigor's
products
> have a jumper between a couple of the parallel port pins that the
> newer versions of code are checking. I do not know if Amontec has
> added that functionality to the FPGA firmware. Others on the mailing
> list might be able to confirm either or both. If that is the problem,
> you could either acquire an older version of OcdLibRemote or build a
> db-25 adapter to add the jumper.
>
> -Bill
I've just bought 4 Chameleons, and are using them together with
OCDRemote 2.12 and Eclipse vith the Zylin CDT plugin. This is working
just fine, and I'm using the Chameleon as a Raven_All_Speeds and
connects with speed = 4.
Perhaps mine is faulty. It was OCDremote 2.12 I tried.
Leon
Reply by soren_t_hansen●May 26, 20052005-05-26
--- In lpc2000@lpc2..., "Bill Knight" <BillK@t...> wrote: > On Thu, 26 May 2005 15:56:37 +0100, Leon Heller
wrote:
>
> >http://webspace.webring.com/people/jl/leon_heller/
> >----- Original Message -----
> >From: "Leon Heller" <leon.heller@d...>
> >To: <lpc2000@lpc2...>
> >Sent: Thursday, May 26, 2005 3:46 PM
> >Subject: Re: [lpc2000] Amontec Chameleon
> >> ----- Original Message -----
> >> From: "Bill Knight" <BillK@t...>
> >> To: <lpc2000@lpc2...>
> >> Sent: Thursday, May 26, 2005 2:54 PM
> >> Subject: Re: [lpc2000] Amontec Chameleon
> >>
> >>
> >>> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
> >>>
> >>>>----- Original Message -----
> >>>>From: "Bill Knight" <BillK@t...>
> >>>>To: <lpc2000@lpc2...>
> >>>>Sent: Thursday, May 26, 2005 2:03 PM
> >>>>Subject: Re: [lpc2000] Amontec Chameleon
> >>>
> >>>
> >>>>> I've used it in both WIGGLER and Raven modes with
the LPC. I use an > >>>>> older version of OCBLibRemote
with the following command lines:
> >>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
> >>>>> or
> >>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
> >>>>> The 's' param may be a bit slow but is the
setting for the project on > >>>>> which I am currently working.
I typically use the RAVEN mode except > >>>>> when using CrossWorks which
only supports the WIGGLER mode (they may > >>>>> have
> >>>>> RAVEN mode now, not sure). Also, the code for the
Chameleon itsself > >>>>> has
> >>>>> not
> >>>>> been updated from their web site in some time.
> >>>
> >>>>I'm using OCD Commander. I've downloaded
OCDRemote for Windows and
> >>>>installed
> >>>>it, but can't run it and can't find the
executable.
> >>>
> >>> IIRC it is in Cygwin\usr\local\bin
> >>> I usually create a Windows link to it in my project
directory setting the > >>> parameters correctly, then just
double-click it when it is needed.
> >>
> >> Sorry, I found it where you said.
> >>
> >> I'll see how I get on with it.
>
> >Same error (43) as with OCD Commander. I think I'll admit
defeat and give up > >trying to get it to work.
>
> This SOUNDS like the error that newer versions of OcdLibRemote return
> when they find a non-standard WIGGLER. I believe Macraigor's
products
> have a jumper between a couple of the parallel port pins that the
> newer versions of code are checking. I do not know if Amontec has
> added that functionality to the FPGA firmware. Others on the mailing
> list might be able to confirm either or both. If that is the problem,
> you could either acquire an older version of OcdLibRemote or build a
> db-25 adapter to add the jumper.
>
> -Bill
I've just bought 4 Chameleons, and are using them together with
OCDRemote 2.12 and Eclipse vith the Zylin CDT plugin. This is working
just fine, and I'm using the Chameleon as a Raven_All_Speeds and
connects with speed = 4.
