> On Mon, 12 Nov 2007 10:54:13 +0100, S wrote:
>
>> Hi,
>>
>> We need a good embedded CPU board for our next project.
>>
>> It must be equipped with a relative fast processor, lots of RAM,
>> Ethernet (TCP/IP), optionally WiFi, Flash-card interface, at least 3
>> RS232/RS485 ports, some digital I/O, low power and last be not least low
>> cost.
>>
>> The CPU board will be installed on our custom motherboard, where some of
>> our custom hardware will be located.
>>
>> It must be able to run linux or Windows CE
>>
>> We have found the CM-X270 from http://compulab.co.il to be a good
>> candidate - but is that the best? Are there others you would recommend?
>>
>> /S
>
> Just out of curiosity, if you're using a motherboard anyway, why not grab
> some chip manufacturer's reference design and toss it onto your
> motherboard? There should be eval boards out there with nearly everything
> that you want, and you'd save the cost of buying separate boards.
>
Because we are not able to buy the components and manufacture a board at
the same cost as a ready made board. And we save the time and money for
developement and test of a high speed CPU board. We are not going to
sell millions of this board.
We also plan to make different motherboards, depending on our needs. The
CPU board will stay the same.
/S
Reply by Tim Wescott●November 12, 20072007-11-12
On Mon, 12 Nov 2007 10:54:13 +0100, S wrote:
> Hi,
>
> We need a good embedded CPU board for our next project.
>
> It must be equipped with a relative fast processor, lots of RAM,
> Ethernet (TCP/IP), optionally WiFi, Flash-card interface, at least 3
> RS232/RS485 ports, some digital I/O, low power and last be not least low
> cost.
>
> The CPU board will be installed on our custom motherboard, where some of
> our custom hardware will be located.
>
> It must be able to run linux or Windows CE
>
> We have found the CM-X270 from http://compulab.co.il to be a good
> candidate - but is that the best? Are there others you would recommend?
>
> /S
Just out of curiosity, if you're using a motherboard anyway, why not grab
some chip manufacturer's reference design and toss it onto your
motherboard? There should be eval boards out there with nearly everything
that you want, and you'd save the cost of buying separate boards.
--
Tim Wescott
Control systems and communications consulting
http://www.wescottdesign.com
Need to learn how to apply control theory in your embedded system?
"Applied Control Theory for Embedded Systems" by Tim Wescott
Elsevier/Newnes, http://www.wescottdesign.com/actfes/actfes.html
Reply by S●November 12, 20072007-11-12
Andrew Jackson wrote:
>> We need a good embedded CPU board for our next project.
>>
>> It must be equipped with a relative fast processor, lots of RAM,
>> Ethernet (TCP/IP), optionally WiFi, Flash-card interface, at least 3
>> RS232/RS485 ports, some digital I/O, low power and last be not least
>> low cost.
>>
>> The CPU board will be installed on our custom motherboard, where some
>> of our custom hardware will be located.
>>
>> It must be able to run linux or Windows CE
>>
>> We have found the CM-X270 from http://compulab.co.il to be a good
>> candidate - but is that the best? Are there others you would recommend?
>
> I have used the Viper board from Arcom (now Eurotech in Europe). This
> meets your technical requirements, I'm not sure where you are or what
> the cost would be (I bought the development kit which will always be
> more). I have found that their technical support is very good.
>
> Andrew
The Viper board is definitely looking good too. The cost of the dev. kit
is almost insignificant, as long as the boards are cheap.
/S
Reply by Andrew Jackson●November 12, 20072007-11-12
> We need a good embedded CPU board for our next project.
>
> It must be equipped with a relative fast processor, lots of RAM,
> Ethernet (TCP/IP), optionally WiFi, Flash-card interface, at least 3
> RS232/RS485 ports, some digital I/O, low power and last be not least low
> cost.
>
> The CPU board will be installed on our custom motherboard, where some of
> our custom hardware will be located.
>
> It must be able to run linux or Windows CE
>
> We have found the CM-X270 from http://compulab.co.il to be a good
> candidate - but is that the best? Are there others you would recommend?
I have used the Viper board from Arcom (now Eurotech in Europe). This
meets your technical requirements, I'm not sure where you are or what
the cost would be (I bought the development kit which will always be
more). I have found that their technical support is very good.
Andrew
Reply by S●November 12, 20072007-11-12
Hi,
We need a good embedded CPU board for our next project.
It must be equipped with a relative fast processor, lots of RAM,
Ethernet (TCP/IP), optionally WiFi, Flash-card interface, at least 3
RS232/RS485 ports, some digital I/O, low power and last be not least low
cost.
The CPU board will be installed on our custom motherboard, where some of
our custom hardware will be located.
It must be able to run linux or Windows CE
We have found the CM-X270 from http://compulab.co.il to be a good
candidate - but is that the best? Are there others you would recommend?
/S