/Sen
Reply by Leon Heller●May 26, 20052005-05-26
----- Original Message -----
From: "Bill Knight" <BillK@Bill...>
To: <lpc2000@lpc2...>
Sent: Thursday, May 26, 2005 5:03 PM
Subject: Re: [lpc2000] Amontec Chameleon
> On Thu, 26 May 2005 15:56:37 +0100, Leon Heller
wrote:
>
>>http://webspace.webring.com/people/jl/leon_heller/
>>----- Original Message -----
>>From: "Leon Heller" <leon.heller@leon...>
>>To: <lpc2000@lpc2...>
>>Sent: Thursday, May 26, 2005 3:46 PM
>>Subject: Re: [lpc2000] Amontec Chameleon
>>> ----- Original Message -----
>>> From: "Bill Knight" <BillK@Bill...>
>>> To: <lpc2000@lpc2...>
>>> Sent: Thursday, May 26, 2005 2:54 PM
>>> Subject: Re: [lpc2000] Amontec Chameleon
>>>
>>>
>>>> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
>>>>
>>>>>----- Original Message -----
>>>>>From: "Bill Knight" <BillK@Bill...>
>>>>>To: <lpc2000@lpc2...>
>>>>>Sent: Thursday, May 26, 2005 2:03 PM
>>>>>Subject: Re: [lpc2000] Amontec Chameleon
>>>>
>>>>
>>>>>> I've used it in both WIGGLER and Raven modes with
the LPC. I use an
>>>>>> older version of OCBLibRemote with the following
command lines:
>>>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
>>>>>> or
>>>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
>>>>>> The 's' param may be a bit slow but is the
setting for the project on
>>>>>> which I am currently working. I typically use the RAVEN
mode except
>>>>>> when using CrossWorks which only supports the WIGGLER
mode (they may
>>>>>> have
>>>>>> RAVEN mode now, not sure). Also, the code for the
Chameleon itsself
>>>>>> has
>>>>>> not
>>>>>> been updated from their web site in some time.
>>>>
>>>>>I'm using OCD Commander. I've downloaded OCDRemote
for Windows and
>>>>>installed
>>>>>it, but can't run it and can't find the
executable.
>>>>
>>>> IIRC it is in Cygwin\usr\local\bin
>>>> I usually create a Windows link to it in my project directory
setting
>>>> the
>>>> parameters correctly, then just double-click it when it is
needed.
>>>
>>> Sorry, I found it where you said.
>>>
>>> I'll see how I get on with it.
>
>>Same error (43) as with OCD Commander. I think I'll admit defeat
and give
>>up
>>trying to get it to work.
>
> This SOUNDS like the error that newer versions of OcdLibRemote return
> when they find a non-standard WIGGLER. I believe Macraigor's
products
> have a jumper between a couple of the parallel port pins that the
> newer versions of code are checking. I do not know if Amontec has
> added that functionality to the FPGA firmware. Others on the mailing
> list might be able to confirm either or both. If that is the problem,
> you could either acquire an older version of OcdLibRemote or build a
> db-25 adapter to add the jumper.
The link beween pins 8 and 15? That might be the cause of the problem. I'll
remove it from my I/F and see if I get the same error.
Leon
Leon
Reply by Bill Knight●May 26, 20052005-05-26
On Thu, 26 May 2005 15:56:37 +0100, Leon Heller wrote:
>> ----- Original Message -----
>> From: "Bill Knight" <BillK@Bill...>
>> To: <lpc2000@lpc2...>
>> Sent: Thursday, May 26, 2005 2:54 PM
>> Subject: Re: [lpc2000] Amontec Chameleon
>>
>>
>>> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
>>>
>>>>----- Original Message -----
>>>>From: "Bill Knight" <BillK@Bill...>
>>>>To: <lpc2000@lpc2...>
>>>>Sent: Thursday, May 26, 2005 2:03 PM
>>>>Subject: Re: [lpc2000] Amontec Chameleon
>>>
>>>
>>>>> I've used it in both WIGGLER and Raven modes with the
LPC. I use an
>>>>> older version of OCBLibRemote with the following command
lines:
>>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
>>>>> or
>>>>> OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
>>>>> The 's' param may be a bit slow but is the
setting for the project on
>>>>> which I am currently working. I typically use the RAVEN
mode except
>>>>> when using CrossWorks which only supports the WIGGLER mode
(they may
>>>>> have
>>>>> RAVEN mode now, not sure). Also, the code for the Chameleon
itsself
>>>>> has
>>>>> not
>>>>> been updated from their web site in some time.
>>>
>>>>I'm using OCD Commander. I've downloaded OCDRemote for
Windows and
>>>>installed
>>>>it, but can't run it and can't find the executable.
>>>
>>> IIRC it is in Cygwin\usr\local\bin
>>> I usually create a Windows link to it in my project directory
setting the
>>> parameters correctly, then just double-click it when it is
needed.
>>
>> Sorry, I found it where you said.
>>
>> I'll see how I get on with it.
>Same error (43) as with OCD Commander. I think
I'll admit defeat and give up
>trying to get it to work.
This SOUNDS like the error that newer versions of OcdLibRemote return
when they find a non-standard WIGGLER. I believe Macraigor's products
have a jumper between a couple of the parallel port pins that the
newer versions of code are checking. I do not know if Amontec has
added that functionality to the FPGA firmware. Others on the mailing
list might be able to confirm either or both. If that is the problem,
you could either acquire an older version of OcdLibRemote or build a
db-25 adapter to add the jumper.